Administrace komentářů

Wiphy phy0
	wiphy index: 0
	max # scan SSIDs: 20
	max scan IEs length: 425 bytes
	max # sched scan SSIDs: 20
	max # match sets: 11
	Retry short limit: 7
	Retry long limit: 4
	Coverage class: 0 (up to 0m)
	Device supports RSN-IBSS.
	Device supports AP-side u-APSD.
	Device supports T-DLS.
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP-128 (00-0f-ac:4)
		* CMAC (00-0f-ac:6)
	Available Antennas: TX 0x1 RX 0x1
	Configured Antennas: TX 0x1 RX 0x1
	Supported interface modes:
		 * IBSS
		 * managed
		 * AP
		 * AP/VLAN
		 * monitor
		 * P2P-client
		 * P2P-GO
		 * P2P-device
	Band 1:
		Capabilities: 0x116e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT Max RX data rate: 150 Mbps
		HT TX/RX MCS rate indexes supported: 0-7
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 2412 MHz [1] (22.0 dBm)
			* 2417 MHz [2] (22.0 dBm)
			* 2422 MHz [3] (22.0 dBm)
			* 2427 MHz [4] (22.0 dBm)
			* 2432 MHz [5] (22.0 dBm)
			* 2437 MHz [6] (22.0 dBm)
			* 2442 MHz [7] (22.0 dBm)
			* 2447 MHz [8] (22.0 dBm)
			* 2452 MHz [9] (22.0 dBm)
			* 2457 MHz [10] (22.0 dBm)
			* 2462 MHz [11] (22.0 dBm)
			* 2467 MHz [12] (22.0 dBm)
			* 2472 MHz [13] (22.0 dBm)
			* 2484 MHz [14] (disabled)
	Band 2:
		Capabilities: 0x116e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT Max RX data rate: 150 Mbps
		HT TX/RX MCS rate indexes supported: 0-7
		VHT Capabilities (0x33807120):
			Max MPDU length: 3895
			Supported Channel Width: neither 160 nor 80+80
			short GI (80 MHz)
			SU Beamformee
			RX antenna pattern consistency
			TX antenna pattern consistency
		VHT RX MCS set:
			1 streams: MCS 0-9
			2 streams: not supported
			3 streams: not supported
			4 streams: not supported
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT RX highest supported: 0 Mbps
		VHT TX MCS set:
			1 streams: MCS 0-9
			2 streams: not supported
			3 streams: not supported
			4 streams: not supported
			5 streams: not supported
			6 streams: not supported
			7 streams: not supported
			8 streams: not supported
		VHT TX highest supported: 0 Mbps
		Bitrates (non-HT):
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 5180 MHz [36] (22.0 dBm) (no IR)
			* 5200 MHz [40] (22.0 dBm) (no IR)
			* 5220 MHz [44] (22.0 dBm) (no IR)
			* 5240 MHz [48] (22.0 dBm) (no IR)
			* 5260 MHz [52] (22.0 dBm) (no IR, radar detection)
			* 5280 MHz [56] (22.0 dBm) (no IR, radar detection)
			* 5300 MHz [60] (22.0 dBm) (no IR, radar detection)
			* 5320 MHz [64] (22.0 dBm) (no IR, radar detection)
			* 5500 MHz [100] (22.0 dBm) (no IR, radar detection)
			* 5520 MHz [104] (22.0 dBm) (no IR, radar detection)
			* 5540 MHz [108] (22.0 dBm) (no IR, radar detection)
			* 5560 MHz [112] (22.0 dBm) (no IR, radar detection)
			* 5580 MHz [116] (22.0 dBm) (no IR, radar detection)
			* 5600 MHz [120] (22.0 dBm) (no IR, radar detection)
			* 5620 MHz [124] (22.0 dBm) (no IR, radar detection)
			* 5640 MHz [128] (22.0 dBm) (no IR, radar detection)
			* 5660 MHz [132] (22.0 dBm) (no IR, radar detection)
			* 5680 MHz [136] (22.0 dBm) (no IR, radar detection)
			* 5700 MHz [140] (22.0 dBm) (no IR, radar detection)
			* 5720 MHz [144] (22.0 dBm) (no IR, radar detection)
			* 5745 MHz [149] (22.0 dBm) (no IR)
			* 5765 MHz [153] (22.0 dBm) (no IR)
			* 5785 MHz [157] (22.0 dBm) (no IR)
			* 5805 MHz [161] (22.0 dBm) (no IR)
			* 5825 MHz [165] (22.0 dBm) (no IR)
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * start_ap
		 * new_station
		 * new_mpath
		 * set_mesh_config
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * remain_on_channel
		 * set_tx_bitrate_mask
		 * frame
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * tdls_mgmt
		 * tdls_oper
		 * start_sched_scan
		 * probe_client
		 * set_noack_map
		 * register_beacons
		 * start_p2p_device
		 * set_mcast_rate
		 * connect
		 * disconnect
		 * channel_switch
		 * set_qos_map
		 * add_tx_ts
		 * set_multicast_to_unicast
	WoWLAN support:
		 * wake up on disconnect
		 * wake up on magic packet
		 * wake up on pattern match, up to 20 patterns of 16-128 bytes,
		   maximum packet offset 0 bytes
		 * can do GTK rekeying
		 * wake up on GTK rekey failure
		 * wake up on EAP identity request
		 * wake up on 4-way handshake
		 * wake up on rfkill release
		 * wake up on network detection, up to 11 match sets
	software interface modes (can always be added):
		 * AP/VLAN
		 * monitor
	valid interface combinations:
		 * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
		   total <= 3, #channels <= 2
	HT Capability overrides:
		 * MCS: ff ff ff ff ff ff ff ff ff ff
		 * maximum A-MSDU length
		 * supported channel width
		 * short GI for 40 MHz
		 * max A-MPDU length exponent
		 * min MPDU start spacing
	Device supports TX status socket option.
	Device supports HT-IBSS.
	Device supports SAE with AUTHENTICATE command
	Device supports low priority scan.
	Device supports scan flush.
	Device supports per-vif TX power setting
	P2P GO supports CT window setting
	P2P GO supports opportunistic powersave setting
	Driver supports full state transitions for AP/GO clients
	Driver supports a userspace MPM
	Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
	Device supports static SMPS
	Device supports dynamic SMPS
	Device supports WMM-AC admission (TSPECs)
	Device supports configuring vdev MAC-addr on create.
	Device supports TDLS channel switching
	Device supports randomizing MAC-addr in scans.
	Device supports randomizing MAC-addr in sched scans.
	Device supports randomizing MAC-addr in net-detect scans.
	max # scan plans: 2
	max scan plan interval: 65535
	max scan plan iterations: 254
	Supported TX frame types:
		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
	Supported RX frame types:
		 * IBSS: 0x40 0xb0 0xc0 0xd0
		 * managed: 0x40 0xb0 0xd0
		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * mesh point: 0xb0 0xc0 0xd0
		 * P2P-client: 0x40 0xd0
		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * P2P-device: 0x40 0xd0
	Supported extended features:
		* [ VHT_IBSS ]: VHT-IBSS
		* [ RRM ]: RRM
		* [ SCAN_START_TIME ]: scan start timestamp
		* [ BSS_PARENT_TSF ]: BSS last beacon/probe TSF
		* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
		* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
		* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
		* [ EXT_KEY_ID ]: Extended Key ID support
		* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
		* [ DEL_IBSS_STA ]: deletion of IBSS station support
		* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
		* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

