Dotaz: divny zaznam v logu - vadny disk?

[Petr]

Ahoj

V logu jsem objevil nasledujicich par radek a nejsem si zcela jisty co to presne znamena. Mohli byste mi prosim poradit, co to znamena, co pripadne zkusit za nastroje abych mel jednoznacne podklady pro pripadnou reklamaci.

Vypis z logu /var/log/messages

May 15 20:22:16 Workstation kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
May 15 20:22:16 Workstation kernel: hda: drive_cmd: error=0x04 { AbortedCommand }
May 15 20:22:16 Workstation kernel: ide: failed opcode was: 0xef
May 15 20:22:16 Workstation kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
May 15 20:22:16 Workstation kernel: hda: drive_cmd: error=0x04 { AbortedCommand }
May 15 20:22:16 Workstation kernel: ide: failed opcode was: 0xef

Dik za kazdy tip

Odpovědi

[Jendа]

Zkusil bych SMART. Jinak podobné věci mi to házelo v dmesg, když jsem spouštěl Knoppix z poškrábaného CD
http://www.linuxexpres.cz/praxe/s-m-a-r-t-prorok-zlyhania-disku

[BigWrigley]

Jak již bylo řečeno, zjistit, co je ve S.M.A.R.T diagnostice disku, a co nejdříve zazálohovat! Možná prověřit kabel.

[AraxoN]

Mne to (alebo veľmi podobné) robilo pri niektorom staršom jadre - ak je viac ako rok staré, tak by som skúsil aktualizovať.

[jazz]

Souhlas, mně se jeden čas objevovalo v dmesg to samé, ale po aktualizaci jádra na 2.6.24 problém zmizel.
Toho, že je disk vadný, bych se nebál, protože by se hromadily chyby typu CRC Error nebo Read/Write Error.

[R]

To bude len nejaky nespravny prikaz, ktory disk odmietol (AbortedCommand).

[snajpa]

Me presne tohle hlaseni hazi kernel kdyz se snazim nastavit neco, co disk nepodporuje (u me konkretne regulace "hlasitosti disku"), muj disk je WDC400BB. Ale neprijde mi, ze by to melo vliv na dalsi funkcnost systemu.

[Petr Holík]

Jako prvni dulezita data hned zalohovat.

smartctl -t long /dev/hda a po nejakej dobe se podivat na smartctl -a /dev/hda a vlozit sem vysledek.

Zkontrolovat jestli je HW vse v poradku, dotlacit kabely.

a pak bych zkusil e2fsck -C0 -cc -v -f /dev/hda[cislo oddilu] a zkontroloval log, zda se hlaska obevi ve vetsim meritku.

Jinak ta hlaska nevesti nic dobreho, bud je spatne zapojenej kabel, nebo ten disk muze brzo odejit...

[sedlin]

Muzete mi nekdo mrknout, jestli je ten disk OK nebo ne? Diky.

smartctl -a /dev/hda

smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1600AAJB-00PVA0
Serial Number:    WD-WMAP99309052
Firmware Version: 00.07H00
User Capacity:    160�041�885�696 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sun Jun 29 18:02:21 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x85)	Offline data collection activity
					was aborted by an interrupting command from host.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 (4380) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  58) minutes.
Conveyance self-test routine
recommended polling time: 	 (   6) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       79
  3 Spin_Up_Time            0x0003   169   161   021    Pre-fail  Always       -       2525
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       143
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000e   200   200   051    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   094   094   000    Old_age   Always       -       4877
 10 Spin_Retry_Count        0x0012   100   100   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0012   100   100   051    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       142
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       64
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       143
194 Temperature_Celsius     0x0022   105   101   000    Old_age   Always       -       38
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   197   000    Old_age   Always       -       473
200 Multi_Zone_Error_Rate   0x0008   200   200   051    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 79 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 79 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 e9 02 12 e0  Error: UNC 8 sectors at LBA = 0x001202e9 = 1180393

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 e9 02 12 00 08      00:48:05.546  READ DMA EXT
  35 00 02 5f f7 19 01 08      00:48:05.546  WRITE DMA EXT
  35 00 06 59 f5 19 01 08      00:48:05.545  WRITE DMA EXT
  35 00 02 57 f3 19 01 08      00:48:05.545  WRITE DMA EXT
  35 00 02 55 f1 19 01 08      00:48:05.545  WRITE DMA EXT

Error 78 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 38 e9 02 12 e0  Error: UNC 56 sectors at LBA = 0x001202e9 = 1180393

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 38 e9 02 12 00 08      00:48:03.324  READ DMA EXT
  25 00 40 e1 02 12 00 08      00:48:01.417  READ DMA EXT
  25 00 48 d9 02 12 00 08      00:47:59.512  READ DMA EXT
  25 00 50 d1 02 12 00 08      00:47:57.281  READ DMA EXT
  25 00 58 c9 02 12 00 08      00:47:55.235  READ DMA EXT

