Dotaz: výměna CD-ROM za disk

[multi]

Zdar
Nainstaloval jsem si doma na starší PC Madrake 9.2 CD-ROMku jsem pak vyndal a když jsem tam dal disk tak ho linux nepoužil.
Bios Disk najde a je vpořádku . Neni ani na něj ani odkaz /etc/hdb
Disk je jako slave na jednej kšandě s jinym (bokužel mam jen jednu kšandu).
Nemůžeto bejt tim, že jádro předpokládá že tam bude CD-ROMka?

Odpovědi

[sewi]

Vlož sem výpis

/proc/partitions

a

/etc/fstab

[Zdeněk Štěpánek]

Zdravim

Jadru je to jedno, ostatne dmesg ti jistojiste prozradi ze to nasel jako harddisk, spis to nejak nepobral ten mandrako coz je tedy divny. Zkus v MDKCC najit neco jako pripojna mista, body pripojeni nebo tak neco. Mozna pomuze jako root spustit kudzu, aspon v redhatu je kudzu na hledani noveho HW.

Zdenek

[HynaDJ]

Tak ten hadr pokud jsi to spletl by měl byt v /dev/hdb (ne /etc/hdb), pokud tam byla dřív ta cdromka. Když jsem do počítaču přidal cdromku, tak se mě v mandraku při startu spouštěl průvodce který mě dal vybrat, kam chcu tů cdromku připojit... snát to tam take máš.

[NFT]

Vo vypise som si vsimol /dev/hdb=ide-scsi, mal by si ho tym padom montovat ako scsi zariadenie (/dev/scd[x]). alebo odstranit (pravdepodobne z lilo.conf ak pouzivas lilo) zmienku o tom ze /dev/hdb je scsi

[multi]

samozřejmě tam má být /dev/hdb
problém je, že to zařízení neexistuje

[Martin Beránek]

komu neni rady, tomu neni pomoci...

koukni na /proc/partitions a na dmesg

[multi]

v /proc/partitions neni

dmesg
Linux version 2.4.22-10mdk (nplanel@no.mandrakesoft.com) (gcc version 3.3.1 (Mandrake Linux 9.2 3.3.1-2mdk)) #1 Thu Sep 18 12:30:58 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000002000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
32MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 8192
zone(0): 4096 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
DMI not present.
ACPI: Unable to locate RSDP
Building zonelist for node : 0
Kernel command line: root=/dev/hda1 devfs=mount hdb=ide-scsi
resume=/dev/hda5 splash=silent vga=785
ide_setup: hdb=ide-scsi
bootsplash: silent mode.
No local APIC present or hardware disabled
Initializing CPU#0
Detected 167.048 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 333.41 BogoMIPS
Memory: 28692k/32768k available (1508k kernel code, 3688k reserved,
-1961k data, 156k init, 0k highmem, 0k BadRAM)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Intel Pentium with F0 0F bug - workaround enabled. CPU: After generic, caps: 008001bf 00000000 00000000 00000000
CPU: Common caps: 008001bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20030813
PCI: PCI BIOS revision 2.10 entry at 0xfda01, last bus=0
PCI: Using configuration type 1
ACPI: System description tables not found
ACPI-0084: *** Error: acpi_load_tables: Could not get RSDP, AE_NOT_FOUND
ACPI-0134: *** Error: acpi_load_tables: Could not load tables: AE_NOT_FOUND
ACPI: Unable to load the System Description Tables
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: Card 'OPL3-SAX Sound Board'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0xfc000000, mapped to 0xc2800000, size 1200k
vesafb: mode is 640x480x16, linelength=1280, pages=2
vesafb: protected mode interface info at c000:7ea0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC2850F, ATA DISK drive
hdb: WDC AC2200F, ATA DISK drive
blk: queue c0180d20, I/O limit 4095Mb (mask 0xffffffff)
hdb: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdb: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 1 didn't accept speed setting. Oh, well.
hdb: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdb: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 1 didn't accept speed setting. Oh, well.
blk: queue c0180e5c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 1667232 sectors (854 MB) w/64KiB Cache, CHS=827/32/63, DMA
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdb:<6>end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 1
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 3
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 5
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 7
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 1
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 3
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 5
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 7
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483640
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483641
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483642
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483643
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483644
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483645
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483640
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483641
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483642
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483643
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483644
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483645
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
unable to read partition table
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Resume Machine: This is normal swap space
Swsusp 1.0.3: kswsuspd starting
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 89k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
Real Time Clock Driver v1.10e
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 76568k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xc2995f00, 00:11:3b:01:7d:ff, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
inserting floppy driver for 2.4.22-10mdk
FDC 0 is a post-1991 82077
i2c-core.o: i2c core module version 2.8.0 (20030714)
i2c-proc.o version 2.8.0 (20030714)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

cat /proc/partitions
major minor #blocks name rio rmerge rsect ruse wio wmerge wsect wuse running use aveq
3 0 833616 ide/host0/bus0/target0/lun0/disc 3949 6005 79466 95240 608 1810 19392 45250 -1 508020 42529052
3 1 756976 ide/host0/bus0/target0/lun0/part1 3920 5879 78386 94130 482 529 8128 30530 0 75970 124660
3 2 1 ide/host0/bus0/target0/lun0/part2 0 0 0 0 0 0 0 0 0 0 0
3 5 76576 ide/host0/bus0/target0/lun0/part5 25 106 1048 1020 126 1281 11264 14720 0 5450 15740
3 64 1073741823 hdb 7 33 52 120 0 0 0 0 0 120 120

