Dotaz: Wifi Broadcom a Fedora 5

[filbar]

Používám Fedoru 5 na notebooku HP nx6110 s wifi Broadcom BCM4306 802.11b/g a ani po instalaci ovladačů pomocí fwcutteru se me jí s ovladačem bcm43xx nedaří zprovoznit. Výpis z dmesg

eee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
bcm43xx driver
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 19
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243, disabled
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
ieee80211_crypt: registered algorithm 'WEP'
bcm43xx: set security called
bcm43xx:    .active_key = 0
bcm43xx:    .level = 1
bcm43xx:    .enabled = 1
bcm43xx:    .encrypt = 1
SoftMAC: net/ieee80211/softmac/ieee80211softmac_assoc.c:177:ieee80211softmac_assoc_work()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
SoftMAC: net/ieee80211/softmac/ieee80211softmac_assoc.c:177:ieee80211softmac_assoc_work()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: net/ieee80211/softmac/ieee80211softmac_assoc.c:177:ieee80211softmac_assoc_work()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: net/ieee80211/softmac/ieee80211softmac_assoc.c:177:ieee80211softmac_assoc_work()
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: net/ieee80211/softmac/ieee80211softmac_assoc.c:177:ieee80211softmac_assoc_work()
SoftMAC: Unable to find matching network after scan!
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 56/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512

Odpovědi

[vdusek]

Tento týden jsem to zprovozňoval pomocí ndiswrapperu a driverů pro Windows. Funguje mi to s EAP-PEAP, MSChapv2.

Je potřeba postupovat podle návodu na http://ndiswrapper.sourceforge.net/mediawiki/index.php/Installation - ndiswrapper jsem použil z rpmka (nepřekládal jsem ho, použil jsem 'binárku' Livna repo).

Windows driver jsem použil z http://ndiswrapper.sourceforge.net/mediawiki/index.php/List - pozor na správnou verzi

Návod na WPA je http://ndiswrapper.sourceforge.net/mediawiki/index.php/WPA

[vdusek]

Možná ještě jedna věc - mám

Network controller: Broadcom Corporation BCM4309 802.11a/b/g (rev 02)

[filbar]

S pomocí ndiswrapperu jsem to zprovoznil také. Jenomže já to potřebuji zprovoznit také s ovladačem bcm43xx, protože s pomocí ndiswrapperu nenastavím essid, který není vysílaný.

[vdusek]

Podle tohodle odkazu přece ničemu nevadí, ze SSID není broadcastované:

http://ndiswrapper.sourceforge.net/mediawiki/index.php/FAQ#I_can.27t_set_.28E.29SSID

Note that when setting the ESSID in Managed mode, the ESSID does not show up in iwconfig until the card has successfully associated with the access point!

Podle mne nijak ndiswrapper nesouvisí s iwconfig