Compaq nc6000

Ovladač:

v jádře

Technické parametry

Intel Pentium M 1600MHz (Centrino, 400MHz FSB, ICH4)
Radeon Mobility 9600 M10 (RV350), Atheros WiFi AR5212 (802.11abg), 1Gb NIC Broadcom NetXtreme (BCM5705M_2), 2x O2 Micro SmartCardBus (Yenta), 2x USB 2 (UHCI/EHCI), 14.1" XGA TFT (native 1400x1050@60), SmartLink AMRMO modem (sil27), AC'97 audio (Alsa, Intel 8x0 - 802801DBM), USB Bluetooth, SD/MMC Card Reader (OZ711Mx), FIR (jako Toshiba?), I2C: SMBus I801 + senzor ADM1031
Informace od vyrobce

Identifikace pod Linuxem

CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05
fast FPU, APIC, MTRR, ACPI (8 throttling states - min. 12W@600MHz, 3 thermal zones, battery charge/fan status), RTC, NVRAM, UDMA5 (hda: HTS548060M9AT00, hdc: SD-R2512 /24x CD-RW/DVD-ROM/, povolit v kernelu PIIX), i8042 MUX, Synaptics Touchpad, HCI USB Bluetooth, Intel 855PM AGP (aperture 256MB), Gigabit Ethernet (tg3), SMC SuperIO (LPC47N227, FIR/SIR)

# sensors
eeprom-i2c-0-50
Adapter: SMBus I801 adapter at 1200
Memory type:            DDR SDRAM DIMM
Memory size (MB):       512

adm1031-i2c-0-2c
Adapter: SMBus I801 adapter at 1200
CPU Fan:  1323 RPM  (min = 1323 RPM, div = 2)
Case Fan: 1323 RPM  (min = 1323 RPM, div = 2)
SYS Temp:  +44.2 C  (low  =    +0 C, high =   +60 C)
SYS Crit:    +85 C
CPU Temp:  +43.0 C  (low  =  -128 C, high =   +45 C)
CPU Crit:    +85 C
AUX Temp:  +57.9 C  (low  =  -128 C, high =   +70 C)
AUX Crit:    +85 C

# acpi -V
     Battery 1: charged, 98%
     Thermal 1: ok, 44.0 degrees C
     Thermal 2: ok, 58.0 degrees C
     Thermal 3: ok, 29.0 degrees C
  AC Adapter 1: on-line

Postup zprovoznění pod Linuxem

Kernel 2.6.9 a XFree86 4.3.0.dfsg.1-6ubuntu25.1 na Ubuntu Warty Warthog
MadWiFi CVS
cvs -z3 -d:pserver:anonymous@cvs.sourceforge.net:\
/cvsroot/madwifi co madwifi
=> ath_hal.ko, ath_pci.ko, wlan.ko + /dev/ath0
slmodem 2.9.6 => slamr.ko, slusb.ko + slmodemd + /dev/ttySL0
swsusp 2.1.5 for 2.6.9 + hibernate-script 1.02 => funguje hibernovani (i z X a vcetne korektniho ACPI poweroff)
toshsat1800-irdasetup 0.2 + setserial /dev/ttyS2 uart none + smsc_ircc2 => inicializuje se IrDA v SuperIO, ale nenajde se transciever => zatim nerzchozeno (dalsi info)
synaptics 0.13.2 => v X funguje i tapping a drag'n'drop
Bluez (bluez-utils, bluez-sdp, bluez-pin) + bluetooth, hci_usb, rfcomm => funguje bluetooth a dialup pres GPRS (testovano s Nokia 6310i)
aby spojeni po 4min. nepadalo kvuli LCP reply, musi se upravit nastaveni /etc/ppp/peers/wvdial:

noauth
name wvdial
ipcp-accept-local
novj novjcomp nobsdcomp noipx
lcp-echo-interval 0
passive noproxyarp

SD/MMC card reader - jen info, podpora radice zatim neexistuje. vyrobce LM sensors: eeprom + adm1031 + i2c_i801 + i2c_sensor + i2c_core => funkcni vystup z prikazu sensors

Poznámka

ACPI S3 nefunguje (neprobere se), IrDA nenajde transciever, Yenta udajne potrebuje opravit rozsah portu - netestovano, SD reader nenajde radic
nepouzivat cpufreq (nejede detekce zmeny AC/battery), powernowd bezi v pohode
HW sensory: cerpano hlavne z nc6000 HOWTO od Patricka Reynoldse
ve VMWare je potreba zaskrtnout Legacy support u CDROM, jinak neni videt
MultiBay CD lze za chodu vymenit za floppy (+modprobe floppy), /dev/hdc zustane v /dev, ale pristupu na nej zpusobi oops => funkcni, ale ne blbovzdorne. Certifikace od SuSE (znacne pofiderni, ale prece).

Dokument vytvořil: Jiri Bajer, 4.8.2004 09:54 | Zobrazeno: 1633×