Error 77 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 40 e1 02 12 e0  Error: UNC 64 sectors at LBA = 0x001202e1 = 1180385

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 40 e1 02 12 00 08      00:48:01.417  READ DMA EXT
  25 00 48 d9 02 12 00 08      00:47:59.512  READ DMA EXT
  25 00 50 d1 02 12 00 08      00:47:57.281  READ DMA EXT
  25 00 58 c9 02 12 00 08      00:47:55.235  READ DMA EXT
  25 00 60 c1 02 12 00 08      00:47:53.043  READ DMA EXT

Error 76 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 48 d9 02 12 e0  Error: UNC 72 sectors at LBA = 0x001202d9 = 1180377

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 48 d9 02 12 00 08      00:47:59.512  READ DMA EXT
  25 00 50 d1 02 12 00 08      00:47:57.281  READ DMA EXT
  25 00 58 c9 02 12 00 08      00:47:55.235  READ DMA EXT
  25 00 60 c1 02 12 00 08      00:47:53.043  READ DMA EXT
  25 00 68 b9 02 12 00 08      00:47:50.996  READ DMA EXT

Error 75 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 50 d1 02 12 e0  Error: UNC 80 sectors at LBA = 0x001202d1 = 1180369

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 50 d1 02 12 00 08      00:47:57.281  READ DMA EXT
  25 00 58 c9 02 12 00 08      00:47:55.235  READ DMA EXT
  25 00 60 c1 02 12 00 08      00:47:53.043  READ DMA EXT
  25 00 68 b9 02 12 00 08      00:47:50.996  READ DMA EXT
  25 00 70 b1 02 12 00 08      00:47:48.665  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      4877         -
# 2  Extended offline    Completed: read failure       90%      4453         1180399

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[Jan Šimák]

Toto je především problém:

# 2 Extended offline Completed: read failure 90% 4453 1180399

Spustil bych ručně "long" test a po jeho dokončení si jednak prohlédl log a pak také Reallocated_Sector_Ct; Raw_Read_Error_Rate; Current_Pending_Sector Pokud se jejich hodnoty oproti aktuálním zvýší, případně test skončí selháním, je disk 100% zralý na reklamaci.

[Jan Šimák]

další důležitý parametr, který musí být nulový je Reallocated_Event_Count, v opačném případě značí chybné sektory na disku.

[sedlin]

nemel by mi smart posilat nejaky varovani do mailu? nic mi neprislo...

[Jan Šimák]

To závisí na tom, jestli máš nainstalovaný smartd, jestli se spouští při startu, jak je nastaven ...

[azurIt]

hlupost, nemusi to byt nutne nulove. sem-tam sa moze nejaky sektor pokazit (a aj sa to deje, neznaci to vadny disk). samozrejme ak to cislo viditelne stupa, tak je to problem.

[sedlin]

to snad ani ne, disk mam asi 4 mesice!!! nemuze to byt jen neco, co se da softwarove opravit? Jinak tenhle test jsem spoustel, jak psal kolega vyse, vysledky jsem si prohledl za hodinu...

[sedlin]

A tady mam disk tyden stary... snad je ten aspon OK..

smartctl -a /dev/hdc

smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1600AAJB-00PVA0
Serial Number:    WD-WCAP99287092
Firmware Version: 00.07H00
User Capacity:    160�041�885�696 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sun Jun 29 22:15:34 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x85)	Offline data collection activity
					was aborted by an interrupting command from host.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 (4560) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  61) minutes.
Conveyance self-test routine
recommended polling time: 	 (   6) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   160   159   021    Pre-fail  Always       -       2983
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       42
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000e   200   200   051    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       53
 10 Spin_Retry_Count        0x0012   100   253   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0012   100   253   051    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       40
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       31
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       42
194 Temperature_Celsius     0x0022   104   103   000    Old_age   Always       -       39
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   051    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%        52         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[andree]

disky sa kazia aj rychlejsie ako po 4 mesiacoch (jeden moj raz posiel na vadne sektory po snad mesiaci...), kazdopadne ak si si isty ze 4 mesiace, tak ti asi v obchode predali naky pouzity disk:

Error 79 occurred at disk power-on lifetime: 4469 hours (186 days + 5 hours)

podla kopca tych read errorov by som na tom disku ale ziadne data radsej nedrzal a hodil im ho na reklamaciu asap.... (ten druhy disk vyzera, podla smart, ok)

ps: este mozes skusit spustit nejaky badblocks, ci to ten disk prezije... aspon zo 3x.. ak to zvladne, mozno s tebou este par dni bude schopny pobudnut..

[sedlin]

to je teda

je ten test stoprocentni? Aby mi ho z reklamace neposlali zpatky.. buh vi, jak to budou testovat...

