Dotaz: sklamanie so SUSE 10.0 - suspend nefunkcny

[sykora]

Po nainštalovaní SUSE 10.0 nefunguje Suspend na disk, ani do RAM. Uklada a tvorí imag bez problemov, ale nevie sa z toho rezimu dostat. Do suspend to RAM ostava cierna obrazovka a to DISK zase rozmazane pozadie. Rad by som aby to fungovalo, ale beznajdená zalezitost uz niekolko rokov. Podla mňa ta technologia vyvoja je zlá a je ptrebne sa uberať iným smerom ako stále zdokonalovať to co funguje iba zlomku ludi. Napriklad co tak vytvorit virtualne zariadenie /dev/memory ktoré bude napájané aj po vypnutí ostatných castí. Ak by nekto vedel ako sa da spojazdnit ten suspend chcem to skusit. Instaloval som skript hibernate aj so zmenami v

 /etc/hibernate/ram.conf

potom spustil

hibernate -F /etc/hibernate/ram.conf

skusal som aj vbetool ale nic.

Ako je mozne zistit chybu. Kompilovat jadro nechcem. D

Odpovědi

[David Jaša]

Ako je mozne zistit chybu. Kompilovat jadro nechcem. D

Mě se bezproblémový suspend do RAM rozjel s 2.6.15. Do té doby mi to zamrzlo při probouzení, tak jsem používal ACPI S0 (standby).

Jinak pokud neuvedete typ notebooku, tak se na ten linux-laptop.net podívejte sám. A mimochodem včera tu byl vyřešen stejný problém. :-p

... ale beznajdená zalezitost uz niekolko rokov. Podla mňa ta technologia vyvoja je zlá a je ptrebne sa uberať iným smerom ako stále zdokonalovať to co funguje iba zlomku ludi. ...

Dejte to do blogu.

[sykora]

Tuna toto som copy, mozno mi niekto poradi, alebo dokaze najst chybu a odkaz na moj laptop je na webe linux on my compaq

linux:/home/ondro # dmesg |grep -i acpi
 BIOS-e820: 000000001bf70000 - 000000001bf7f000 (ACPI data)
 BIOS-e820: 000000001bf7f000 - 000000001bf80000 (ACPI NVS)
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6c90
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x1bf78eb1
ACPI: FADT (v001 ATI    Salmon   0x06040000 ATI  0x000f4240) @ 0x1bf7ef64
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x1bf7efd8
ACPI: DSDT (v001    ATI MS2_1535 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: local apic disabled
Kernel command line: auto BOOT_IMAGE=Linux ro root=303 selinux=0 resume=/dev/hda2 splash=silent acpi_sleep=s3_mode showopts noapic
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 0420)
ACPI: bus type pci registered
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 7 *10)
ACPI: PCI Interrupt Link [LNK2] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 7 *11)
ACPI: PCI Interrupt Link [LNK6] (IRQs 7 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs *5)
ACPI: PCI Interrupt Link [LNK8] (IRQs 7 *10)
ACPI: Embedded Controller [EC0] (gpe 24)
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNK6] -> GSI 10 (level, low) -> IRQ 10
ACPI wakeup devices:
ACPI: (supports S0 S3 S4 S5)
    ACPI-0212: *** Warning: Device is not power manageable
    ACPI-0402: *** Warning: Unable to derive IRQ for device 0000:00:10.0
ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (58 C)
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNK8] -> GSI 10 (level, low) -> IRQ 10
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNK7] -> GSI 5 (level, low) -> IRQ 5
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME
    ACPI-1048: *** Warning: Failed to acquire semaphore[db8e9ae0|1|0], AE_TIME