Tiga TI-693A+S

Ovladač:

v jádře

Technické parametry

zalozena na VIA Apollo Pro133 VT82C693A + VT82C686A

rozmer Baby AT (220x186mm), napajeci konektory AT i ATX
AGP 2x; 3x PCI 1x ISA; 1x AMR; integrovana zvukovka AC97
bohuzel jen 2x DIMM , max 512 MB
umi merit teplotu CPU, desky a cipsetu, nektera napajeci napeti a otacky (2 vetraky)

Identifikace pod Linuxem

lspci:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691[Apollo PRO] (rev 44)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 22)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10)
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 [Apollo Super AC97/Audio] (rev 20)

cat /proc/ide/via

----------VIA BusMastering IDE Configuration----------------
Driver Version:                     3.29
South Bridge:                       VIA vt82c686a
Revision:                           ISA 0x22 IDE 0x10
Highest DMA rate:                   UDMA66
BM-DMA base:                        0xd000
PCI clock:                          33MHz
Master Read  Cycle IRDY:            0ws
Master Write Cycle IRDY:            0ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush:          yes                 yes
End Sector FIFO flush:         no                  no
Prefetch Buffer:               no                  no
Post Write Buffer:             no                  no
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   80w                 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:       UDMA       PIO      UDMA      UDMA
Address Setup:       30ns     120ns      30ns      30ns
Cmd Active:          90ns      90ns      90ns      90ns
Cmd Recovery:        30ns      30ns      30ns      30ns
Data Active:         90ns     330ns      90ns      90ns
Data Recovery:       30ns     270ns      30ns      30ns
Cycle Time:          30ns     600ns     120ns      60ns
Transfer Rate:   66.0MB/s   3.3MB/s  16.5MB/s  33.0MB/s

vypis sensors (soucast lm_sensors)

eeprom-i2c-0-50
Adapter: SMBus Via Pro adapter at 5000
Algorithm: Non-I2C SMBus adapter
Memory type:            SDRAM DIMM SPD
SDRAM Size (MB):        xxx

eeprom-i2c-0-51
Adapter: SMBus Via Pro adapter at 5000
Algorithm: Non-I2C SMBus adapter
Memory type:            SDRAM DIMM SPD
SDRAM Size (MB):        xxx

via686a-isa-6000
Adapter: ISA adapter
Algorithm: ISA algorithm
CPU core:  +1.72 V  (min =  +1.62 V, max =  +1.79 V)
3.3V I/O:  +3.20 V  (min =  +2.95 V, max =  +3.62 V)
+5V:       +5.14 V  (min =  +4.47 V, max =  +5.49 V)
+12V:     +11.74 V  (min = +10.79 V, max = +13.18 V)
P/S Fan:     0 RPM  (min = 3000 RPM, div = 2)
CPU Fan:  3040 RPM  (min = 2700 RPM, div = 2)
CPU Temp:  +34.9°C  (limit =  +52°C, hysteresis =  +45°C)
VIA Temp:  +24.4°C  (limit =  +30°C, hysteresis =  +25°C)

Postup zprovoznění pod Linuxem

doporucuji prekompilovat kernel (jen pro optimalizaci, neni nutne):

General:
 PCI   Y
 Power Management Y
  (budto ACPI: Debug N; Bus Manager Y; Processor Y ...
  nebo APM

IDE, ATA, ATAPI:
  Generic PCI IDE Y
   Use DMA IDE  Y

  VIA82CXXX chipset Y

Char devices
 I2C support
  I2C support  M
  I2C device interface M
  I2C proc interface M
  ( + lm_sensors )

 /dev/agpart a  VIA chipset
    nemam poradne otestovano (na te PCI S3 to nejde)


Sound
 Sound card support M


USB support
 Support for USB   M
  preliminary USB filesystem  Y
  USB Controllers: UHCI (Intel,VIA) M

Poznámka

Pekne mala deska, pomerne vhodna na zvyseni vykonu AT stroje

stranky vyrobce "http://www.tigatech.com/tiga/ti-693a+.html"

provozuji jen s Celeronem (Coppermine), ale ma umet i P3 a Cyrix C3

zatim mi nejde full duplex sound (ovladac v jadre 2.4.18)
Full duplex rozchozen s ALSA

Dokument vytvořil: Petr Fuchs, 17.6.2002 10:55 | Zobrazeno: 1141×