Dotaz: Xorg nenajde klavesnici

[ZS-Man]

Ahoj, mam Slackware10, jadro 2.6.7, pomoci swaretu jsem nainstaloval xorg 6.8.1, ale uz mi necteji startovat X-ka

(EE) No input driver matching "Keyboard"
     No core Keyboard
Fatal server error
failed to initialize core devices 

zkusil jsem pouzit puvodni xorg.conf(z verze 6.7.0), nove ho vygenerovat pomoci fglrxconfig, ale je to porad stejne. v xorg.conf mam toto:

Section "InputDevice" 
    Identifier	"Keyboard1"
    Driver	"Keyboard" 
    Option "XkbRules"	"xfree86"
    Option "XkbModel"	"pc101"
    Option "XkbLayout"	"cs"
 
EndSection 

Section "ServerLayout"
    Identifier  "Server Layout"
    Screen "Screen0"
    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"
EndSection 

Takze napada vas neco?

Odpovědi

[Radek Vohnout]

Tento radek Driver "Keyboard" na Driver "keyboard"

Mam stejnou instalaci a u mne to pomohlo

[ZS-Man]

Diky moc, klavesnice je vyresena. Ale dalsi problem na obzoru. Nejde spustit nic, co (asi) pouziva 3D akceleraci. napr. spusteni fglrxinfo, glxgears okamzite schodi X-ka. ovladace mam aktualni z ati.com

[Radek Vohnout]

Jo jo, ale tohle jsem jeste nevyresil, asi si koupim nvidiu... R

[ZS-Man]

No to bych mozna taky udelal, ale jak ji dostat do notebooku? :o)))))) Mozna kladivem, ale abych neprisel o zaruku. No nic, jdu patrat dal......

[David Jež]

Hmmm a notas je co zac? Grafika je co zac? Posli sem vyflus z lspci -vn. Kristalovou kouli sem vcera ucil letat asi, potkala stenu...
-djz

[Radek Vohnout]

Mam stejny problem na desktopu Slackware 10.0, Xorg 6.8.1, ati 3.12 a ATI 9600PRO Nekde jsem cetl neco ve style, ze 6.8.1 je moc nove a ze to beha jenom na 6.7, ale protoze to bylo v holandstine tak jsem tomu uplne presne nerozumnel... R

[David Jež]

viz. odpoved dole. No budto nerozumel nebo to bylo blbe napsane; jde o to ze (zatim) v Xkach nejsou ovladace k novejsim ATI kartam a binarni ovladace od ATI (ktere mimochodem zacala ATI delat az proto, kdyz zjistila co za hajdalackou bandu jsou lidi z XFree, ale to je jina story) funguje pouze s XFree86 a testuje si verzi. A protoze X.org se hlasi jaksi nesmyslne tak si mysli, ze nebezi na XFree86 a nechce fungovat. Proto holt musis budto pouzit starsi Xka, nebo ten pokusny projekt pro X.org nebo pockat rok co vymysli ATI. Ale nejjednodussi a nejpohodlnejsi bude fakt downgradovat Xka na verzi ze Slackware 9.1.
-djz

[mimi.vx]

primo v changelogu slackware current je ze v konfiguraci xorg je chyba a misto "Keyboard" ma uzivatel napsat "kbd" ..
+ binarni ovladace ATI nejsou kompaktibilni s xorg 6.8.0+ ... az nektere pristi vydani ... takze pokud chcete xwin s akceleraci 3d na ati zustat bud u xfree86 4.3.0 nebo u xorg 6.7.0

jinac spousta veci o ati a ovladacich v linuxu najdete na forech www.rage3d.com

[David Jež]

X.org 6.7.0 ani jakykoliv jiny X.org tezko. Ovladace od ATI chcou pouze XFree86 (4.1 4.2 4.3) ktere se navic hlasi jako XFree86 prislusne verze a jeste to kontroluje, coz se X.org samozrejme nehlasi (zadna verze). A X.org sami od sebe 3d na 9500/9700 & spol. neumi ani nahodou, ani omylem. Jedine pres r300.
-djz

[ZS-Man]

?? Xorg 6.7.0 ze neumi 3D ? Ale ano, umi a bez problemu i s ati.com ovladacema. A i s jadernejma ovladacema je 3D funkcni, pouze kvalita a rychlost se mi moc nezamlouvala. Problem mam pouze obcas s Army Ops- viz starsi prispevek. S GeForce 3 to bezi o 106.