Station 60:a4:b7:49:8b:f5 (on wlp2s0)
	inactive time:	2892 ms
	rx bytes:	3352345
	rx packets:	3930
	tx bytes:	604760
	tx packets:	2662
	tx retries:	12
	tx failed:	0
	beacon loss:	0
	beacon rx:	2208
	rx drop misc:	33
	signal:  	-44 [-44] dBm
	signal avg:	-44 [-44] dBm
	beacon signal avg:	-44 dBm
	tx bitrate:	433.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 1
	tx duration:	0 us
	rx bitrate:	433.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 1
	rx duration:	0 us
	authorized:	yes
	authenticated:	yes
	associated:	yes
	preamble:	long
	WMM/WME:	yes
	MFP:		no
	TDLS peer:	no
	DTIM period:	1
	beacon interval:100
	short slot time:yes
	connected time:	220 seconds
	associated at [boottime]:	8.517s
	associated at:	1662917809686 ms
	current time:	1662918029551 ms

Connected to 60:a4:b7:49:8b:f5 (on wlp2s0)
	SSID: wifi-network
	freq: 5180
	RX: 3457370 bytes (4303 packets)
	TX: 634744 bytes (2831 packets)
	signal: -44 dBm
	rx bitrate: 390.0 MBit/s VHT-MCS 8 80MHz short GI VHT-NSS 1
	tx bitrate: 433.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 1

	bss flags:	short-slot-time
	dtim period:	1
	beacon int:	100