Dotaz: problem s RTL8111/8168B PCI Express Gigabit Ethernetv jadre 2.6.30 a 2.6.32

[sixberk]

Dobry den, mam problem s moduler r8169. Kdyz modul nahodim v dmesg je:

[ 1739.477716] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1739.477755] r8169 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1739.477782] r8169 0000:04:00.0: setting latency timer to 64
[ 1739.477971] r8169 0000:04:00.0: irq 28 for MSI/MSI-X
[ 1739.479755] eth0: RTL8168c/8111c at 0xffffc2000515e000, db:df:df:d7:db:5b, XID 3c4000c0 IRQ 28


kdyz dam ifconfig -a, sitovka se tam objevi, ale kdyz chci nahodit ip adresu ifconfig eth0 192.168.1.1 vyhodi hlasku :

SIOCSIFFLAGS: Cannot assign requested address

ethtool -i eth0 mi vyhodi:

driver: r8169
version: 2.3LK-NAPI
firmware-version:
bus-info: 0000:04:00.0

ethtool eth0 vypise:

Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
Link detected: yes

lspci -v vypise:
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet
controller (rev 02)
Subsystem: Giga-byte Technology Device e000
Flags: bus master, fast devsel, latency 0, IRQ 28
I/O ports at ee00 [size=256]
Memory at fdeff000 (64-bit, prefetchable) [size=4K]
Memory at fdee0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fde00000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 78-56-34-12-78-56-34-12
Kernel driver in use: r8169
Kernel modules: r8169

Po stahnuti driveru z realtek.com.tw a spusteni ./autorun.sh mi to vypsalo:

Check old driver and unload it.
rmmod r8169
Build the module and install
make[2]: *** No rule to make target `modules'. Stop.
make[1]: *** [modules] Error 2
make: *** [modules] Error 2

pricemz v Makefile je:

KVER := $(shell uname -r)
KDIR := /lib/modules/$(KVER)/build
KMISC := /lib/modules/$(KVER)/kernel/drivers/net/
KEXT := $(shell echo $(KVER) | sed -ne 's/^2\.[567]\..*/k/p')o
KFLAG := 2$(shell echo $(KVER) | sed -ne 's/^2\.[4]\..*/4/p')x
EXTRA_CFLAGS += -DCONFIG_R8168_NAPI
#EXTRA_CFLAGS += -DCONFIG_R8168_VLAN
modules:
ifeq ($(KFLAG),24x)
$(MAKE) -f Makefile_linux24x
else
$(MAKE) -C $(KDIR) SUBDIRS=$(PWD)/src modules
strip --strip-debug r8168.$(KEXT)
endif
clean:
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers Modules.symvers Module.markers *.order
install:
install -m 744 -c r8168.$(KEXT) $(KMISC)
ifneq ($(KFLAG),24x)
r8168-objs := r8168_n.o
r8168-objs += r8168_asf.o
r8168-objs += rtl_eeprom.o
obj-m += r8168.o
endif#($(KFLAG),24x)


Poradte prosim, co mam udelat aby sitovka fungovala korektne.
Dekuji

Odpovědi

[michich]

eth0: RTL8168c/8111c at 0xffffc2000515e000, db:df:df:d7:db:5b, XID 3c4000c0 IRQ 28

Ta MAC adresa je divná. Objevuje se při každém startu stejná? I když počítač před tím úplně vypneš a odpojíš na chvíli od napájení?

[sixberk]

Ano mac adresa je stale stejna, s jakymkoliv jadrem, zacal jsem na 2.6.26 az po 2.6.32. Vypnout ho uplne ze site jsem zatim nezkousel vyzkousim co nejdrive.