[David Jež]

Aha, mas 9200. Tak to nic, ta funguje, myslel jsem s 9500/9700 to je problem.
-djz

[David Jež]

Jo jeste jedna vec. Ovladace z ati.com ze zari (tedy 3.12.0) nejedou ani s X.org 6.8 ani s 6.7...
-djz

[ZS-Man]

Opet nesouhlasim....:o)))) Mam Xorg 6.7.0 a ovladace 3.12.0 a jedou OK. A ovladace 3.11.1 fungovaly taky(pokud si dobre vspominam, tak tam byl na ne potreba patch. A zrovna vcera vysla nova verze, 3.14.1 , tak je jdu skusit s Xorg 6.8.1

[ZS-Man]

Jj, sorry. Takze Notebook ACER Aspire 1356LMI, ATI 9200. Slack 10, jadro 2.6.7 Na Xorg 6.7.0. to behalo temer bez problemu( ve 3D hrach se mi obcas stane, ze se rozszpe obraz na takovy barevny trojuhelniky ktery jako vychazeji ze stredu obrazovky, hra funguje dal, ale treba v ArmyOps musim zmenit rozliseni, pritom mi to spadne do KDE na listu, musim ji poslat na druhou virt. plochu, na ni se prepnout a potom muzu pokracovat ve hre) proto jsem chtel zkusit nova X-ka, jestli se to nezlepsi. No, nezlepsilo......

lspci -v

00:00.0 Host bridge: VIA Technologies, Inc. VT8378 [KM400] Chipset Host Bridge
        Subsystem: VIA Technologies, Inc.: Unknown device 7205
        Flags: bus master, 66Mhz, medium devsel, latency 8
        Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [80] AGP version 3.5
        Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
        Flags: bus master, 66Mhz, medium devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: d0100000-d01fffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        Capabilities: [80] Power Management version 2

00:07.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 0, IRQ 5
        Memory at 20000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        I/O window 0: 00000000-00000003
        I/O window 1: 00000000-00000003
        16-bit legacy interface ports at 0001

00:08.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 5
        Memory at d0004000 (32-bit, non-prefetchable) [size=2K]
        Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2

00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8180 (rev 20)
        Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8180
        Flags: medium devsel, IRQ 9
        I/O ports at 1000 [size=256]
        Memory at d0004800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

00:10.0 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 80) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 4
        I/O ports at 2000 [size=32]
        Capabilities: [80] Power Management version 2

00:10.1 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 80) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 5
        I/O ports at 2020 [size=32]
        Capabilities: [80] Power Management version 2

00:10.2 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 80) (prog-if 00 [UHCI])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 9
        I/O ports at 2040 [size=32]
        Capabilities: [80] Power Management version 2

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 11
        Memory at d0004c00 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, stepping, medium devsel, latency 0
        Capabilities: [c0] Power Management version 2

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 4
        I/O ports at 2060 [size=16]
        Capabilities: [c0] Power Management version 2

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: medium devsel, IRQ 9
        I/O ports at 1400 [size=256]
        Capabilities: [c0] Power Management version 2

00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 80)
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: medium devsel, IRQ 9
        I/O ports at 1800 [size=256]
        Capabilities: [d0] Power Management version 2

00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, medium devsel, latency 64, IRQ 4
        I/O ports at 1c00 [size=256]
        Memory at d0005000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Power Management version 2

01:00.0 VGA compatible controller: ATI Technologies Inc RV250 5c61 [Radeon Mobility 9200 M9+] (rev 01) (prog-if 00 [VGA])
        Subsystem: Acer Incorporated [ALI]: Unknown device 0033
        Flags: bus master, fast Back2Back, 66Mhz, medium devsel, latency 255, IRQ 4
        Memory at d8000000 (32-bit, prefetchable) [size=128M]
        I/O ports at 9000 [size=256]
        Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at (unassigned) [disabled] [size=128K]
        Capabilities: [58] AGP version 3.0
        Capabilities: [50] Power Management version 2

Na googlu jsem zjistil, ze s tim jsou nejake problemy, ale reseni zadne

[David Jež]

Mno super, takze moznosti:

• pro 9200 pouzij ChipID 0x5964 nebo ChipID 0x5961 v konfiguraku u casti s grafikou a bude to fungovat primo s tim co mas v Xkach (XFree 4.3 nebo X.org)
• sehnat si Xka ze Slackware 9.1 a prejit na XFree86-4.3 a k nim nalit binarni ovladace od ATI
• nebo r300 a vybuildovat znova X.org balicek a reinstalovat. Samozrejme doporucuji precist si odstavce v readme o odpovednosti autora a o tom co vsechno soft muze znicit .

-djz