Dotaz: TB Fiji: pndspini.bin - help kompilace

[7thatom]

Ahoj, měl bych prosbu, jsem linux zelenáč, ale potřebuji rozjet TB Fiji kartu pod MDK 10.0. Problém je v tom, že mi chybí knihovna pndspini.bin a pndsperm.bin, kterou je nutné zkompilovat ze zdrojáku, viz popis v návodu od driveru:

Download to /tmp and unzip the following file from Turtle Beach (be
#  sure to use the entire URL; some have had trouble navigating to the
#  URL):
#  
#       ftp://ftp.voyetra.com/pub/tbs/pinn/pnddk100.zip
#
#  Unpack this shell archive, and run make in the created directory
#  (you need a C compiler and flex to build the utilities).  This
#  should give you the executables conv, pinnaclecfg and setdigital.
#  conv is only used temporarily here to create the firmware files,
#  while pinnaclecfg is used to configure the Pinnacle or Fiji card in
#  non-PnP mode, and setdigital can be used to set the S/PDIF input on
#  the mixer (pinnaclecfg and setdigital should be copied to a
#  convenient place, possibly run during system initialization).
#
#  To generating the firmware files with the `conv' program, we create
#  the binary firmware files by doing the following conversion
#  (assuming the archive unpacked into a directory named PINNDDK):
#  
#    ./conv < PINNDDK/dspcode/pndspini.asm > /etc/sound/pndspini.bin
#    ./conv < PINNDDK/dspcode/pndsperm.asm > /etc/sound/pndsperm.bin

Jak na to? Fakt s linuxem začínám ale nechci to vzdát. Moc díky. 7thatom

Odpovědi

[User682]

zdravim,
moooc hezky hw.
nevim, jaky driver instalujete, ale zkusil bych alsu. ta ma alespon nejaky progress.oss uz nejaky cas poradne nevyviji.
vice. asi si na tom trochu maknete, pred casem jsem zkousel TB Monterey a nejak se nepovedlo.
nainstalujte alsu z nejakeho balicku. pak bud alsaconf ci nahrat moduly primo.
kdyby to neslo, tak dejte vedet.
bye gf

[7thatom]

Diky za tip, ale dnes jsem zkousel nahrat prikazem modprobe driver pro ALSU a zda se, ze to stejne nejde. Jeste jsem nezkousel vkompilovat do jadra nove alsa ovladace, protoze v 2.6 jadre jsou. Pouzivam Mandrakelinux 10. Vypada to, ze to stejne kolabuje na tom, ze nemam bin soubory pro dsp procesor zvukovky (po modprobe zobrazim prikazem dmesg co se stalo a zatuhne to vzdy na DSP inicalizaci). Nezkusil byste prosim nekdo zkompilovat ty asm soubory do bin postupem uvedenym v navodu od driveru? Asi to bude problem jak alsy tak oss nebo ze by pomohla kompilace alsa ovladacu? Prikazy sndconfig nebo alsaconf nepomahaji, jako PnP nenajdou nic a sndconfig je ekvivalentem modprobe (predpokladam) a alsaconf mi nenabidne v sekci legacy driveru turtle beach. Moc diky predem vsem za pomoc.

[User682]

bez zaruky, radeji si to over na netu (google:// linux convert asm to bin) .
nasm je kompilator zdrojaku asembleru. use: nasm asm_file -o vystup.bin
mozna to bude reseni(zkompilovat mi to na masine slo). zkompilovat mi to slo, ale zda to je prave reseni, to nevim. skutecne overit, nez to budes nahravat do karty (umisti do /etc/sound/).
bye gf

[7thatom]

Ahoj, diky, otestuji to. Pokud bys to nekde mel zkompilovane, poprosil bych pripadne o poslani na milan.smakal zavinac iol.cz (usetrilo by mi to praci, ktere se nebranim, ale preferuji cestu nejmensiho odporu :))).

