Dotaz: Problém ACPI -battery -AC s gentoo

[Robo]

Zdravim Vas. Prosim vas poradte mi. Po prechode na gentoo mi neide spravne ACPI. A to konkretne 2 casti z neho BATTERY a AC. Mam ich zakompilovane priamo v kernely, ale nie ako moduly, resp skusal som ich aj tak ze som tieto muduly natahoval pri starte. V /proc mi neukazuje ani bateriu ani napajanie. Pod Suse linuxom mi to slapalo v pohode. Presiel som na Gentoo koli rychlosti, ta sa neda so suse porovnat. Dakujem za vsetky solidne odpovede, ktore by mi mohli pomoct.

Odpovědi

[oxymoron]

treba priznat farbu :) ... aspon vystup lspci by to chcelo (pod gentoo treba emerge pciutils)

[Robo]

localhost robi # lspci

00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)

00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)

00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)

00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)

00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)

00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)

00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)

00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)

00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)

00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)

00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)

00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)

00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04)

00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)

06:01.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller

06:01.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller

06:01.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller

06:03.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)

06:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

localhost robi # uname -a

Linux localhost 2.6.16-rc2 #1 SMP PREEMPT Wed Feb 8 12:17:31 Local time zone must be set--s i686 Intel(R) Pentium(R) M processor 1.60GHz GenuineIntel GNU/Linux

localhost robi # dmesg | grep ACPI

BIOS-e820: 000000002f6e0000 - 000000002f6ea000 (ACPI data)

BIOS-e820: 000000002f6ea000 - 000000002f700000 (ACPI NVS)

ACPI: RSDP (v000 PTLTD ) @ 0x000f6e60

ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x2f6e371e

ACPI: FADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x2f6e9e88

ACPI: MADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x2f6e9efc

ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x2f6e9fd8

ACPI: MCFG (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x2f6e9f9c

ACPI: SSDT (v001 SataRe SataAhci 0x00001000 INTL 0x20030224) @ 0x2f6e3f0c

ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030224) @ 0x2f6e3ac7

ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x2f6e397b

ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x2f6e3762

ACPI: DSDT (v001 INTEL ALVISO 0x06040000 MSFT 0x0100000e) @ 0x00000000

ACPI: Local APIC address 0xfee00000

ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)

ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)

ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])

ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])

ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])

ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

ACPI: IRQ0 used by override.

ACPI: IRQ2 used by override.

ACPI: IRQ9 used by override.

Using ACPI (MADT) for SMP configuration information

ACPI: bus type pci registered

ACPI: Subsystem revision 20060127

ACPI: Interpreter enabled

ACPI: Using IOAPIC for interrupt routing

ACPI: PCI Root Bridge [PCI0] (0000:00)

PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]

ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)

ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10

ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11

ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)

ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11

ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.

ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)

ACPI: Embedded Controller [EC0] (gpe 29) interrupt mode.

pnp: PnP ACPI init

pnp: PnP ACPI: found 11 devices

PnPBIOS: Disabled by ACPI PNP

PCI: Using ACPI for IRQ routing

ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16

ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 17

ACPI: Power Button (FF) [PWRF]

ACPI: Lid Switch [LID]

ACPI: Power Button (CM) [PWRB]

ACPI: Sleep Button (CM) [SLPB]

ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)

ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])

ACPI: Processor [CPU0] (supports 8 throttling states)

ACPI: Thermal Zone [THRM] (35 C)

ACPI: PCI Interrupt 0000:06:08.0[A] -> GSI 16 (level, low) -> IRQ 17

ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18

ACPI: PCI Interrupt 0000:06:01.2[A] -> GSI 16 (level, low) -> IRQ 17

ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19

ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19

ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20

ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18

ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17

ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17

ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 17 (level, low) -> IRQ 16

[oxymoron]

hmm ziadna zmienka o baterke... skus pohladat v tom vypise nejake errory nie len to co obsahuje ACPI v riadku.... lebo mam podobnu konfiguraciu a povodne som si myslel ze mam zlu dsdt tabulku pokial ti to nieco hovori ..ale som to vyriesil ovela jednoduchsie....ale to nemusi byt tento pripad... aky je to vyrobca?

[Robo]

Vyrobca je Benq. Model S52. Nie je ani jeden ERROR. Ako by som zmenil DSDT tabulku?

[oxymoron]

tak uz jedine co ma napada je asi zisitit nejako parametre jadra s ktorymi sa to SUSE spustalo a vyskusat ich ked to tam slapalo. dsdt zrejme netreba opravovat ked to pod SUSE islo...ale snazil som sa pomoct :)