Dotaz: WIFI na Lubuntu HP ComPAQ

[JohnCenaWWE]

Ahojte poradte mi nejaky jednoduchy program/aplikaciu/ na spustenie WIFI na Lubuntu 14.04 pripadne na linuxMint17 na mojom notebooku som si nainstaloval driver B43 na WIFI ale neviem to spojazdnit skusam secko

iwconfigwlan0     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=off   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
          
lo        no wireless extensions.

eth0      no wireless extensions.

iwlist scanwlan0     Failed to read scan data : Network is down

lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

nieco z vypisov

---

---

Odpovědi

[JohnCenaWWE]

sudo ip link set wlan0 up
[sudo] password for johncenawwe: 
RTNETLINK answers: Operation not possible due to RF-kill

[Love_Dali]

hmm, zkusím třeba: https://bbs.archlinux.org/viewtopic.php?id=173808 resp. https://bbs.archlinux.org/viewtopic.php?pid=1324810#p1324810

[NN]

Na liste mas menu pro pripojeni.

[JohnCenaWWE]

rfkill list all0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: yes

skusam aj WICD ale nemozem zapnut WIFI tl.na klavesnici,pri starte mi blikne modra pod tl. ale nejde zapnut ani cez terminal

[k3dAR]

Hard blocked je Hardwarove blokovane, takze WICD, NetworkManager, to aktivovat nemuzou... musis vyresit proc ti nejde HW tlacitko na on/off wifi... coz dost mozna je ten druhej odkaz od Love_Dali, to si zkousel???

[JohnCenaWWE]

jasne uz sa s tym trapim 4h ale to # echo "blacklist hp_wmi" > /etc/modprobe.d/hp.conf

HP_WMI tam nemam

[k3dAR]

nevim jestli chapes, to echo tam nemas, to je jen pro zapsani radku

blacklist hp_wmi

do souboru

/etc/modprobe.d/hp.conf

aby se nenatahoval ten ovladac, ted koukam ze se spravne jmenuje hp-wmi a na hp_wmi je odkaz jen v aliasech, kazdopadne muzes pridat blacklist radek radeji i pro hp-wmi, pak restartovat a overit ze to nemas natazene:

lsmod | grep -e hp_wmi -e hp-wmi

[JohnCenaWWE]

Příloha:

• hpp.png (37345 bytů)

ten subor hp.conf tam nemam

[Pavel 'TIGER' Růžička]

... tak ho musíš vytvořit.

[JohnCenaWWE]

vytvoril som hp.conf a do neho som napisal iba blacklist hp_wmi ,reboot,a nic stale

[Pavel 'TIGER' Růžička]

Tak terminál a potom: rfkill unblock all

[Pavel 'TIGER' Růžička]

... pochopitelně jako sudo!

[JohnCenaWWE]

sudo rfkill unblock all
[sudo] password for johncenawwe: 
johncenawwe@johncenawwe-HP-Compaq-nx6325-EY352EA-AKR:~$ rfkill list
0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: yes

[k3dAR]

tady je jasne videt ze modul natahlej mas...
pro jistotu dej vystup (btw: ten radek echo kdyz bys prvne pouzil tak ten soubor vytvari automaticky kdyz nebyl):

cat /etc/modprobe.d/hp.conf

proste dokud po restartu budes mit natahle hp_wmi tak ho nemas blokovane, takze az ti

lsmod | grep -e hp_wmi -e hp-wmi

nezobrazi nic, tak teprve mas blokovanej modul hp_wmi a prijde na radu:

sudo rfkill unblock all

jako nerucim(e) ze to je ono, ale zavrhnout to jen proto ze se ti nedari(?) bloknout modul je moc brzo :)

[JohnCenaWWE]

dik dal som secko ako pises restart a neukazalo mi nic ani po rfkill dalo novy riadok ked dam list zase HARD blocked

[JohnCenaWWE]

sudo ifconfig wlan0 up
[sudo] password for johncenawwe: 
SIOCSIFFLAGS: Operace není možná kvůli zakázanému rádiu (RF-kill)

[Pavel 'TIGER' Růžička]

Ahoj, a máš v biosu povolenou WiFi při zapnutí notebooku?

[JohnCenaWWE]

Příloha:

• Fotografia-2163.jpg (16309 bytů)

kuk obr. inak mam dual boot a vo winXP WIFI ide

[NN]

Kdyz uz tam jses vypni ten switching, a wake on LAN..

[JohnCenaWWE]

0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: yes

hosi tu bude pes zakopany,ale ani za toho oneho neviem ako to spojazdnit a ten HADR blocked dat na NO,uz som precital kvantum toho ale neviem co stym poradte ako to spojazdnit prosim

sudo ip link set wlan0 up
RTNETLINK answers: Operation not possible due to RF-kill

[petertomasy]

skús odpojiť 220 V a vybrať batériu na niekoľko minúť, takáto finta niekedy pomôže ...

[polovod]

A notes hodit do popelnice,to taky hodně pomáhá.

[Pavel 'TIGER' Růžička]

Zkus: sudo rmmod b43
sudo modprobe b43
sudo rfkill list

[JohnCenaWWE]

johncenawwe@johncenawwe-HP-Compaq-nx6325-EY352EA-AKR:~$ sudo rmmod b43
johncenawwe@johncenawwe-HP-Compaq-nx6325-EY352EA-AKR:~$ sudo modprobe b43
johncenawwe@johncenawwe-HP-Compaq-nx6325-EY352EA-AKR:~$ sudo rfkill list 
1: phy1: Wireless LAN
	Soft blocked: no
	Hard blocked: yes

[MadCatX]

Podívej se, jaké WMI moduly jsou vlastně zavedené, může v tom občas být dost chaos

lsmod | grep wmi

Jestli tam je WiFi od Broadcomu a zavedený modul b43, nechybí té kartě jen firmware?

