Dotaz: Debian 4 zatuhava

[Tomiiiiiik]

Zdravim Vas, nize uvadim odkaz na popis serveru na kterem jsem rozjel Debian 4, zhruba mesic Debian fungoval bez problemu, vyuzivam na nem postfix, apache, courier, mysql a webmina. Rad bych se zeptal, jestli se nekdo setkal s tim, ze mi ted po mesici zacal server vytuhavat, jak v grafickem rozhrani tak consoli Musim ho vzdy natvrdo vypnout a znovu zapnout a pak zase cca. 5 minut jede, to zatuhavani je nepravidelne, ale kdyz se prihlasim primo na server pres klavesnici a monitor (na miste), dela to porad to same, zatuhne a nejde pingnout,... muzete mi prosim poradit v cem muze byt problem? Myslite si, ze to muze delat vadna pamet ci kernel? V logu toho moc nevidim Tom

Odpovědi

[Tomiiiiiik]

Zde zasilam vypis dmesg

VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[25f7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:03.0 to 64
pcie_portdrv_probe->Dev[25e3:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcie_portdrv_probe->Dev[25e4:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:04:00.0 to 64
pcie_portdrv_probe->Dev[3500:8086] has invalid IRQ. Check vendor BIOS
Allocate Port Service[0000:04:00.0:pcie10]
Allocate Port Service[0000:04:00.0:pcie11]
PCI: Setting latency timer of device 0000:05:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:00.0:pcie20]
Allocate Port Service[0000:05:00.0:pcie21]
PCI: Setting latency timer of device 0000:05:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:01.0:pcie20]
Allocate Port Service[0000:05:01.0:pcie21]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:09' and the driver 'serial'
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:06' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:07' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 176k freed
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x6
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x7
ACPI: Thermal Zone [THM0] (8 C)
SCSI subsystem initialized
HP CISS Driver (v 3.6.10)
GSI 18 sharing vector 0x3A and IRQ 18
ACPI: PCI Interrupt 0000:13:08.0[A] -> GSI 19 (level, low) -> IRQ 58
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
USB Universal Host Controller Interface driver v3.0
cciss0: <0x3238> at PCI 0000:13:08.0 IRQ 66 using DAC
      blocks= 573367088 block_size= 512
      heads= 255, sectors= 32, cylinders= 70266

      blocks= 573367088 block_size= 512
      heads= 255, sectors= 32, cylinders= 70266

 cciss/c0d0: p1 p2 < p5 p6 >
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x500 irq 14
scsi0 : ata_piix
ata1.00: ATAPI, max UDMA/100
ata1.00: configured for UDMA/100
  Vendor: HL-DT-ST  Model: DVD-RAM GSA-H60L  Rev: E904
  Type:   CD-ROM                             ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x508 irq 15
scsi1 : ata_piix
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 169, io mem 0xf9df0000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 169, node addr 001e0b8e3d92
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 169, io base 0x00001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 177, io base 0x00001020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
GSI 19 sharing vector 0x4A and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 74, io base 0x00001040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 58, io base 0x00001060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
GSI 20 sharing vector 0x52 and IRQ 20
ACPI: PCI Interrupt 0000:01:04.4[B] -> GSI 22 (level, low) -> IRQ 82
uhci_hcd 0000:01:04.4: UHCI Host Controller
uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 6
uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
uhci_hcd 0000:01:04.4: irq 82, io base 0x00003800
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
Attempting manual resume
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
usb 6-1: new full speed USB device using uhci_hcd and address 2
usb 6-1: configuration #1 chosen from 1 choice
kjournald starting.  Commit interval 5 seconds
EXT3-fs: cciss/c0d0p1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 3522570
ext3_orphan_cleanup: deleting unreferenced inode 3522569
ext3_orphan_cleanup: deleting unreferenced inode 3522568
ext3_orphan_cleanup: deleting unreferenced inode 3522567
ext3_orphan_cleanup: deleting unreferenced inode 3522566
EXT3-fs: cciss/c0d0p1: 5 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
usb 6-2: new full speed USB device using uhci_hcd and address 3
usb 6-2: configuration #1 chosen from 1 choice
hub 6-2:1.0: USB hub found
hub 6-2:1.0: 7 ports detected
usbcore: registered new driver hiddev
input: HP Virtual Keyboard as /class/input/input0
input: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
input: HP Virtual Keyboard as /class/input/input1
input: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
input: PC Speaker as /class/input/input2
Floppy drive(s): fd0 is 1.44M
sr 0:0:0:0: Attached scsi generic sg0 type 5
floppy0: no floppy controllers found
Adding 14651240k swap on /dev/cciss/c0d0p5.  Priority:-1 extents:1 across:14651240k
EXT3 FS on cciss/c0d0p1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on cciss/c0d0p6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bnx2: eth0: using MSI
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
bnx2: eth0 NIC Link is Up, 100 Mbps full duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
ACPI: Power Button (FF) [PWRF]
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
mtrr: type mismatch for f0000000,2000000 old: uncachable new: write-combining

[Mr.Yoda]

Pryč s grafickym rozhranim.

