Administrace komentářů

# modprobe b2c2-flexcop-pci
# dmesg
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 7
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK3] -> GSI 7 (level, low) -> IRQ 7
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0c:e9:c2
i2c_adapter i2c-0: adapter [B2C2 FlexCop device] registered
i2c_adapter i2c-0: master_xfer[0] W, addr=0x68, len=2
b2c2-flexcop: i2c master_xfer failed
i2c_adapter i2c-0: master_xfer[0] W, addr=0x68, len=1
i2c_adapter i2c-0: master_xfer[1] R, addr=0x68, len=1
b2c2-flexcop: i2c master_xfer failed
i2c_adapter i2c-0: master_xfer[0] W, addr=0x0f, len=1
i2c_adapter i2c-0: master_xfer[1] R, addr=0x0f, len=1
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete


# lspci
02:08.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02)

# lsmod
Module                  Size  Used by
b2c2_flexcop_pci        7832  0
b2c2_flexcop           26892  1 b2c2_flexcop_pci
dvb_core               74920  1 b2c2_flexcop
mt352                   6084  1 b2c2_flexcop
bcm3510                10244  1 b2c2_flexcop
stv0299                10760  1 b2c2_flexcop
nxt2002                 8772  1 b2c2_flexcop
firmware_class          7936  3 b2c2_flexcop,bcm3510,nxt2002
stv0297                 8064  1 b2c2_flexcop
mt312                   7620  1 b2c2_flexcop
i2c_core               19920  7
b2c2_flexcop,mt352,bcm3510,stv0299,nxt2002,stv0297,mt312

# cat brno
T 626000000 8MHz 2/3 NONE QAM64 8k 1/8 NONE
# dvbscan brno
scanning brno
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 626000000 0 2 9 3 1 2 0
>>> tune to: 626000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
WARNING: >>> tuning failed!!!
>>> tune to: 626000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE (tuning failed)
WARNING: >>> tuning failed!!!
ERROR: initial tuning failed
dumping lists (0 services)
Done.

# dmesg
,,,
i2c_adapter i2c-0: master_xfer[0] W, addr=0x0f, len=1
i2c_adapter i2c-0: master_xfer[1] R, addr=0x0f, len=1
i2c_adapter i2c-0: master_xfer[0] W, addr=0x0f, len=2
i2c_adapter i2c-0: master_xfer[0] W, addr=0x0f, len=2
...