[multi]

dmesg
Linux version 2.4.22-10mdk (nplanel@no.mandrakesoft.com) (gcc version 3.3.1 (Mandrake Linux 9.2 3.3.1-2mdk)) #1 Thu Sep 18 12:30:58 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000002000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
32MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 8192
zone(0): 4096 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
DMI not present.
ACPI: Unable to locate RSDP
Building zonelist for node : 0
Kernel command line: root=/dev/hda1 devfs=mount hdb=ide-scsi
resume=/dev/hda5 splash=silent vga=785
ide_setup: hdb=ide-scsi
bootsplash: silent mode.
No local APIC present or hardware disabled
Initializing CPU#0
Detected 167.048 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 333.41 BogoMIPS
Memory: 28692k/32768k available (1508k kernel code, 3688k reserved,
-1961k data, 156k init, 0k highmem, 0k BadRAM)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Intel Pentium with F0 0F bug - workaround enabled. CPU: After generic, caps: 008001bf 00000000 00000000 00000000
CPU: Common caps: 008001bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20030813
PCI: PCI BIOS revision 2.10 entry at 0xfda01, last bus=0
PCI: Using configuration type 1
ACPI: System description tables not found
ACPI-0084: *** Error: acpi_load_tables: Could not get RSDP, AE_NOT_FOUND
ACPI-0134: *** Error: acpi_load_tables: Could not load tables: AE_NOT_FOUND
ACPI: Unable to load the System Description Tables
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: Card 'OPL3-SAX Sound Board'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0xfc000000, mapped to 0xc2800000, size 1200k
vesafb: mode is 640x480x16, linelength=1280, pages=2
vesafb: protected mode interface info at c000:7ea0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC2850F, ATA DISK drive
hdb: WDC AC2200F, ATA DISK drive
blk: queue c0180d20, I/O limit 4095Mb (mask 0xffffffff)
hdb: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdb: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 1 didn't accept speed setting. Oh, well.
hdb: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdb: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 1 didn't accept speed setting. Oh, well.
blk: queue c0180e5c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 1667232 sectors (854 MB) w/64KiB Cache, CHS=827/32/63, DMA
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdb:<6>end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 1
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 3
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 5
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 7
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 1
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 3
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 5
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 7
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483640
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483641
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483642
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483643
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483644
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483645
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483640
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483641
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483642
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483643
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483644
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2147483645
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 0
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 2
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 4
end_request: I/O error, cmd 0 dev 03:40 (hdb), sector 6
unable to read partition table
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Resume Machine: This is normal swap space
Swsusp 1.0.3: kswsuspd starting
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 89k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
Real Time Clock Driver v1.10e
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 76568k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xc2995f00, 00:11:3b:01:7d:ff, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
inserting floppy driver for 2.4.22-10mdk
FDC 0 is a post-1991 82077
i2c-core.o: i2c core module version 2.8.0 (20030714)
i2c-proc.o version 2.8.0 (20030714)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

cat /proc/partitions
major minor #blocks name rio rmerge rsect ruse wio wmerge wsect wuse running use aveq
3 0 833616 ide/host0/bus0/target0/lun0/disc 3949 6005 79466 95240 608 1810 19392 45250 -1 508020 42529052
3 1 756976 ide/host0/bus0/target0/lun0/part1 3920 5879 78386 94130 482 529 8128 30530 0 75970 124660
3 2 1 ide/host0/bus0/target0/lun0/part2 0 0 0 0 0 0 0 0 0 0 0
3 5 76576 ide/host0/bus0/target0/lun0/part5 25 106 1048 1020 126 1281 11264 14720 0 5450 15740
3 64 1073741823 hdb 7 33 52 120 0 0 0 0 0 120 120

[popelari]

udělejte disku "Pá pá...!" a vložte do takového toho co vám stojí za domem... až přijedou opraváři, tak si s tím poradí...

PS: pokud je v záruce, tak reklamujte radši u prodavače než u popeláře

[vencour]

Kdyby byl špatně naswitchovanej, mohlo by to dělat to samý? Teoreticky ... tj. při souhře náhod by šel jeden disk a druhý ne. Případně s tím druhým diskem nechodí? Jako kdysi western a seagate? Tj. nemusí být ještě K.O.? Nebo nemá šťávu a nerozjede se, proto není dostupný = slabý zdroj, vadné kabely?

[ten co před tím]

...aneb tonoucí se stébla chytá. no možný to je... ale sázky budou asi jinde

[sewi]

Kdyz na nej chytnes tak poznas jestli se toci, switchovani muze delat problemy, od toho jsou na disku ty labely s obrazkama kam ten switch ma prijit.

[vencour]

Nebo ho zapojit jako single a buď se rozjede a třeba tam bude "MISSING OS" nebo se nechytne a bude tam třeba "I/O error". Když už ne nějaký live distro/disketu.

[ide-scsi]

Co to tu furt řešíte za kraviny. Vyhoď především z konfigurace lila nebo grubu tu emulaci SCSI. Pak se ti to nejspíš rozjede samo.

[multi]

njn
máš pravdu hned to zabral moc dik za radu
ta emulace tam byla kvůli tý CD-ROMce?

[vend]

Jo jo. To oni si Mamtáci dělaj fóra, kdybys tam náhodou dal vypalovačku.

Není nad to, když si distribuce myslí, že je chytřejší než ty

[multi]

Mam ještě jeden dotaz.
Nainstaloval jsem si tam ješte grafícký prostředí (iceWM, fluxbox, blacbox), ale velikost písma je tak malá (a to ve všech desktopech), že se tam nedá pracovat.
Tak by mě zajmalo v jakym konfiguráku můžu změnit velikost.