[JohnCenaWWE]

snd_rawmidi            25135  1 snd_seq_midi
snd_seq_device         14137  3 snd_seq,snd_rawmidi,snd_seq_midi
snd                    60871  16 snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_analog,snd_seq_midi

[MadCatX]

Žádný další WMI modul tam zjevně není, OK. Teď je tedy otázka, co je tam za WiFi kartu, jaký se pro ni používá ovladač a jestli není potřeba doinstalovat balíček s firmwarem.

[k3dAR]

bez informaci/naslepo, mozna je to klasickej b43 problem jehoz resenim je tohle

[k3dAR]

jinak ty informace:

# detailni info o pci zarizeni
sudo lspci -vnn

# o usb zarizeni
lsusb -v

# a z logu (tak nekdy rozumne brzo po startu/rebootu):
dmesg | grep -i -e network -e wifi -e wireless -e firmware -e b43 -e bcm -e network -B1 -A3

[JohnCenaWWE]

30:00.0 Network controller [0280]: Broadcom Limited BCM4311 802.11a/b/g [14e4:4312] (rev 01)
	Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1361]
	Flags: bus master, fast devsel, latency 0, IRQ 18
	Memory at c8000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [40] Power Management version 2
	Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [d0] Express Legacy Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [13c] Virtual Channel
	Kernel driver in use: b43-pci-bridge

dmesg | grep -i -e network -e wifi -e wireless -e firmware -e b43 -e bcm -e network -B1 -A3
[    0.116485] ACPI: No dock devices found.
[    0.116896] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    0.116920] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[    0.120013] ACPI: Power Resource [C22D] (off)
[    0.120934] ACPI: Power Resource [C204] (off)
[    0.121782] ACPI: Power Resource [C221] (on)
--
[    2.816414] tg3.c:v3.134 (Sep 16, 2013)
[    2.891166] tg3 0000:02:01.0 eth0: Tigon3 [partno(BCM95788A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:17:a4:ce:dd:1f
[    2.891175] tg3 0000:02:01.0 eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0])
[    2.891179] tg3 0000:02:01.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.891182] tg3 0000:02:01.0 eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
--
[   25.424209] cfg80211: Calling CRDA to update world regulatory domain
[   25.539168] [Firmware Bug]: _BCQ is used instead of _BQC
[   25.539185] ACPI: Video Device [C07B] (multi-head: yes  rom: no  post: no)
[   25.539203] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[   25.560982] parport_pc 00:01: [io  0x0378-0x037f]
[   25.560993] parport_pc 00:01: [io  0x0778-0x077a]
[   25.561088] parport_pc 00:01: [irq 7]
[   25.561094] parport_pc 00:01: [dma 1]
[   25.562101] b43-phy0: Broadcom 4311 WLAN found (core revision 10)
[   25.583379] acpi device:03: registered as cooling_device5
[   25.583539] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/LNXVIDEO:00/input/input9
[   25.589025] parport_pc 00:01: activated
--
[   25.589116] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   25.604066] b43-phy0: Found PHY: Analog 4, Type 2 (G), Revision 8
[   25.631229] Broadcom 43xx driver loaded [ Features: PNL ]
[   25.654302] wmi: Mapper loaded
[   25.667477] ppdev: user-space parallel port driver
--
[   26.965448] type=1400 audit(1485095037.900:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=452 comm="apparmor_parser"
[   26.965462] type=1400 audit(1485095037.900:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=452 comm="apparmor_parser"
[   26.965469] type=1400 audit(1485095037.900:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=452 comm="apparmor_parser"
[   26.966212] type=1400 audit(1485095037.900:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=452 comm="apparmor_parser"
[   26.966222] type=1400 audit(1485095037.900:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=452 comm="apparmor_parser"
[   26.966593] type=1400 audit(1485095037.900:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=452 comm="apparmor_parser"
[   26.994583] type=1400 audit(1485095037.928:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=454 comm="apparmor_parser"
--
[   29.270817] input: HDA ATI SB Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input16
[   31.872066] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[   31.956384] b43-phy0: Radio hardware status changed to DISABLED
[   31.964042] b43-phy0: Radio turned on by software
[   31.964047] b43-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
[   31.966950] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   32.032915] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   32.514537] init: samba-ad-dc main process (745) terminated with status 1

[JohnCenaWWE]

hosi tak sa tu trapime viacej dni a pes bol zakopany v BIOSE,na zahr.fore som sa docital cennu radu v BIOSE som dal Restore Defaults,save F10,reboot a WIFI uz ide parada diki vsetkym za pomoc a cenne rady

0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no

[Jan Bek]

Zdarec, mně se totéž stalo na Compaqu 6710b. Po odstranění Windows a Instalaci SUSE Leap 15.1 taky bylo nutno nastavit bios do továrního nastavení. Taková blbost. Hlavně, že po zkoušení různého nastavení ovladačů hodil jeden z diskutérů odkaz natoto vlákno. Díky všem za pomoc.

[mart]

tak jako dalsi v rade.. po celem dni zoufalstvi, take pomohl bios do tovarniho nastaveni..

dell latitude E 5470.

dekuji za nakopnuti