Dotaz: pcmcia-cs, pcmciautils

[transport]

chcem sa opytat, aky je rozdiel pri poziti pcmcia-cs a pcmciautils

pouzival som pcmcia-cs s jadrom 2.6.10 a zavadzal som si demona pcmcia a modul pre staru xircomku xirc2ps-cs

vsetko fungovalo dobre, siet isla

presiel som teraz na jadro 2.6.13.4 a niekde som cital, ze namiest pcmcia-cs je lepsie pouzivat pcmciautils

tak som pcmcia-cs dal prec a nainstaloval pcmciautils

modul xirc2ps-cs ide zaviest bez problemov, no demona pcmcia nikde nemam (mozno to tak ma byt) a tiez nevidim xirc2ps-cs v /proc/interrupts

kde pri pouzivani pcmcia-cs bola a v /etc/pcmcia/config.opts sa nastavovalo pre nu irq rozsah pacmati a tak

mohli by ste mi to troska objasnit, ako to vlastne je, vdaka vodpred za odpovede.

Odpovědi

[Michal Čihař]

Přečti si Linux Kernel 2.6 PCMCIA.

[transport]

diky, precital som si to a z casti to pomohlo

uvediem tu vypisy a nakoniec bude problem

v /etc/pcmcia/config.opts som si nastavil rozsah pamate, irq a potrebne veci

do /etc/rc.conf som si pridal do modulov xirc2ps-cs

#dmesg
usbcore: registered new driver usbfs
usbcore: registered new driver hub
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 23
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
IrDA: Registered device irda0
nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
IrCOMM protocol (Dag Brattli)
PCI: Found IRQ 11 for device 0000:00:02.0
IRQ routing conflict for 0000:00:06.0, have irq 9, want irq 11
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:02.0 [1014:00eb]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000006
PCI: Found IRQ 11 for device 0000:00:02.1
Yenta: CardBus bridge found at 0000:00:02.1 [1014:00eb]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000010
cs: IO port probe 0x300-0x3ff: excluding 0x330-0x337 0x388-0x38f
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0x40000000
cs: IO port probe 0x300-0x3ff: excluding 0x330-0x337 0x388-0x38f
cs: memory probe 0x60000000-0x60ffffff: clean.
eth0: Xircom: port 0x300, irq 7, hwaddr 00:10:A4:EC:6D:D6
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00008400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)

#lsmod
Module                  Size  Used by
ppp_deflate             5248  0
zlib_deflate           23704  1 ppp_deflate
ppp_async               9984  1
ehci_hcd               32904  0
ohci_hcd               20100  0
uhci_hcd               32144  0
intel_agp              21404  1
agpgart                30032  1 intel_agp
yenta_socket           23436  4
rsrc_nonstatic         12416  1 yenta_socket
ircomm_tty             22408  2
ircomm                 11908  1 ircomm_tty
nsc_ircc               15420  0
irda                  128440  3 ircomm_tty,ircomm,nsc_ircc
crc_ccitt               2176  2 ppp_async,irda
snd_cs4236             14148  4
snd_opl3_lib            9728  1 snd_cs4236
snd_hwdep               7712  1 snd_opl3_lib
snd_cs4236_lib         15360  1 snd_cs4236
snd_mpu401_uart         6656  1 snd_cs4236
snd_rawmidi            21152  1 snd_mpu401_uart
snd_seq_device          7436  2 snd_opl3_lib,snd_rawmidi
snd_cs4231_lib         23936  2 snd_cs4236,snd_cs4236_lib
snd_pcm_oss            50976  0
snd_mixer_oss          18176  2 snd_pcm_oss
snd_pcm                84612  4 snd_cs4236_lib,snd_cs4231_lib,snd_pcm_oss
snd_timer              22532  3 snd_opl3_lib,snd_cs4231_lib,snd_pcm
snd                    48996  17 snd_cs4236,snd_opl3_lib,snd_hwdep,snd_cs4236_lib,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_cs4231_lib,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore               7904  2 snd
snd_page_alloc          8840  2 snd_cs4231_lib,snd_pcm
xirc2ps_cs             18320  1
pcmcia                 33064  1 xirc2ps_cs
pcmcia_core            37656  3 yenta_socket,rsrc_nonstatic,pcmcia
ppp_generic            27540  6 ppp_deflate,ppp_async
slhc                    6656  1 ppp_generic
usbcore               114172  4 ehci_hcd,ohci_hcd,uhci_hcd

#cat /proc/interrupts

           CPU0
  0:     239731          XT-PIC  timer
  1:       1540          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  3:      40122          XT-PIC  irda0
  5:      12824          XT-PIC  CS4231
  7:          4          XT-PIC  1.0
  9:         98          XT-PIC  acpi
 11:          2          XT-PIC  yenta, yenta, uhci_hcd:usb1
 12:      36842          XT-PIC  i8042
 14:       5784          XT-PIC  ide0
 15:         34          XT-PIC  ide1
NMI:          0
LOC:          0
ERR:          0
MIS:          0

kde 1.0 na sedmicke je eth0

#pccardctl ident
Socket 0:
  no product info available
Socket 1:
  product info: "Xircom", "CreditCard 10/100", "CE3-10/100", "1.00"
  manfid: 0x0105, 0x010a
  function: 6 (network)

no a teraz k problemu

pri bootovani sa mi nespusta interface eth0

pouzivam pri bootovani network-profiles, kde mam nadefinovane interface

ked spustim profile s eth0 napise mi ze eth0 no such device unknown device, cize vlastne ako keby sietovka este nebezala

no ale ako vidiet hore sietovka bezi (teda ked uz som v xkach)

a ked zadam /etc/rc.d/network restart a vyberiem profil pre eth0 vsetko nabehne v poriadku aj ked dam ifconfig eth0 up tak sa interface eth0 spusti

cize problem je v tom, ze pocas bootovania ako keby sa nespustila este predtym, nez sa vybera ten sietovy profil

pri pouzivani pcmacia-cs to bezalo

este podotykam, ze momentalne nemam /etc/conf.d/ subor pcmcia, ktory som tam mal, ked som pouzival pcmcia-cs, neviem, ci ho tam treba, ale ako som cital, tak asi ani nie

neviem, ci treba nieco pripisat do /etc/modprobe.conf ako trebars alias eth0 alebo nieco, aby sa sietovka spustala hned pri boote

ak mi viete poradit budem vdacny za vsetky podnety.