Compaq ProLiant ML370

Ovladač:

dodává výrobce

Technické parametry

930MHz
512MB RAM
HD SCSI 3x18GB - RAID5 36GB
další viz http://www.compaq.cz

---

Identifikace pod Linuxem

processor: 0
vendor_id: GenuineIntel
cpu family: 6
model: 8
model name: Pentium III (Coppermine)
stepping: 6
cpu MHz: 930.434
cache size: 256 KB
[...]
flags: fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr xmm
bogomips: 1854.67

cciss0:  
Compaq Smart Array 5300 Controller
       Board ID: 40700e11
       Firmware Version: 1.28
       Memory Address: e0820000
       IRQ: 0xa
       Logical drives: 1 [...]

Host: scsi1 Channel: 00 Id: 06 Lun: 00
  Vendor: COMPAQ   Model: SDT-10000        Rev: 1.09
  Type:   Sequential-Access                ANSI SCSI revision: 02

---

dmesg:

Linux version 2.4.9-13SGI_XFS_1.0.2 (root@gibble) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Thu Nov 15 11:38:50 CST 2001
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
 BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fffc000 (usable)
 BIOS-e820: 000000001fffc000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Scanning bios EBDA for MXT signature
On node 0 totalpages: 131068
zone(0): 4096 pages.
zone(1): 126972 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/cciss/c0d0p8
Initializing CPU#0
Detected 930.435 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1854.66 BogoMIPS
Memory: 509476k/524272k available (2465k kernel code, 12344k reserved, 97k data, 224k init, 0k highmem)
kdb version 1.9 by Scott Lurndal, Keith Owens. Copyright SGI, All Rights Reserved
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=3
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Discovered peer bus 03
PCI: Device 00:00 not found by BIOS
PCI: Device 00:01 not found by BIOS
PCI: Device 00:78 not found by BIOS
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
mxt_scan_bios: enter
Starting kswapd v1.8
VFS: Diskquotas version dquot_6.5.0 initialized
SGI XFS with ACLs, EAs, quota, no debug enabled
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: queued sectors max/low 338280kB/207208kB, 1024 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
ServerWorks OSB4: chipset revision 0
ServerWorks OSB4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x3400-0x3407, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x3408-0x340f, BIOS settings: hdc:pio, hdd:pio
hda: Compaq CRD-8402B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.97.sv
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ide-floppy driver 0.97.sv
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 369k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Compaq CISS Driver (v 2.4.6)
cciss: Device 0xb060 has been found at bus 3 dev 3 func 0
cciss: using DAC cycles
      blocks= 71122560 block_size= 512
      heads= 255, sectors= 32, cylinders= 8716

blk: queue c0403f80, no I/O memory limit
Partition check:
 cciss/c0d0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 >
sym53c8xx: at PCI bus 0, device 1, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1510D detected 
sym53c8xx: at PCI bus 0, device 1, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1510D detected 
sym53c1510D-0: rev 0x2 on pci bus 0 device 1 function 0 irq 11
sym53c1510D-0: ID 7, Fast-40, Parity Checking
sym53c1510D-1: rev 0x2 on pci bus 0 device 1 function 1 irq 15
sym53c1510D-1: ID 7, Fast-40, Parity Checking
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
blk: queue c1c7de18, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c1c7de18, I/O limit 4095Mb (mask 0xffffffff)
  Vendor: COMPAQ    Model: SDT-10000         Rev: 1.09
  Type:   Sequential-Access                  ANSI SCSI revision: 02
blk: queue dfd51a18, I/O limit 4095Mb (mask 0xffffffff)
XFS mounting filesystem cciss0(104,8)
Freeing unused kernel memory: 224k freed
Adding Swap: 65256k swap-space (priority -1)
XFS mounting filesystem cciss0(104,5)
XFS mounting filesystem cciss0(104,7)
XFS mounting filesystem cciss0(104,2)
XFS mounting filesystem cciss0(104,6)
st: Version 20010812, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi1, channel 0, id 6, lun 0
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
ip_conntrack (4095 buckets, 32760 max)
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
NET4: AppleTalk 0.18a for Linux NET4.0
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin  and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:02:A5:28:43:5B, IRQ 5.
  Board assembly 010101-034, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
iSCSI version 2.0.1.8 ( 8-Aug-2001)
iSCSI control device major number 254
iSCSI: detected HBA df723c1c, host #2
scsi2 : iSCSI (2.0.1.8)
spurious 8259A interrupt: IRQ7.
Compaq rom driver (rev 2.4.0)
cpqw:    Compaq Wellness driver (ver 2.4.0)
sym53c1510D-1-<6,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset 15)
sym53c1510D-1-<6,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset 15)
st0: Block limits 1 - 16777215 bytes.

lspci:

00:00.0 Host bridge: ServerWorks CNB20LE Host Bridge (rev 05)
00:00.1 Host bridge: ServerWorks CNB20LE Host Bridge (rev 05)
00:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c1510 (rev 02)
00:01.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c1510 (rev 02)
00:02.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
00:03.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] (rev 7a)
00:04.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller
00:05.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f)
00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller
03:03.0 RAID bus controller: Compaq Computer Corporation: Unknown device b060 (rev 02)

Postup zprovoznění pod Linuxem

- v první řadě se nenechat odradit na CZ lince technické podpory Compaq
- zapojit, spustit, vložit Compaq SmartStart and Support Software CD a zvolit zkušenou instalaci - Linux
- nastavit RAID pole, doporučuji RAID5
- restartovat, vložit disketu pro instalaci ze sítě a začít normálně instalovat Linux (lze použít i Linux inst. CD)
- po instalaci server poběží, ale větrák bude vydávat zvuky jako při startu letadla
- připojit se na http://www.compaq.com/ > support > servers a stáhnout si Compaq Foundation Agents for Servers - Red Hat Linux
- ihned po instalaci se ventilátor uklidní
- nainstalovat UPS podle návodu k instalaci UPS
- nainstalovat SETI@home :)

---

RedHat 7.2 - SGI XFS
- vložte CD SGI XFS for Red Hat Linux 7.2 Installer, restartujte
- postupně vložte CD RedHat Linux 7.2 Enigma disk 1 a 2
- po instalaci si stáhněte z Internetu Health and Wellness Driver & Compaq Integrated Management Log (IML) Viewer for Red Hat Linux 7.2 (2.4.7-10 kernel) - http://www.compaq.com/ > support > servers, instalujte, ihned po instalaci se uklidní ventilátor
- nainstalujte UPS podle návodu k UPS
- nainstalujte SETI@home :)

Poznámka

Instalace RedHat 7.0 bezproblémová.
Server je vhodný jako PDC pro síť Windows NT, postup zprovoznění najdete na http://hufhendr.spok.cz

---

naprosto bez problémů

Dokument vytvořil: hufhendr, 5.2.2001 10:25 | Poslední úprava: Redakce, 27.2.2011 15:09 | Další přispěvatelé: hufhendr | Historie změn | Zobrazeno: 1830×