Dotaz: kompilace jadra v debianovi

[chinook]

mam debiana a jadro 2.4.17 chtel bych je kompilovat na nejake 2.6 protoze chci nainstalovat lmsensor a to pry jede az od jadra 2.6. kompiloval jsem podle teto adresy http://www.debian.org/doc/manuals/reference/ch-kernel.en.html bodu 7.1.1 ale po napsani uname -r mi to hlasi stale stare jadro. Jsem zacatecnik poradi nekdo pls?

Odpovědi

[Ivanhoej]

V Grube alebo Lile si mu povedal ktory kernel ma bootovat?

myslim ze treba update-grub alebo tak nejak Debian uz nepouzivam ak mas grub.

Je nainstalovane jadro? dpkg -l | grep kernel-image #alebo pozri v aptitude

[lesho]

prave dnes som kompilil z toho isteho jadra co bolo pisane hore, siel som podla http://www.e-aiyama.com/~toshi/Computer/Linux/KernelCompile.html pouzivam lilo, a tiez mi to velmi nepomohlo. riesenie bolo v tom, ze lilo mi nechcelo vziat aktualny vmlinuz. doplnil som teda image=/boot/vmlinuz-2.6.13.4

uz to bezi.tu je vypis mojho lilo.conf

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
disk=/dev/hdb
bios=0x80
# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hdb

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hdb6

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b

# Specifies the location of the map file
#
map=/boot/System.map-2.6.13.4

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
#       prompt
#       single-key
#       delay=100
#       timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask,mode)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux2

#image=/vmlinuzn
#       label=Linux1
#       read-only
#       restricted
#       alias=1

image=/boot/vmlinuz-2.6.13.4
        label=Linux2
        read-only
#       restricted
#       alias=2

image=/vmlinuz
        label=LinuxOLD
        read-only
        optional
#       restricted
#       alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#       label=HURD
#       restricted
#       alias=3
other=/dev/hdb1
  label="Windows(hdb1)"