Dotaz: hylafax a neodeslani faxu

[jardelo]

Ahoj Mam problem s hylafaxem, nemuzu odeslat ani jeden fax. Vzdycky po navazani spojeni s jinym faxem to po urcite dobe spadne a do logu to vypise "no correction mode". Fax mam Class1. Mozna je to tou tridou faxu, ale uz opravdu nevim co s tim a nikde jsem nic nenasel. Typ modemu a konfigurak si vygeneroval sam hylafax. Nemel jste nekdo takovej problem?

config.ttyS1:
ModemResultCodesCmd: ATX3
ModemDialCmd: ATDT0,,%s
CountryCode: 420
AreaCode: 52
>FAXNumber: +420777856965
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: high
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#

ModemType: Class1
Class1PPMWaitCmd: "delay\0727"
Class1TCFWaitCmd: "delay\0727"
Class1EOPWaitCmd: "delay\0729"
Class1SwitchingCmd: "delay\0727"

Odpovědi

[Ladislav Sückr]

Problém s Hylafaxem nemám - všechno funguje. Akorát mi vygeneroval trošku delší config.ttyS0

CountryCode:		00420
AreaCode:		111
FAXNumber:		"222 333"
LongDistancePrefix:	00420
InternationalPrefix:	00420
DialStringRules:	"etc/dialrules"
ServerTracing:		1
SessionTracing:		0xffffffff
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
#GettyArgs:		"-h %l dx_%s"
GettyArgs:		"-r -b -s %s %l"
LocalIdentifier:	"KDE JSEM"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd:	!Rockwell
ModemModelQueryCmd:	!RC288DPi
ModemRevQueryCmd:	ATI3		# product information
#
ModemDialCmd:		ATDT%s		# T for tone dialing

AreaCode, FAXNumber a LocalIdentifier si změň podle sebe. Hylafax verze 4.1.7

[onmail]

Zkuste pouzit konfiguraky, ktere jsou v HylaFaxu jako sablony. Obcas se stava, ze automaticka konfigurace "pozna" modem ne uplne spravne nebo taky obcas modem potrebuje neco "navic" (holt ani s kompatibilitou Class modemu to nebyva tak horke). Doporucuju vyzkouset nejdriv prave sablonu pro Class 1.