[andree]

mno ja osobne by som ten disk nechcel - a urcite by som tam nenechaval dolezite data... tie chyby mozu najst aj v servise, ked si daju vypisat smartctl -a, takze ak je to aspon trochu seriozny obchod - povedz im, nech si to pozru atd...

mne taky disk napr. v mironet-e rovno vymenili (ked som im popisal, co v tom smart vypise bolo - ale ja som mal vadne sektory, no :)), kazdopadne osobne si myslim, ze na reklamaciu to je.. mozno nie su vadne datove plotny, "len" nejake spoje v elektronike - ale s tym sa asi aj tak neda nic robit :)

[sedlin]

A nemuze to byt treba vadny kabel?

[andree]

skus vymenit a spustit test znovu - uvidis z toho vypisu nie je moc lahke vypisat, kde presne medzi platnami a motherboardom je chyba :) ale keby smart vypisoval chyby o kabli, to by bolo dost divne, si myslim...

[Jan Šimák]

osobně jsem přesvědčen, že to co smart identifikuje se striktně týká pouze disku a nemá na to vliv kabeláž, řadič ...

[Mexiko]

jak už bylo psáno, pokud je to seriózní obchodník, tak reklamaci uzná. V jednom fileserveru jsem měl dva HDD a oba dva se po necelém měsíci provozu začaly chovat podivně. Poslal jsem je do reklamace i s výpisem ze smartclt a pomalu obratem (když pominu posel tam, víkend a posel zpět) mi přišly zpět dva nové disky.

[mato]

hm, nechcem kvoli tomuto zakladat nove vlakno, kedze moj problem je uzko spaty s podobnym problemom .. ja mam zase disk, ktory sice podla smartu nehlasi ziadne errory, ale hodnota Seek_Error_Rate stupa brutalne rychlo, vid:

  1 Raw_Read_Error_Rate     0x000f   112   100   006    Pre-fail  Always       -       46448051
  3 Spin_Up_Time            0x0003   094   094   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       16
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   062   060   030    Pre-fail  Always       -       4296657314
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       241
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       16
184 Unknown_Attribute       0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   063   056   045    Old_age   Always       -       37 (Lifetime Min/Max 35/40)
194 Temperature_Celsius     0x0022   037   044   000    Old_age   Always       -       37 (0 22 0 0)
195 Hardware_ECC_Recovered  0x001a   037   037   000    Old_age   Always       -       46448051
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       225         -
# 2  Extended offline    Completed without error       00%       222         -
# 3  Extended offline    Aborted by host               90%       220         -
# 4  Extended offline    Completed without error       00%        12         -

skusal som aj dd na cely disk, chybu nenasiel ziadnu .. pls, co si myslite na tento stav?

[andree]

povedal by som ze to bude ok tie cisla na konci su u niektorych diskov kus nedekodovatelne :)

[sedlin]

Tak jsem tady zase... disk mi vymenili, ale chyby pretrvaly... Vymenil jsem datovy kabel, nepomohlo... mam ted pocit, ze to dela napajeci kabel od zdroje... muze to byt tim? Nezda se mi, ze by mi poslali dalsi novej disk se stejnou vadou..:(

[sedlin]

nikdo nevite?

[AraxoN]

Príkaz uname -r napíše čo?

[sedlin]

mockrát děkuju za reakci. Příkaz vypíše 2.6.18-6-486. Mám na druhém řadiči totožný disk (RAID1) a problém s ním není...

[AraxoN]

A aj ten radič je totožný? Aký to je radič? Bolo by možné ten disk hodiť na iný radič a skúsiť tak?

... ale inak - 2.6.18 - to je tak november/december 2006, čo by zhruba korešpondovalo s tým, kedy sa mne takéto hlášky v logu zjavovali. Ako som už písal 2 mesiace dozadu, mne pomohol update jadra. Ak v distribúcii novšie jadro nie je, tak aj downgrade na staršie by mohol fungovať.

[sedlin]

Radic je primo na desce.. ted nemam uz momentalne pristup k serveru, tak nemuzu mrknout primo na typ..ale je asi 5 let stara... ten napajeci kablik na to nemuze mit vliv?

[AraxoN]

Kadečo môže mať vplyv na všeličo, to sa nedá vylúčiť... U mňa to bol integrovaný radič Intel ICH4, ktorý takto s jadrom nespolupracoval, ale neviem či sa tento bug v jadre týkal len jeho, alebo aj iných radičov. Typ radiča sa dá zistiť cez príkaz lspci. A to jadro by som zmenil už len kvôli bezpečnostným bugom, ktoré v ňom odvtedy boli objavené...

[sedlin]

no jo, tak budu zkouset... jinak nevim, proc mam tak stare jadro... porad aktualizuju co se da...

[faha]

jedno jsem se s obdovnou chybou setkal, dost mozna to ma neco spolecneho s DMA, server byl stejne urceny na vymenu, ale po zkusil jsem experimentalne pomoci hdparm vypnout DMA a chyby prestaly, ale neni to moc koser reseni...