Dotaz: ako zistim ramku vga karty

[mirec]

dobry,,,rano.....je nejaky sposob ako zisitit ramku vga karty cez konzolu?????

Odpovědi

[pasmen]

lspci -v nebo nekde v /proc

[Zdeněk Štěpánek]

Zdravim

Lspci -v mi teda u 4MB karty prozradilo 16MB a u 16MB ukazalo 32MB, takze zjevne jsou to uplne jiny pamety nez ty na graficce.

Presne to zjistis v logo X.org.

Zdenek

[Petr Šobáň]

Mě to ukázalo správnou velikost

01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200 AGP 8x] (rev a1) (prog-if 00 [VGA])
Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 11
Memory at ce000000 (32-bit, non-prefetchable) [size=cfee0000]
Memory at c0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at 00020000 [disabled]

nezapočítalo to tam náhodou i ram z MB kterou může karta použít ?

[pasmen]

Hmm, me to u tri karet co mam doma (Riva TNT2, Trident CyberBlade i1, S3 Virge) ukazuje tak jak ma, zajimave. Samozrejme ti lspci -v nevypisuje jen fyzickou videoram, ta byva vetsinou uvedena jako posledni region (pri lspci -vv). Nevim, jake jine pameti by to vypisovalo. Z logu XOrg to zjistis, pravda, ale autor dotazu nejspis chtel zjistit tu velikost bez X.

[Zdeněk Štěpánek]

Zdravim

Ani lspci -vv nepomohlo:

4MB PCI karta:

00:09.0 VGA compatible controller: Rendition Verite V2000/V2100/V2200 (rev 06) (prog-if 00 [VGA])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium )TAbort- (TAbort- (MAbort- )SERR- (PERR-
        Latency: 32, cache line size 08
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at ea000000 (32-bit, prefetchable) [size=16M]
        Region 1: I/O ports at a000 [size=256]
        Region 2: Memory at ec000000 (32-bit, non-prefetchable) [size=256K]
        Expansion ROM at (unassigned) [disabled] [size=128K]

16MB AGP karta:

01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF/SG AGP (prog-if 00 [VGA])
        Subsystem: ATI Technologies Inc Magnum/Xpert 128/Xpert 99
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium )TAbort- (TAbort- (MAbort- )SERR- (PERR-
        Latency: 32 (2000ns min), cache line size 08
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
        Region 1: I/O ports at 9000 [disabled] [size=256]
        Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=16K]
        Expansion ROM at (unassigned) [disabled] [size=128K]
        Capabilities: [50] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=(none)
        Capabilities: [5c] Power Management version 1
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Zdenek

[Antonín Kolísek]

zkus třeba cat /var/log/XFree86.0.log | grep VideoRAM

[mirec]

ok dik vsetci......no myslel som prave tu moznost ked nemam Xka...tak ze jedina moznost je lspci.... este raz dikx

[David Jež]

Jeste je jeden zpusob, nebo vlastne dva. Pro sikovnejsi oko, pro slabozrake lupa .
-djz