Dotaz: Hauppauge WinTV-HVR 1100 (analog)

[maker]

Koupil jsem si tuto kartu a marne se ji snazim zprovoznit. Zkousim zatim pouze analog protoze digital tu jeste neni.

# lspci -s 00:07.0 -vv
00:07.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
        Subsystem: Hauppauge computer works Inc. Unknown device 6701
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium TAbort- TAbort- MAbort- SERR- PERR-
        Latency: 32 (21000ns min, 8000ns max)
        Interrupt: pin A routed to IRQ 193
        Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

Pri startu dojde k natazeni modulu saa7134, ktery zaragistruje zarizeni /dev/video0 a /dev/vbi0.

saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0

Pri pokusu naladit programy scantv vyhodi chybu:

device has no tuner, exiting

Někde jsem se dočetl, že je potřeba použit tuner=63. Po natazeni modulu saa7134 s timto parametrem uz scantv prochazi kanaly ale neni nikde schopen nic najit.

Odpovědi

[CIJOML]

postni celou relevantni cast dmesg, melo by tam byt nekde type=XX a bud autodetect nebo insmod option.

[maker]

Tak už jsem na to přišel. Modul saa7134 co je v mém kernelu 2.6.18 (Debian testing) ještě neobsahuje podporu pro tuto kartu.

To se projevovalo touto hláškou v dmesg.

saa7133[0]: subsystem: 0070:6701, board: UNKNOWN/GENERIC [card=0,autodetected]

Nainstaloval jsem novou verzi V4L podle: http://www.linuxtv.org/v4lwiki/index.php/How_to_build_from_mercurial

a vše funguje v pohodě. Jen pro zvuk je ještě potřeba modul saa7134-alsa: http://www.linuxtv.org/v4lwiki/index.php/Saa7134-alsa

saa7133[0]: found at 0000:00:07.0, rev: 209, irq: 193, latency: 32, mmio: 0xfdfff000
saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-HVR1110 DVB-T/Hybrid [card=104,autodetected]
saa7133[0]: board init: gpio is 6400000
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
input: HVR 1110 as /class/input/input2
ir-kbd-i2c: HVR 1110 detected at i2c-1/1-0071/ir0 [saa7133[0]]
saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tuner 1-004b: chip found @ 0x96 (saa7133[0])
tuner 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfdfff000 irq 193 registered as card -1

Užitečný link je taky http://gentoo-wiki.com/HARDWARE_HVR_1100

[CIJOML]

To jsem rad, ze jsem te nakopnul na spravnou cestu ;) Hodne prijemnych pozitku z hrani.