Administrace komentářů

Například: Seagate Expansion Portable 5TB z toho SMART údaje nedostaneš ani náhodou, vyzkoušeno přitom je tam jmicron JMS577 prostě Seagate tam nahrál svůj šizený FW který nedokáže ani poslat teplotu HDD.

Jediné co z toho dostaneš je kapacita 5T a název "ExpansionPortable"

Po vykuchání a připojení na jiný jmicron řadič mi funguje v NASU OK.

root@nas:/srv/dev-disk-by-label-Data/home/petr # smartctl -a /dev/sdb
smartctl 6.6 2017-11-05 r4594 [armv7l-linux-5.4.51-v7l+] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 2.5 5400
Device Model:     ST5000LM000-2AN170
Serial Number:    WCJ3EQXZ
LU WWN Device Id: 5 000c50 0d01e6539
Firmware Version: 0001
User Capacity:    5 000 981 078 016 bytes [5,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5526 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Oct  1 16:09:37 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 811) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x30a5)	SCT Status supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   079   065   006    Pre-fail  Always       -       70891853
  3 Spin_Up_Time            0x0003   099   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       169
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   253   045    Pre-fail  Always       -       560027
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       135 (51 249 0)
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       16
183 SATA_Downshift_Count    0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   067   053   040    Old_age   Always       -       33 (Min/Max 27/36)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       3
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       189
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       409
194 Temperature_Celsius     0x0022   033   047   000    Old_age   Always       -       33 (0 21 0 0 0)
195 Hardware_ECC_Recovered  0x001a   079   065   000    Old_age   Always       -       70891853
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       4 (1 63 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       506937546
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       9597184
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Je možné že nějaký SW od Seagate se k údajům dostane ale proč nemůže ten převodník komunikovat normálně ale musí se komunikace mršit aby nebyla normálně dostupná.