SupraFAX 288i PnP

Ovladač:

v jádře

Technické parametry

Rychlost faxu (Class 1,2) az 14400, modemu az 28800.
Protokoly: ITU-TSS V.34 / V.FC / V.32bis / V.32 / V.22 / V.22bis / V.21 / Bell 103/212A
Opravne a kompresni protokoly: ITU-TSS V.42bis / V.42 / MNP 2-5.
Emulace UART 16550. Max DTE-DCE rychlost 115200. Flash ROM, modem lze po HW uprave upgradovat na 33.6.

Identifikace pod Linuxem

ati3:

====

V1.200-07-V34_DP

SupraFAXModem 288i PnP

Built: July 20 1995 14:40:06

Vypis prostredku pomoci pnpdump

# $Id: pnpdump.c,v 1.21 1999/12/09 22:28:33 fox Exp $
# Release isapnptools-1.21b (library isapnptools-1.21b)
#
# Trying port address 0273
# Board 1 has serial identifier 66 00 00 27 be 90 12 b0 4e

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 66 00 00 27 be 90 12 b0 4e)
# Vendor Id SUP1290, Serial Number 10174, checksum 0x66.
# Version 1.0, Vendor version 0.0
# ANSI string -->SupraFAXModem 288i PnP Modem<--
#
# Logical device id SUP1290
#     Device supports I/O range check register
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3d
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE SUP1290/10174 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK))
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK))
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK))
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK))
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK))
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
#       IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#     End dependent functions
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

Postup zprovoznění pod Linuxem

Pri inicializaci PnP vypnout kontrolu volnych prostredku IO, jinak hlasi konflikt.

Tedy napr.:

Zprovozneni:
===========

Modem se chova jako korektni PnP karta.
Prostredky, na kterych je ochotna pracovat jsem
ziskal z vypisu pnpdump (viz nize).

Do konfiguracniho souboru isapnp (aka /etc/isapnp.conf
u RedHat 6.2) je treba tu spravnou nekonfliktni
z voleb (viz napr. /proc/interrupts a /proc/ioports
ohledne konfigurace zarizeni).

Rekneme, ze si vyberu konfiguraci IRQ 12, port 0x02e8.
Potom do isapnp.conf prijde:

(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)

(CONFIGURE SUP1290/10174 (LD 0
(IO 0 (SIZE 8) (BASE 0x02e8))
(INT 0 (IRQ 12 (MODE +E)))
(NAME "SUP1290/10174[0]{SupraFAXModem 288i PnP Modem}")
(ACT Y)
))

(WAITFORKEY)

Tedy vyjmul jsem (CHECK) a vybral IRQ 12
(jinak to jedna z tech moznych konfiguraci nize).
Pomoci isapnp muzeme konfiguraci aktivovat:

$ isapnp /etc/isapnp.conf
Board 1 has Identity 66 00 00 27 be 90 12 b0 4e:  SUP1290 Serial No 10174 [checksum 66]
SUP1290/10174[0]{SupraFAXModem 288i PnP Modem}: Port 0x2E8; IRQ12 --- Enabled OK

A co zbyva? Pres setserial nastavit, kam ho chceme (tady na COM4):

$ setserial /dev/ttyS3 irq 12 port 0x02e8 autoconfig
/dev/ttyS3, UART: 16550A, Port: 0x02e8, IRQ: 12

Poznámka

Dokument vytvořil: Miroslav BENES, 26.3.2000 12:43 | Zobrazeno: 992×