Dotaz: ath5k a hostapd

[Pavel Löbl]

Zdravim,

snazim se postavit AP s kartou tl-wn553ag. Jako klient funguje karta bez problemu. Kdyz pustim hostapd vypis vypada v poradku, ale na klientech sit ve scanu neni a vypis iwconfigu na AP vypada taky nekompletne.

uname -a:

Linux lada 3.0-ARCH #1 SMP PREEMPT Tue Aug 30 07:32:23 UTC 2011 i686 AMD Duron(tm) processor AuthenticAMD GNU/Linux

lspci:

00:09.0 Ethernet controller: Atheros Communications Inc. AR5413 802.11abg NIC (rev 01)

dmesg (pred spustenim hostapd ):

[ 5747.040779] ath5k 0000:00:09.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 5747.041011] ath5k 0000:00:09.0: registered as 'phy1'
[ 5747.682460] ath: EEPROM regdomain: 0x0
[ 5747.682473] ath: EEPROM indicates default country code should be used
[ 5747.682477] ath: doing EEPROM country->regdmn map search
[ 5747.682488] ath: country maps to regdmn code: 0x3a
[ 5747.682495] ath: Country alpha2 being used: US
[ 5747.682499] ath: Regpair used: 0x3a
[ 5747.688380] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 5747.694068] ath5k phy1: Atheros AR5413 chip found (MAC: 0xa4, PHY: 0x61)

vypis hostapd:

Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
nl80211: Add own interface ifindex 9
nl80211: New interface mon.wlan0 created: ifindex=10
nl80211: Add own interface ifindex 10
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
Completing interface initialization
Mode: IEEE 802.11g  Channel: 11  Frequency: 2462 MHz
Flushing old station entries
Deauthenticate all stations
wpa_driver_nl80211_set_key: ifindex=9 alg=0 addr=(nil) key_idx=0 set_tx=1 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=9 alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface wlan0 with hwaddr 94:0c:6d:f9:f3:b9 and ssid 'test'
nl80211: Set beacon (beacon_set=0)
wlan0: Setup of interface done.
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
RTM_NEWLINK, IFLA_IFNAME: Interface 'mon.wlan0' added
Unknown event 5
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'mon.wlan0' added
Unknown event 5
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Unknown event 5

Po spusteni hostapd se uz v dmesg nic nevypise. Pridavam jeste konfigurak hostapd.

hostapd.conf:

interface=wlan0
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
dump_file=/tmp/hostapd.dump
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ssid=test
hw_mode=g
channel=11
auth_algs=1
ignore_broadcast_ssid=0

iwconfig (po spusteni hostapd):

wlan0     IEEE 802.11abg  Mode:Master  Frequency:2.462 GHz  Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          
mon.wlan0  IEEE 802.11abg  Mode:Monitor  Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on

Ted presne nevim jak dal. Je potreba jeste neco konfigurovat zvlast, krome hostapd ?

Dekuji vsem.

Odpovědi

[NN]

Mam pocit, ze tato karta AP mod nepodporuje, pouze Ad-Hoc a klient..

NN

[Pavel Löbl]

Podle ruznych prispevku na netu by rezim master chipset ar5413 mel umet.

[Tom]

Nevím jak s ath5k, ale s madwifi mi tato karta jako AP fungovala. Nevím jestli pod hostapd nebo ručně, ale jela