Actiontec USB 802.11b (HWU01170)

Ovladač:

dodává někdo jiný

Technické parametry

USB 1.1 adapter s chipsetem PRISM2.5, kompatibilni s IEEE802.11b (11Mbps). Adapter nema konektor pro pripojeni externi anteny.
http://www.actiontec.com/products/broadband/80211b_usb/80211usb_specifications.html

Identifikace pod Linuxem

Bus 001 Device 003: ID 1668:0421 Actiontec Electronics, Inc. [hex]
string descriptor 1 invalid (bf bf; len=0)
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 Interface
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x1668 Actiontec Electronics, Inc. [hex]
  idProduct          0x0421
  bcdDevice            1.32
  iManufacturer           0
  iProduct                0
  iSerial                 1
  bNumConfigurations      1
Warning: invalid config descriptor
  junk at config descriptor end: 00 02 19 00 01 01 00 60 01 09 04 00 00 01 09 00 00 00 07 05 81 03 01 00 ff
  Language IDs: (length=4)
     0409 English(US)

ifconfig:
wlan0     Link encap:Ethernet  HWaddr 00:20:E0:88:5A:19
          inet addr:192.168.0.1  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

messages:
ident: nic h/w: id=0x8010 1.0.0
ident: pri f/w: id=0x15 1.1.2
ident: sta f/w: id=0x1f 1.5.6
MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1
CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1
PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4
STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/10
PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1
STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1

Postup zprovoznění pod Linuxem

stahnout driver z
ftp://ftp.linux-wlan.org/pub/linux-wlan-ng/
pak postupovat podle navodu

moduly: prism2_usb, p80211 do /etc/modules.conf pridat: alias wlan0 prism2_usb konfigurovat /etc/wlan.conf a spustit /etc/init.d/wlan start

a muzete provest treba: ifconfig wlan0 192.168.0.1

nebo treba: cat /proc/net/wireless

USB adapter je podporovan az driverem, ktery je novejsi nez  0.1.14!

Poznámka

Actiontec HWU01170. Testovano s MDK 8.2, kernel 2.4.18mdk. MDK 8.2 obsahuje podporu pro wlan site, ale dodavany driver nepozna tento USB adapter, je trebw stahnout novejsi verzi z internetu, viz vyse.

Dokument vytvořil: Petr Slansky, 8.6.2002 11:08 | Zobrazeno: 1078×