Dotaz: nvtv, tvout, geforce2, fc3, xorg.conf

[hawran]

chtel bych poprosit o radu ohledne zprovozneni TVoutu na nvidia geforce 2.

pouzivam Fedora Core 3, mam nainstalovany ovladac generic "nv" a taky nvtv utilitu

o co jde:

absolutne si nerozumim s nvtv a to v tom, ze kdyz zapnu volbu TV ON, tak se mi zmeni rozliseni na monitoru a obraz se cely posle do televize, ale ani tam se nezobrazuje korektne. Dokonce i tusim kde je problem, bude to urcite v mym souboru xorg.conf

rovnou to poslu, aby bylo jasno o cem je rec:

Section "Monitor"

Identifier "Monitor0"

VendorName "Monitor Vendor"

ModelName "Proview 996N"

DisplaySize 370 270

HorizSync 30.0 - 98.0

VertRefresh 50.0 - 160.0

ModeLine "1280x1024" 150.0 1280 1344 1504 1728 1024 1025 1028 1072 +hsync +vsync

Option "dpms"

EndSection

Section "Device"

Identifier "Videocard0"

Driver "nv"

VendorName "Videocard vendor"

BoardName "NVIDIA GeForce 2 MX (generic)"

EndSection

Section "Screen"

Identifier "Screen0"

Device "Videocard0"

Monitor "Monitor0"

DefaultDepth 24

SubSection "Display"

Viewport 0 0

Depth 16

Modes "800x600" "640x480"

EndSubSection

SubSection "Display"

Viewport 0 0

Depth 24

Modes "1280x1024" "1280x960" "1152x864" "1024x768"

"800x600" "640x480"

EndSubSection

EndSection

tohle je moje aktualni nastaveni.

monitor proview jede na rozliseni 1280x1024@85hz.

jake parametry bych mel nastavit, aby se mi ten tvout zacal chovat tak jak ma?

chtel bych ten tvout pouzivat predevsim na prehravani filmu na televizi, o nic jineho prakticky nejde. Jen potrebuju aby monitor i tvout jely zaroven (protoze mam tv daleko od pc)...

muzete prosim poradit?

Odpovědi

[Pavel Stárek]

No, kdyby jste si nainstaloval ovladače dodávané přímo NVidií, tak u nich je krásně popsaný příklad xorg.conf s takzvaným twinview a předesílám, že kdysi jsem to zkoušel na MDK9.2 a fungovalo to. Jinak popis instalace NVidia driverů do FC3 je tady .

[hawran]

tak ovladace pro grafiku uz mam nainstalovane a zda se, ze jedou. chtel bych poprosit o pomoc s konfiguraci twinview v xorg.conf. jedna se mi o to, ze bych chtel do tvoutu poustet 800x600 a na klasickym monitoru mit 1280x1024. zkousel jsem to pres NVTV ale jen to ten obraz na tvoutu zmrsilo...

googloval jsem,ale nic relevantniho jsem nenasel... :-/

[Pavel Stárek]

No tu sekci Device bych zkusil upravit takto:

Section "Device"
	Identifier  "Card0"
	Driver      "nvidia"
	VendorName  "NVidia"
	BoardName   "GeForce2 MX"
	Option "IgnoreEDID" "1"
	Option "TwinView"
	Option "SecondMonitorHorizSync"     "30-50"
	Option "SecondMonitorVertRefresh"   "60"
	Option "MetaModes" "1024x768, 1024x768; 800x600, 800x600; 640x480, 640x480;"
	Option "TVStandard" "PAL-G"
EndSection

a uvidí se, jestli to pojede.

[hawran]

udelejme to jinak: aby bylo jasno, tak zde je muj xorg.conf, byl bych rad kdybyste se na to mrknuli a pripadne mi poradili jak postupovat dal. mam to zbastleny dost halabala, protoze se v tom spis topim. klidne muzete ten kofigurak upravit a cely vlozit... necham to na vas.

kazdopadne mockrat diky

# Xorg configuration created by system-config-display

Section "ServerLayout"
        Identifier     "single head configuration"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"

# RgbPath is the location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
        RgbPath      "/usr/X11R6/lib/X11/rgb"
        FontPath     "unix/:7100"
EndSection

Section "Module"
        Load  "dbe"
        Load  "extmod"
        Load  "fbdevhw"
        Load  "glx"
        Load  "record"
        Load  "freetype"
        Load  "type1"
        Load  "dri"
EndSection

Section "InputDevice"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#       Option  "Xleds"         "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
#       Option  "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#       Option  "XkbModel"      "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#       Option  "XkbModel"      "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#       Option  "XkbLayout"     "de"
# or:
#       Option  "XkbLayout"     "de"
#       Option  "XkbVariant"    "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#       Option  "XkbOptions"    "ctrl:swapcaps"
# Or if you just want both to be control, use:
#       Option  "XkbOptions"    "ctrl:nocaps"
#
        Identifier  "Keyboard0"
        Driver      "kbd"
        Option      "XkbModel" "pc105"
        Option      "XkbLayout" "cz_qwerty"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "IMPS/2"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5"
        Option      "Emulate3Buttons" "yes"
EndSection

Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Monitor Vendor"
        ModelName    "Proview 996N"
        DisplaySize  370        270
        HorizSync    30.0 - 98.0
        VertRefresh  50.0 - 160.0
        ModeLine     "1280x1024" 150.0 1280 1344 1504 1728 1024 1025 1028 1072 +hsync +vsync
        Option      "dpms"
EndSection

#tohle by melo nastavit TELEVIZI

Section "Monitor"
        Identifier "monitor1"
        VendorName "Philips"
        HorizSync 30-40
        VertRefresh 50
        DisplaySize 465 350
        ModeLine "720x576/50p" 27 720 744 800 864 576 581 583 625 #27.0 MHz, 31.2 kHz, 50.0 Hz
        Modeline "800x600/50p" 31.60 800 824 968 1000 600 602 603 632 #31.6 MHz, 31.6 kHz, 50.0 Hz
        Option "dpms"

EndSection


#EndSection



Section "Device"
        Identifier  "Videocard0"
        Driver      "nvidia"
        VendorName  "Videocard vendor"
        BoardName   "NVIDIA GeForce 2 MX (generic)"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Videocard0"
        Monitor    "Monitor0"
        DefaultDepth     24
        SubSection "Display"
                Viewport   0 0
                Depth     16
                Modes    "800x600" "640x480"
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
                Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
        EndSubSection
       Option      "TwinView"
        Option      "TwinViewOrientation" "Clone"
        Option      "SecondMonitorHorizSync" "30-50"
        Option      "SecondMonitorVertRefresh" "60"
        Option      "MetaModes" "1280x1024, 800x600"
        Option      "ConnectedMonitor" "CRT, TV"
        Option      "TVStandard" "PAL-B"
        Option      "TVOutFormat" "COMPOSITE"
EndSection

Section "DRI"
        Group        0
        Mode         0666
EndSection

[Pavel Stárek]

Tak, třebas:

# Xorg configuration created by system-config-display

Section "ServerLayout"
        Identifier     "single head configuration"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"

# RgbPath is the location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
        RgbPath      "/usr/X11R6/lib/X11/rgb"
        FontPath     "unix/:7100"
EndSection

Section "Module"
        Load  "dbe"
        Load  "extmod"
        Load  "fbdevhw"
        Load  "glx"
        Load  "record"
        Load  "freetype"
        Load  "type1"
#       Load  "dri"
EndSection

Section "InputDevice"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#       Option  "Xleds"         "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
#       Option  "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#       Option  "XkbModel"      "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#       Option  "XkbModel"      "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#       Option  "XkbLayout"     "de"
# or:
#       Option  "XkbLayout"     "de"
#       Option  "XkbVariant"    "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#       Option  "XkbOptions"    "ctrl:swapcaps"
# Or if you just want both to be control, use:
#       Option  "XkbOptions"    "ctrl:nocaps"
#
        Identifier  "Keyboard0"
        Driver      "kbd"
        Option      "XkbModel" "pc105"
        Option      "XkbLayout" "cz_qwerty"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "IMPS/2"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5"
        Option      "Emulate3Buttons" "yes"
EndSection

Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Monitor Vendor"
        ModelName    "Proview 996N"
        DisplaySize  370        270
        HorizSync    30.0 - 98.0
        VertRefresh  50.0 - 160.0
        ModeLine     "1280x1024" 150.0 1280 1344 1504 1728 1024 1025 1028 1072 +hsync +vsync
        Option      "dpms"
EndSection

#tohle by melo nastavit TELEVIZI
#tohle tam asi byt nemusi
Section "Monitor"
        Identifier "monitor1"
        VendorName "Philips"
        HorizSync 30-40
        VertRefresh 50
        DisplaySize 465 350
        ModeLine "720x576/50p" 27 720 744 800 864 576 581 583 625 #27.0 MHz, 31.2 kHz, 50.0 Hz
        Modeline "800x600/50p" 31.60 800 824 968 1000 600 602 603 632 #31.6 MHz, 31.6 kHz, 50.0 Hz
        Option "dpms"

EndSection


#EndSection



Section "Device"
        Identifier  "Videocard0"
        Driver      "nvidia"
        VendorName  "Videocard vendor"
        BoardName   "NVIDIA GeForce 2 MX (generic)"
	Option      "IgnoreEDID" "1"
	Option      "TwinView"
        Option      "TwinViewOrientation" "Clone"
        Option      "SecondMonitorHorizSync" "30-50"
        Option      "SecondMonitorVertRefresh" "60"
        Option      "ConnectedMonitor" "CRT, TV"
        Option      "TVStandard" "PAL-B"
        Option      "TVOutFormat" "COMPOSITE"
	Option      "MetaModes" "1024x768, 1024x768; 800x600, 800x600; 640x480, 640x480;"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Videocard0"
        Monitor    "Monitor0"
        DefaultDepth     24
        SubSection "Display"
                Viewport   0 0
                Depth     16
                Modes    "800x600" "640x480"
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
                Modes    "1280x1024" "1280x960" "1152x864" "1024x768" "800x600" "640x480"
        EndSubSection
EndSection

Section "DRI"
        Group        0
        Mode         0666
EndSection