[Tomiiiiiik]

No taky bych se ho chtel zbavit, ale momentalne nevim jak, chtel bych ho pak normalne spoustet, pouzivam KDE. Klidne ho zrusim, pokud to pomuze, ale proc to mesic fungovalo a ted se to zasekne a nejde to ani pres textovou konzoli a musim server vypnout natvrdo?

[karl82]

posledni radek

mtrr: type mismatch for f0000000,2000000 old: uncachable new: write-combining

je problem. co tam je za karty?

[Tomiiiiiik]

Jedna se o tento server:

HP ProLiant ML350G5 5405 4GB, 3x146GB SAS, DVD/RW (nastaveno v BIOSu na RAID 5)
Processor(s): (1) Quad-Core Intel Xeon Processor E5405 (2.00 GHz, 80 Watts, 1333 FSB, 12MB (2x6MB) Level 2 cache).
Chipset: Intel 5000Z Chipset.
Memory: 2 GB PC2-5300 (2 x 1 GB) Fully Buffered DIMMs (DDR2-667), Online spare, Advanced ECC.
Network Controller: Embedded NC373i Multifunction Gigabit Server Adapter.
Storage Controller: Smart Array E200i/128 BWWC Controller (RAID 0/1/1+0/5).
Hard Drive: 2 x 146GB 3G SAS 15K 3.5" DP HDD, max 6 x LFF HDD.
Optical Drive: Half-Height SATA DVD RW Optical Drive.
PCI-Express Slots: Six expansion slots (three PCI Express, three PCI-X).
Power Supplies: 800-Watt CE-mark compliant Hot-Plug power supply, Optional second power supply provides redundant operation.
Fans: 2 fans ship standard, 4 fans total supported (does not include power supply or processor heatsink fans).
Form Factor: Tower.

[jjfgjgh]

Rekl bych, ze je to skoro urcite HW chyba. Presne tento server mame tez. Bezi priblizne rok, zrovna shodou okolnosti taky pod Debianem 4.0, a nikdy zadny problem podobneho typu, jak pises ty. Podle toho, ze chvilku jel, tak bych tipoval na prehrivani, takze mrkni jestli BIOS ukazuje teplotu a pokud je nejaka vyssi, hned volej.

[Dalibor Smolík]

Také mám nejasný pocit, že jde o harwarovou chybu. Zkusil bych spustit stresslinux, prověřit paměť a základní desku a reklamovat ..

[Tomiiiiiik]

Mam prave zaruku primo na miste od HP, ale nerad bych je tam tahal, kdyby to nebylo tim. Proto radeji diskutuji nez se spatne rozhodnu ...

[Dalibor Smolík]

To je správné rozhodnutí. Nicméně výpisy poskytnutné stresslinuxem ukážou nebo neukážou chybová hlášení. S tím je pak možné argumentovat u výrobce. Já jsem takto objevil závadu na základní desce. Systém mi pravidelně vytuhoval v nevhodnou chvíli, obrazovka zamrzala. Ve Windows se problém neprojevoval, vypadalo to, že chyba je v Linuxu. Nicméně stresslinux ukázal celou řadu errorů. Za pár týdnů deska odešla úplně (po 2 letech činnosti počítače - nešlo o server, ale domácí stroj). Po výměně desky se již chyba neopakovala.

[Tomiiiiiik]

Jasne, vyzkousim, jen bych potreboval nejaky manualek, chystam se k serveru do Brna, ISO stresslinuxu jsem si vypalil a mrkl jsem na nej nachvilku, jen bych potreboval znat jake prikazy tam mam zkusit at zjistim co nejvice informaci. Chci urcite po techto testech vytahnout pameti po castech, j mozne ze odesla nektera pamet, ale urcite pres stress bych chtel otestovat cely server, ale jak jsem se dival je potreba za prikazy davat nejake dalsi argumenty, ale vubec se v tom nevyznam.

