Dotaz: internet cez Lan v SLED 10

[maho]

Prosim poradte mi uz niekto...

Nainstaloval som si SLED 10, na internet som pripojeny cez router, pri instalacii SLED-u siet nabehne a funguje spravne az dovtedy, pokial nerestartujem PC?! Funguje i po dokonceni instalacie. Skusal som vsetko mozne ale....neviem. Nemam staticku IP, pouzivam DHCP. Vsetky distra Linuxu ktore som pouzival fungovali bez toho aby som sa dotkol akehokolvek nastavenia siete. Ubuntu, Aurox, Fedora Core funguju na rovnakom zeleze bez problemov.

PS: rovnaky problem ako popisujem som mal aj so SUSE 10.1, co viedlo k mojej migracii k inemu distru. Pri ifconfig vypise iba lo, eth0 nepozna. Pise ze neexistuje interface... Skusal som uz takmer vsetko co som na forach objavil: metodu ifup, network managera... Preco pri instalacii funguje vsetko OK a po restarte je to mrtve?

Dakujem

Odpovědi

[ZAH]

Typ síťovky ? výpis lspci ? Asi není zaveden modul.

[maho]

sietovka je Marvell 88E8001 Gigabit na doske DFI LanParty UT nF4 Ultra. Vystup lspci nemozem dat, bo som v praci (vo WIN). Co presne znamena ze asi nieje zavedeny modul? Pri prvom spusteni ale zavedeny bol a ja som potom nemenil v konfiguracii nic...

[ZAH]

Měla by být podporována viz http://www.abclinuxu.cz/hardware/show/71815

[DNA]

lsmod by měl dát mezi jinými název modulu pro danou kartu, pokud tam není, je to špatně...

[Michal Kubeček]

Marvell funguje bez problémů, používám ji na ASUS A8V. Především místo ifconfig použijte 'ip link show'. Pokud vám rozhraní eth0 také neukáže, zkuste v souboru /etc/sysconfig/kernel přidat do proměnné MODULES_LOADED_ON_BOOT jméno potřebného modulu (sk98lin). Ukáže-li vám rozhraní, je problém asi jen v tom, že není nakonfigurované, pak zkuste znovu provést konfiguraci (např. příslušným modulem YaSTu).

[maho]

Prikladam relevantne logy:

lspci

00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Contro ller (rev a2)
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTra nsport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Con troller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscella neous Control
01:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ether net Controller (rev 13)
05:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600 GT] (re v a2)

lsmod

Module                  Size  Used by
joydev                  9024  0
xt_pkttype              1792  3
ipt_LOG                 5632  8
xt_limit                2432  8
snd_pcm_oss            42752  0
snd_mixer_oss          16256  1 snd_pcm_oss
snd_seq                46960  0
snd_seq_device          7948  1 snd_seq
button                  6672  0
battery                 9476  0
ac                      4996  0
ip6t_REJECT             4992  3
xt_tcpudp               3072  3
ipt_REJECT              5120  3
xt_state                2048  12
iptable_mangle          2688  0
iptable_nat             7684  0
ip_nat                 15660  1 iptable_nat
iptable_filter          2816  1
ip6table_mangle         2304  0
ip_conntrack           47916  3 xt_state,iptable_nat,ip_nat
nfnetlink               6040  2 ip_nat,ip_conntrack
ip_tables              11080  3 iptable_mangle,iptable_nat,iptable_filter
ip6table_filter         2688  1
ip6_tables             12360  2 ip6table_mangle,ip6table_filter
x_tables               11524  10 xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,xt_tcpudp,ipt_REJECT,xt_state,iptable_nat,ip_tables,ip6_tables
ipv6                  216704  13 ip6t_REJECT
apparmor               48412  0
aamatch_pcre           13440  1 apparmor
loop                   14856  0
dm_mod                 52200  0
i2c_nforce2             6272  0
i2c_core               19472  1 i2c_nforce2
sk98lin               132832  0
ide_cd                 35360  0
ohci_hcd               17284  0
cdrom                  32288  1 ide_cd
ehci_hcd               26760  0
usbcore               108804  3 ohci_hcd,ehci_hcd
snd_intel8x0           30108  1
snd_ac97_codec         82848  1 snd_intel8x0
snd_ac97_bus            2176  1 snd_ac97_codec
snd_pcm                79880  3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer              20868  2 snd_seq,snd_pcm
snd                    50692  10 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore               8672  1 snd
snd_page_alloc          9608  2 snd_intel8x0,snd_pcm
reiserfs              209664  2
edd                     8516  0
fan                     4612  0
thermal                13448  0
processor              22468  1 thermal
sg                     30620  0
sata_nv                 8836  3
libata                 65168  1 sata_nv
amd74xx                12828  0 [permanent]
sd_mod                 16144  4
scsi_mod              121992  3 sg,libata,sd_mod
ide_disk               14976  0
ide_core              115900  3 ide_cd,amd74xx,ide_disk

rcnetwork restart

Shutting down network interfaces:
Shutting down service network  .  .  .  .  .  .  .  .  .  .  .  .  .  done
Hint: you may set mandatory devices in /etc/sysconfig/network/config
Setting up network interfaces:
    lo
    lo        IP address: 127.0.0.1/8                                 done
Setting up service network  .  .  .  .  .  .  .  .  .  .  .  .  .  .  done
SuSEfirewall2: Warning: ip6tables does not support state matching.
Extended IPv6 support disabled.
SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEfirewall2 ...
SuSEfirewall2: Warning: no interface active
SuSEfirewall2: batch committing...
SuSEfirewall2: Firewall rules successfully set



Toto je vypis casti startovacieho logu, sk98lin je nas modul...
Pridal som aj natvrdo do premennej MODULES_LOADED_ON_BOOT meno 
modulu sk98lin, a sprava sa to rovnako!?

<3>sk98lin: Could not read VPD data.
<4>sk98lin: probe of 0000:01:0a.0 failed with error -5
<6>ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> 
GSI 18 (level, low) -> IRQ 58
<3>sk98lin: Could not read VPD data.
<4>sk98lin: probe of 0000:01:0a.0 failed with error -5
.
.
.
.
doneSetting up network interfaces:
    lo        
    lo        IP address: 127.0.0.1/8   
doneWaiting for mandatory devices:  eth-id-00:01:29:d3:b6:17 __NSC__
20 19 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 
eth-id-00:01:29:d3:b6:17                                                            No interface found
failedSetting up service network  .  .  .  .  .  .  failed

 ip link show
1: lo: <> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: sit0: <> mtu 1480 qdisc noop
    link/sit 0.0.0.0 brd 0.0.0.0

[maho]

TAK, problem je vyrieseny!!!

Vyriesil som to tak, ze som pridal do premennej MODULES_LOADED_ON_BOOT meno modulu "skge", co je (stara verzia: sk98lin) (volba v jádře Marvell Yukon chipset). Toto som nasiel na strankach abclinux.cz v sekcii urcenej pre zakladovky ASUS s rovnakou NET kartou, skusil som to aplikovat na moju DFI zakladovku a podarilo sa.

Dakujem vsetkym co sa mi snazili pomoct, velmi si vazim sikovnych a ochotnych ludi z komunity LINUX.