Dotaz: Neustálé uspávání/vypínání disku

[Konqui]

Zdravím. Mám distribuci ArchLinux na notebooku a neustále se mi uspává disk. Neběží žádná power-save služba, ani laptop-mode.Disk se uspává tak co 30s na 1-5s, pak se zase roztočí, začal vypínat nedávno (jádro mám zkompilované 2.6.33 s CK patchsetem)

Výpis hdparm:

/dev/sda:

ATA device, with non-removable media
        Model Number:       ST9160821AS                             
        Serial Number:      5MA6K1FC            
        Firmware Revision:  3.BHE   
Standards:
        Supported: 7 6 5 4 
        Likely used: 8
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:  312581808
        Logical  Sector size:                   512 bytes
        Physical Sector size:                   512 bytes
        device size with M = 1024*1024:      152627 MBytes
        device size with M = 1000*1000:      160041 MBytes (160 GB)
        cache/buffer size  = 8192 KBytes
Capabilities:
        LBA, IORDY(can be disabled)
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 16
        Advanced power management level: 1
        Recommended acoustic management value: 254, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4 
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    SMART feature set
                Security Mode feature set
           *    Power Management feature set
                Write cache
           *    Look-ahead
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    DOWNLOAD_MICROCODE
           *    Advanced Power Management feature set
           *    48-bit Address feature set
           *    Device Configuration Overlay feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    IDLE_IMMEDIATE with UNLOAD
           *    Gen1 signaling speed (1.5Gb/s)
           *    Phy event counters
                Device-initiated interface power management
           *    Software settings preservation
           *    SMART Command Transport (SCT) feature set
Security: 
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
                supported: enhanced erase
        88min for SECURITY ERASE UNIT. 88min for ENHANCED SECURITY ERASE UNIT.
Checksum: correct

a S.M.A.R.T

smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 5400.3 series
Device Model:     ST9160821AS
Serial Number:    5MA6K1FC
Firmware Version: 3.BHE
User Capacity:    160 041 885 696 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Tue Jul  6 09:12:50 2010 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                 ( 426) seconds.
Offline data collection
capabilities:                    (0x53) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  88) minutes.
SCT capabilities:              (0x0001) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   100   006    Pre-fail  Always       -       67636253
  3 Spin_Up_Time            0x0002   099   099   000    Old_age   Always       -       0
  4 Start_Stop_Count        0x0033   096   096   020    Pre-fail  Always       -       4574
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   065   057   030    Pre-fail  Always       -       236406738248
  9 Power_On_Hours          0x0032   090   090   000    Old_age   Always       -       9206
 10 Spin_Retry_Count        0x0013   100   100   034    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0033   097   097   020    Pre-fail  Always       -       3434
184 End-to-End_Error        0x0032   100   253   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x003a   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0022   100   098   045    Old_age   Always       -       4295032842
189 High_Fly_Writes         0x0032   072   072   000    Old_age   Always       -       28
190 Airflow_Temperature_Cel 0x0032   062   041   000    Old_age   Always       -       38 (Lifetime Min/Max 38/38)
192 Power-Off_Retract_Count 0x0022   100   100   000    Old_age   Always       -       1138
193 Load_Cycle_Count        0x001a   001   001   000    Old_age   Always       -       549597
194 Temperature_Celsius     0x0012   038   059   000    Old_age   Always       -       38 (0 10 0 0)
195 Hardware_ECC_Recovered  0x0010   077   055   000    Old_age   Offline      -       52158282
197 Current_Pending_Sector  0x003e   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0000   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0000   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       925         -
# 2  Short offline       Completed without error       00%       923         -
# 3  Extended offline    Aborted by host               90%       275         -
# 4  Extended offline    Completed without error       00%       275         -
# 5  Short offline       Completed without error       00%       274         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Neví někdo co s tím?

---

---

Odpovědi

[zimous]

Vidim tam:
...
Advanced power management level: 1
...
Mozna by pomohlo:
hdparm -B 255
nebo
hdparm -S 0
Viz man hdparm.

[Ash]

Advanced power management level: 1
Recommended acoustic management value: 254, current value: 0

Zkusil bych pro power management (-B) a acoustic manatgement (-M) hdparm -B 254 -M 254 /dev/sda nebo -M 128, otázka je, co to nastavilo na 0.

[Konqui]

Tohle dělá nové pm-utils, už se to tu řešilo viz Dotaz: Upowerd mi zastavuje disky

snad pomůže

[Konqui]

Díky moc, to je asi ono, ještě to otestuju. A tomu buzerantovi, co tohle vymyslel, bych rozkopal hubu...

[luta]

není zač..já jsem přešel nakonec zpět na pm-utils 1.3 neměl jsem náladu řešit proč zase blbne suspend