[Dalibor Smolík]

Také na to nejsem expert , jen jsem zvolil testování základní desky, nechal běžet celou noc a na monitoru vybíhaly errory. Funguje to nějak tak, že testování probíhá několikrát dokola, protože napoprvé se chyba nemusí projevit, ale podruhé při testování stejného místa již chyba vyběhne.
Po testování nové desky stejným způsobem ty errory již nevyběhly.

[Tomiiiiiik]

Jeste pridavam vypis

 www4:~# lspci -v
00:00.0 Host bridge: Intel Corporation 5000Z Chipset Memory Controller Hub (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: bus master, fast devsel, latency 0i
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
        Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Capabilities: [100] Advanced Error Reporting

00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=04, subordinate=0e, sec-latency=0
        Memory behind bridge: fde00000-fdefffff
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
        Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Capabilities: [100] Advanced Error Reporting

00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=17, subordinate=19, sec-latency=0
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
        Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Capabilities: [100] Advanced Error Reporting

00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 4 (rev b1) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=0f, subordinate=11, sec-latency=0
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
        Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Capabilities: [100] Advanced Error Reporting

00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 (rev b1) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=12, subordinate=16, sec-latency=0
        I/O behind bridge: 00004000-00004fff
        Memory behind bridge: fdf00000-fdffffff
        Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
        Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Capabilities: [100] Advanced Error Reporting

00:10.0 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:10.1 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:10.2 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
        Subsystem: Hewlett-Packard Company Unknown device 31fd
        Flags: fast devsel

00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 09) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
        Memory behind bridge: fa000000-fbffffff
        Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff
        Capabilities: [40] Express Root Port (Slot-) IRQ 0
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
        Capabilities: [90] Subsystem: Gammagraphx, Inc. Unknown device 0000
        Capabilities: [a0] Power Management version 2
        Capabilities: [100] Virtual Channel
        Capabilities: [180] Unknown (5)

00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company Unknown device 31fe
        Flags: bus master, medium devsel, latency 0, IRQ 169
        I/O ports at 1000 [size=32]

00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company Unknown device 31fe
        Flags: bus master, medium devsel, latency 0, IRQ 177
        I/O ports at 1020 [size=32]

00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company Unknown device 31fe
        Flags: bus master, medium devsel, latency 0, IRQ 58
        I/O ports at 1040 [size=32]

00:1d.3 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 (rev 09) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company Unknown device 31fe
        Flags: bus master, medium devsel, latency 0, IRQ 66
        I/O ports at 1060 [size=32]

00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09) (prog-if 20 [EHCI])
        Subsystem: Hewlett-Packard Company Unknown device 31fe
        Flags: bus master, medium devsel, latency 0, IRQ 169
        Memory at f9df0000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) (prog-if 01 [Subtractive decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 00002000-00003fff
        Memory behind bridge: f9e00000-f9ffffff
        Prefetchable memory behind bridge: 00000000f0000000-00000000f7ffffff
        Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device 31fe

00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09)
        Flags: bus master, medium devsel, latency 0

00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA Storage Controller IDE (rev 09) (prog-if 80 [Master])
        Subsystem: Compaq Computer Corporation Unknown device 3201
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 177
        I/O ports at ignored
        I/O ports at ignored
        I/O ports at ignored
        I/O ports at ignored
        I/O ports at 0500 [size=16]
        Capabilities: [70] Power Management version 2

01:03.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA])
        Subsystem: Hewlett-Packard Company Unknown device 31fb
        Flags: bus master, stepping, medium devsel, latency 64, IRQ 7
        Memory at f0000000 (32-bit, prefetchable) [size=128M]
        I/O ports at 3000 [size=256]
        Memory at f9ff0000 (32-bit, non-prefetchable) [size=64K]
        [virtual] Expansion ROM at f9e00000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2

01:04.0 System peripheral: Compaq Computer Corporation Integrated Lights Out Controller (rev 03)
        Subsystem: Hewlett-Packard Company Unknown device 3305
        Flags: medium devsel, IRQ 5
        I/O ports at 2800 [size=256]
        Memory at f9fe0000 (32-bit, non-prefetchable) [size=512]
        Capabilities: [f0] Power Management version 3

01:04.2 System peripheral: Compaq Computer Corporation Integrated Lights Out  Processor (rev 03)
        Subsystem: Hewlett-Packard Company Unknown device 3305
        Flags: bus master, medium devsel, latency 64, IRQ 10
        I/O ports at 3400 [size=256]
        Memory at f9fd0000 (32-bit, non-prefetchable) [size=2K]
        Memory at f9fc0000 (32-bit, non-prefetchable) [size=8K]
        Memory at f9f00000 (32-bit, non-prefetchable) [size=512K]
        [virtual] Expansion ROM at f9e20000 [disabled] [size=64K]
        Capabilities: [f0] Power Management version 3