Diky za rady. 7thatom

[7thatom]

Ahoj, kompilace v NASM probehla OK, zvukovka to snad taky zkousla, ale pise po zadani modprobe a pak dmesg prikazu I/O port conflict (uz ne unable to initialise DSP). Jak lze zjistit volne HW prostredky (I/O + IRQ apod.)? Moc diky za rady, zda se, ze je to na dobre ceste.

[User682]

zkus si prikazy:
modinfo modul_name == seznam parametru

ls /proc/inter*

ls /proc/iomem*

ls /proc/ioport*

// nepamatuju si presny nazvy, proto tak hvezdickova konvence

a pak si tu soubory pres less nebo cat nebo more prohledni.
bye gf

[7thatom]

Diky. Vypnul jsem serial porty v biosu, zpusobovaly konflikt na adresach 0x2x .....zobrazil jsem si nastaveni v mc. Driver ale nahlasi po zadani dmesg chybu "bad eip value" viz:

msnd_pinnacle: Turtle Beach MultiSound (Pinnacle/Fiji) Linux Driver Version 0.8.3.1, Copyright (C) 1998 Andrew Veliath msnd_pinnacle: Non-PnP mode: configuring at port 0x260 msnd_pinnacle: 131072 byte audio FIFOs (x2) msnd_pinnacle: Pinnacle/Fiji revision A-B (Fiji) or A-E (Pinnacle), Xilinx version <= 1.15, I/O 0x140-0x147, IRQ 5, memory mapped to 0xD0000-0xD7FFF msnd_pinnacle: DSP reset msnd_pinnacle: DSP firmware uploaded Unable to handle kernel paging request at virtual address d8905000 printing eip: d8905000 *pde = 17db1067 *pte = 00000000 Oops: 0000 [#1] CPU: 0 EIP: 0060:[d8905000>] Not tainted VLI EFLAGS: 00010246 EIP is at 0xd8905000 eax: 00000000 ebx: 00000000 ecx: 00000000 edx: 00000000 esi: d894cbe0 edi: c0327018 ebp: d54aff8c esp: d54aff80 ds: 007b es: 007b ss: 0068 Process modprobe (pid: 1890, threadinfo=d54ae000 task=d560c040) Stack: d88e62a8 d894d4c0 00000000 d54affa8 d88e6c4c d894cbe0 c0327018 d54affbc c013665b c0327030 d54affbc c013666f 0806e148 0805c1c0 08049410 d54ae000 c010afa9 0806e148 000080a3 0805c1c0 0805c1c0 08049410 bffff638 00000080 Call Trace: [d88e62a8>] 0xd88e62a8 [d88e6c4c>] 0xd88e6c4c [c013665b>] sys_init_module+0xcb/0x1b0 [c013666f>] sys_init_module+0xdf/0x1b0 [c010afa9>] sysenter_past_esp+0x52/0x79

Code: Bad EIP value. <6>[drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox G400/G450 (AGP) agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. sndconfig.real: numerical sysctl 1 23 is obsolete. agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.

Co to muze byt? Predem diky za rady (musel jsem z vypisu odstranit < forum me nepustilo dal) 7thatom

p.s. moje HW konfigurace je Duron 1300, Matrox Millenium G400, chipset desky VIA KT133, realtek sitovka a prave TB Fiji

[User682]

dalsi komunikaci bych nechal na jabber ci icq. ono to i rychleji popojede.nejak si udelam cas nektery vecer pres net.
pak udelej zaznam na abicko na tuto kartu, az pojede.
zatim mi posli mailem soubor kernel.log a soubor vznikly lspci -vvv > soubor.txt
mail: goldenfish (zawinac) bsys [bodka]cz
snad se to zprovozni, ale vzhledem, ze pouzivas mandrake, tak to nemuzu zarucit. tohle distro zarovna neni neco, co bych musel. ale nejak se to zkusi.
bye gf

[7thatom]

AHOJ, UZ TO JEDEEEE!!!!!!! Nepouzil jsem nakonec OSS driver, ktery hlasil tuhle chybu, ale Alsa driver. Ten OSS mohl mit problem s jadrem 2.6 (autor - andrew na svych strankach pise pouze verzi 2.4). Jeste musim rozjet MIDI port (asi bude stacit spravne vybrat I/O a IRQ pro MPU401). Az to cele doladim napisu postup pro ostatni. DIKY MOC za pomoc, s linuxem jsem zacal teprve pred tydnem a nejak jsem nevedel kam sahnout :].

