Dotaz: hibernacia a suspend

[dodo2]

ibm r50e + mandrake 10.1 + 2.6.10 kernel (kompilovane s podporou acpi a ibm extras)

zdravim.

pri spusteni hibernacie z "laptop menu" mi pekne zhibernuje, ale cas sa mi zastavi a pri opatovnom spusteni systemu musim ho nastavovat. Da sa tomu vyhnut?

ako suspendovat? pri spusteni z "laptop menu" mi urobi vypis

Stopping services ====================||

a potom sa prepne do suspend. No nezobudi sa z neho a musim restartovat tvrdo.

ako na to? dik za kazdu radu

Odpovědi

[Josef Kufner]

echo standby > /sys/power/state
echo mem > /sys/power/state
echo disk > /sys/power/state

co z tohodle nefunguje? Ve všech pripadech by se mel uspat. Doporucuju pred tim provest sync popripade mount / -o remount,ro

taky sem prihod vystup z:

dmesg|grep ACPI -i

[dodo2]

vypis z dmesg | grep "ACPI" -i

ACPI: setting ELCR to 0200 (from 0800)
ACPI: Subsystem revision 20041105
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 28)
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PCI: Using ACPI for IRQ routing
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU] (supports C1 C2 C3)
ACPI: Processor [CPU] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (34 C)
ibm_acpi: IBM ThinkPad ACPI Extras v0.8
ibm_acpi: http://ibm-acpi.sf.net/
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
ACPI wakeup devices:
ACPI: (supports S0 S3 S4 S5)
ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
..<6>ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
..<6>ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
..<6>ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11

tie hodiny sa mi uz nekazia, prisiel som na to, ze pmsuspend2 to robi zda sa bezchybne. Predtym z klaptop to robilo problemi.

takze: Co mam kde pridat alebo ako spustat aby fungoval aj suspend?

[dodo2]

echo standby > /sys/power/state - urobi len to, co som pisal =

Stoping tasks ==========================|| a vypne sa do standby modu. Ale nenabehne znova, len normalny restart.

echo mem > /sys/power/state - len blikne obrazovka a hned to je naspat

echo disk ... to je asi to iste ako hibernacia, a to mi funguje cez pmsuspend2 dobre.

[medulin]

Cas po hibernaci:

Linux ma dva casy systemovy a hardwarovy ( bios ). Je to kvuli presnosti, ale pri hibernaci jsou stim problemy. Resim to prikazem po probuzeni z hibernace jako root:

hwclock --hctosys precte cas z biosu

hwclock --systohc ulozi cas do biosu

Zatim sem neprisel na to jak to automatizovat aby po probuzeni z hibernace se provedl ten prikaz wclock --hctosys . Uz se to tu resilo vicekrat http://www.abclinuxu.cz/forum/show/42437

mandrake 10.1 + 2.6.10 kernel v teto sestave me ten suspend prave zacal fungovat i zpobouzenim, predtim jsem mel stejny problem.

[jogo]

v /etc/acpi zrobit skript (je potrebne zistit ako by vyzeral subor pre LID v /etd/acpi/events, to je ten cudlik ktory sa stlaci ked sa zatvori laptop)

a v nom po prikazoch

hwclock --systohc echo "nejakahibernacia" > /sys/power/state

napisat

hwclock --hctosys (alebo tu druhu moznost, neviem z hlavy)