01:04.4 USB Controller: Hewlett-Packard Company Unknown device 3300 (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company Unknown device 3305
        Flags: bus master, medium devsel, latency 64, IRQ 74
        I/O ports at 3800 [size=32]
        Capabilities: [f0] Power Management version 3

01:04.6 Serial bus controller [0c07]: Hewlett-Packard Company Unknown device 3302 (prog-if 01)
        Subsystem: Hewlett-Packard Company Unknown device 3305
        Flags: medium devsel, IRQ 5
        Memory at f9ef0000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [f0] Power Management version 3

02:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
        Memory behind bridge: fa000000-fbffffff
        Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff
        Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0
        Capabilities: [90] PCI-X bridge device
        Capabilities: [b0] Power Management version 2
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [14c] Power Budgeting
        Capabilities: [160] Device Serial Number 92-3d-8e-fe-ff-0b-1e-00

03:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12)
        Subsystem: Hewlett-Packard Company Unknown device 7038
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 90
        Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
        [virtual] Expansion ROM at f8100000 [disabled] [size=2K]
        Capabilities: [40] PCI-X non-bridge device
        Capabilities: [48] Power Management version 2
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+

04:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=04, secondary=05, subordinate=0b, sec-latency=0
        Capabilities: [44] Express Upstream Port IRQ 0
        Capabilities: [70] Power Management version 2
        Capabilities: [80] Subsystem: Gammagraphx, Inc. Unknown device 0000
        Capabilities: [100] Advanced Error Reporting

04:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=04, secondary=0c, subordinate=0e, sec-latency=64
        Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
        Capabilities: [6c] Power Management version 2
        Capabilities: [80] Subsystem: Gammagraphx, Inc. Unknown device 0000
        Capabilities: [d8] PCI-X bridge device
        Capabilities: [100] Advanced Error Reporting

05:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=05, secondary=06, subordinate=08, sec-latency=0
        Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
        Capabilities: [70] Power Management version 2
        Capabilities: [80] Subsystem: Gammagraphx, Inc. Unknown device 0000
        Capabilities: [100] Advanced Error Reporting

05:01.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 (rev 01) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=05, secondary=09, subordinate=0b, sec-latency=0
        Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
        Capabilities: [70] Power Management version 2
        Capabilities: [80] Subsystem: Gammagraphx, Inc. Unknown device 0000
        Capabilities: [100] Advanced Error Reporting

12:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev b4) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=12, secondary=13, subordinate=16, sec-latency=64
        I/O behind bridge: 00004000-00004fff
        Memory behind bridge: fdf00000-fdffffff
        Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
        Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0
        Capabilities: [90] PCI-X bridge device
        Capabilities: [b0] Power Management version 2
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [14c] Power Budgeting

13:04.0 PCI bridge: Broadcom HT1000 PCI/PCI-X bridge (rev b2) (prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, medium devsel, latency 64
        Bus: primary=13, secondary=14, subordinate=16, sec-latency=64
        Capabilities: [90] PCI-X bridge device

13:08.0 RAID bus controller: Hewlett-Packard Company Unknown device 3238
        Subsystem: Hewlett-Packard Company Unknown device 3211
        Flags: bus master, fast devsel, latency 64, IRQ 82
        Memory at fdf80000 (64-bit, non-prefetchable) [size=512K]
        I/O ports at 4000 [size=256]
        Memory at fdf70000 (32-bit, non-prefetchable) [size=32K]
        [virtual] Expansion ROM at f8000000 [disabled] [size=16K]
        Capabilities: [c0] Power Management version 2
        Capabilities: [cc] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
        Capabilities: [dc] PCI-X non-bridge device

[Tomiiiiiik]

Tak problem vyresen. Problem je asi v prehrati nejakych komponent v serveru. Nejvice topi chladic na chipsetu, kdyz je server otevreny zatuhne tak za hodinu, pokud je zavreny tak behem 3 minut je mrtvy. Poustel jsem na serveru stresslinux memtest a skoro vzdy ve stejnou chvili se pri testovani RAM zasekl, volal jsem na HP a dnes maji predelat zakladni desku za novou. Tak uvidime, zda-li se problem vyresi ci nikoli. Diky za rady, ktere mi hodne pomohly