Administrace komentářů

smartctl 5.40 2010-10-16 r3189 [x86_64-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 2.5" HDD MK..52GSX series
Device Model:     TOSHIBA MK3252GSX
Serial Number:    58ALT0R4T
Firmware Version: LV010J
User Capacity:    320 072 933 376 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Mon Feb 21 17:41:09 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                 ( 120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 137) minutes.
SCT capabilities:              (0x0039) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1351
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       3605
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       6
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   066   066   000    Old_age   Always       -       13688
 10 Spin_Retry_Count        0x0033   171   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       2624
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       486
193 Load_Cycle_Count        0x0032   073   073   000    Old_age   Always       -       272592
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       39 (Min/Max 10/68)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       6
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       3
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       102
222 Loaded_Hours            0x0032   075   075   000    Old_age   Always       -       10366
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       326
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 27 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 27 occurred at disk power-on lifetime: 9361 hours (390 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 1f e3 2d e0  Error: ICRC, ABRT 1 sectors at LBA = 0x002de31f = 3007263

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 08 18 e3 2d e0 00      01:26:44.009  WRITE DMA EXT
  35 00 08 00 d9 0f e0 00      01:26:44.009  WRITE DMA EXT
  ea 00 00 00 00 00 a0 00      01:26:44.008  FLUSH CACHE EXT
  aa aa aa aa aa aa aa ff      01:26:43.827  [RESERVED]
  aa aa aa aa aa aa aa ff      01:26:43.650  [RESERVED]

Error 26 occurred at disk power-on lifetime: 9339 hours (389 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 57 04 d9 e0  Error: ICRC, ABRT 1 sectors at LBA = 0x00d90457 = 14222423

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 00 58 03 d9 e0 00      17:24:09.655  WRITE DMA EXT
  35 00 08 98 84 31 e0 00      17:24:09.655  WRITE DMA EXT
  aa aa aa aa aa aa aa ff      17:24:09.563  [RESERVED]
  35 00 08 78 17 63 e0 00      17:24:08.405  WRITE DMA EXT
  35 00 08 30 50 4f e0 00      17:24:08.405  WRITE DMA EXT

Error 25 occurred at disk power-on lifetime: 8241 hours (343 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 02 5e a2 af e4  Error: UNC 2 sectors at LBA = 0x04afa25e = 78619230

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 58 a2 af e0 00   1d+09:17:06.007  READ DMA EXT
  25 00 00 e8 84 0e e0 00   1d+09:17:06.005  READ DMA EXT
  25 00 08 50 a2 af e0 00   1d+09:17:06.005  READ DMA EXT
  25 00 00 e8 83 0e e0 00   1d+09:17:06.002  READ DMA EXT
  25 00 00 e8 82 0e e0 00   1d+09:17:05.997  READ DMA EXT

Error 24 occurred at disk power-on lifetime: 8241 hours (343 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 82 5e a2 af e4  Error: UNC 130 sectors at LBA = 0x04afa25e = 78619230

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 e0 a1 af e0 00   1d+09:16:53.060  READ DMA EXT
  35 00 00 f8 72 27 e0 00   1d+09:16:53.059  WRITE DMA EXT
  35 00 58 e0 7f a0 e0 00   1d+09:16:53.059  WRITE DMA EXT
  35 00 10 20 fc 9f e0 00   1d+09:16:53.058  WRITE DMA EXT
  35 00 08 58 34 9f e0 00   1d+09:16:53.058  WRITE DMA EXT

Error 23 occurred at disk power-on lifetime: 8234 hours (343 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 9a 5e a2 af e4  Error: UNC 154 sectors at LBA = 0x04afa25e = 78619230

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 f8 a1 af e0 00   1d+01:42:09.140  READ DMA EXT
  35 00 08 10 e3 2d e0 00   1d+01:42:09.072  WRITE DMA EXT
  35 00 08 18 e3 2d e0 00   1d+01:42:09.071  WRITE DMA EXT
  35 00 18 38 34 2f e0 00   1d+01:42:09.071  WRITE DMA EXT
  35 00 50 98 07 b5 e0 00   1d+01:42:09.054  WRITE DMA EXT

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.