[7thatom]

Jeste mam jeden problem, system vidi pouze midi in, ale ne midi out (napr v sequenceru rosegarden nebo ve wired). Konfiguruji to nasledujicimi prikazy (zajimavy je, ze pokud nedam mpu_io a mpu_irq chova se to shodne):

modprobe snd-msnd-pinnacle cfg=0x260 io=0x100 irq=5 mem=0xc8000 modprobe mpu_io=0x200 mpu_irq=7 modprobe snd-pcm-oss modprobe snd-mixer-oss modprobe snd-seq-oss

toto je systemovy vypis pri inicializaci:

snd_msnd_pinnacle: Turtle Beach MultiSound (Pinnacle/Fiji) Linux Driver Version 0.1.3.0, Copyright (C) 2002 Karsten Wiese 1998 Andrew Veliath snd_msnd_pinnacle: Non-PnP mode: configuring at port 0x260 snd_msnd_pinnacle: Configuring MPU to I/O 0x200 IRQ 7 snd_msnd_pinnacle: Pinnacle/Fiji revision A-B (Fiji) or A-E (Pinnacle), Xilinx version <= 1.15, I/O 0x100-0x107, IRQ 5, memory mapped to 0xC8000-0xCFFFF snd_msnd_pinnacle: DSP reset snd_msnd_pinnacle: DSP firmware uploaded

help ke karte: http://www.alsa-project.org/alsa-doc/doc-php/template.php?company=Turtle+Beach&card=Pinnacle.&chip=&module=msnd-pinnacle

predem dekuji za pomoc

[7thatom]

Jeste prikladam vypis lsmod

module Size Used by mga 110976 32 sg 38044 0 st 38616 0 sr_mod 17028 0 sd_mod 16832 0 scsi_mod 114648 4 sg,st,sr_mod,sd_mod md5 3872 1 ipv6 232352 10 parport_pc 32832 0 lp 12200 0 parport 38952 2 parport_pc,lp af_packet 20520 2 ide-floppy 18752 0 ide-tape 34864 0 ide-cd 40548 0 cdrom 37184 2 sr_mod,ide-cd floppy 59444 0 8139too 23712 0 mii 4992 1 8139too supermount 37876 1 snd-seq-midi 8160 1 snd-seq-oss 31232 0 snd-seq-midi-event 7552 2 snd-seq-midi,snd-seq-oss snd-seq 51024 9 snd-seq-midi,snd-seq-oss,snd-seq-midi-event snd-pcm-oss 51812 0 snd-mixer-oss 17952 1 snd-pcm-oss snd-msnd-pinnacle 24576 2 snd-rawmidi 23616 2 snd-seq-midi,snd-msnd-pinnacle snd-seq-device 8008 4 snd-seq-midi,snd-seq-oss,snd-seq,snd-rawmidi snd-pcm 93156 2 snd-pcm-oss,snd-msnd-pinnacle snd-page-alloc 11972 1 snd-pcm snd-timer 24484 2 snd-seq,snd-pcm snd 52484 14 snd-seq-midi,snd-seq-oss,snd-seq-midi-event,sndacle,snd-rawmidi,snd-seq-device,snd-pcm,snd-timer soundcore 9248 2 snd-msnd-pinnacle,snd via-agp 7360 1 agpgart 31016 2 via-agp joydev 10240 0 tsdev 7168 0 evdev 9504 0 usbmouse 5216 0 hid 53312 0 uhci-hcd 29104 0 usbcore 99132 5 usbmouse,hid,uhci-hcd rtc 11576 0 ext3 110408 2 jbd 54328 1 ext3