Dotaz: Zamrznutí na SUSE (Bylo: prej si neco, pada suse...)

[jozka]

Presneji receno zamrzne. Z vteriny na vterinu prestane reagovat na mys, klavesnici... Je to trest za to, ze jsem fungujici 10.3 vymenil za 11.0 (oboje 64 bit). Aktualizace se nepovedla, takze jsem udelal cistou instalaci. Po instalaci, ktera vytvorila systemovou a datovou partition jsem tu druhou jmenovanou odpojil a rucne pripojil cely druhy disk, kde jsem mel data. Muze to byt zdroj problemu? Ve /var/log/messages jsem v okamzicich padu nic podezreleho nenasel, snad jen vice hlasek, ktere podle meho mlhaveho povedomi souvisi se S.M.A.R.T, ale zatim tam nepoznam, co je bezny provoz a co je problem Pocitac normalne fungoval s 10.3, problemy nastaly ihned po prechodu na 11.0 a pokud nouzove pouziju knoppix, tak funguje taky normalne. Nemate prosim nekdo nejaky napad co s tim?

Odpovědi

[Bluebear]

Po instalaci, ktera vytvorila systemovou a datovou partition jsem tu druhou jmenovanou odpojil a rucne pripojil cely druhy disk, kde jsem mel data. Muze to byt zdroj problemu?

To snad ne.

Pokud se ve /var/log/messages objevují hlášky související se SMARTem, tak je možné, že se s tebou loučí disk (zálohovat!). Můžeš-li, uveď vzorek.

Pozoroval jsi ještě i jiné netypické chování? Používáš opensourcový nebo proprietární video driver? Pokud proprietární, můžeš to na chvíli zkusit s opensourcovým, jestli se to nebude chovat jinak.

Ale obecně, náhlé zatuhnutí počítače IMHO napovídá na chybu hardwaru - zkus test paměti (memchk je tuším na openSUSE DVD).

[jozka]

Disk je novy (z letoska). HW taky vedu jako mozneho vinika, ale ze by byl alergicky jen na 11.0 a na nic jineho ne?

S tim SMARTEM:

Jun 24 22:17:08 linux-5na9 smartd[3050]: Device: /dev/sda, SMART Prefailure Attribute: 1 Raw_Read_Error_Rate changed from 253 to 100
Jun 24 22:17:08 linux-5na9 smartd[3050]: Device: /dev/sda, SMART Usage Attribute: 190 Airflow_Temperature_Cel changed from 72 to 65
Jun 24 22:17:08 linux-5na9 smartd[3050]: Device: /dev/sda, SMART Usage Attribute: 194 Temperature_Celsius changed from 154 to 130
Jun 24 22:17:08 linux-5na9 smartd[3050]: Device: /dev/sda, SMART Usage Attribute: 200 Multi_Zone_Error_Rate changed from 253 to 100
Jun 24 22:17:08 linux-5na9 smartd[3050]: Device: /dev/sdb, SMART Usage Attribute: 194 Temperature_Celsius changed from 35 to 43

Tohle je posledni start systemu, kdy to vytuhlo chvilicku najeti KDE:

Jun 24 22:32:19 yetti syslog-ng[1678]: syslog-ng version 1.6.12 starting
Jun 24 22:32:20 yetti rchal: CPU frequency scaling is not supported by your processor.
Jun 24 22:32:20 yetti rchal: boot with 'CPUFREQ=no' in to avoid this warning.
Jun 24 22:32:20 yetti rchal: Cannot load cpufreq governors - No cpufreq driver available
Jun 24 22:32:21 yetti SuSEfirewall2: batch committing...
Jun 24 22:32:21 yetti SuSEfirewall2: Firewall rules set to CLOSE.
Jun 24 22:32:23 yetti ifup:     lo        
Jun 24 22:32:23 yetti ifup:     lo        
Jun 24 22:32:23 yetti ifup: IP address: 127.0.0.1/8  
Jun 24 22:32:23 yetti ifup:  
Jun 24 22:32:23 yetti ifup:               
Jun 24 22:32:23 yetti ifup: IP address: 127.0.0.2/8  
Jun 24 22:32:23 yetti ifup:  
Jun 24 22:32:23 yetti ifup:     eth0      device: nVidia Corporation CK8S Ethernet Controller (rev a2)
Jun 24 22:32:23 yetti ifup:               No configuration found for eth0
Jun 24 22:32:24 yetti ifup:     eth1      device: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Jun 24 22:32:24 yetti ifup-dhcp:     eth1      (DHCP) 
Jun 24 22:32:24 yetti ifup-dhcp: . 
Jun 24 22:32:24 yetti dhcpcd[2250]: eth1: dhcpcd 3.2.3 starting
Jun 24 22:32:24 yetti dhcpcd[2250]: eth1: hardware address = 00:11:09:da:f0:16
Jun 24 22:32:24 yetti dhcpcd[2250]: eth1: broadcasting for a lease
Jun 24 22:32:24 yetti dhcpcd[2250]: eth1: offered 192.168.10.142 from 192.168.10.1
Jun 24 22:32:24 yetti dhcpcd[2250]: eth1: checking 192.168.10.142 is available on attached networks
Jun 24 22:32:24 yetti kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jun 24 22:32:24 yetti kernel: NET: Registered protocol family 10
Jun 24 22:32:24 yetti kernel: lo: Disabled Privacy Extensions
Jun 24 22:32:24 yetti kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jun 24 22:32:24 yetti kernel: powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (1 cpu cores) (version 2.20.00)
Jun 24 22:32:24 yetti kernel: ACPI Exception (processor_perflib-0255): AE_NOT_FOUND, Evaluating _PSS [20070126]
Jun 24 22:32:24 yetti kernel: powernow-k8: BIOS error - no PSB or ACPI _PSS objects
Jun 24 22:32:24 yetti kernel: ACPI Exception (processor_perflib-0255): AE_NOT_FOUND, Evaluating _PSS [20070126]
Jun 24 22:32:24 yetti kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jun 24 22:32:24 yetti kernel: nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
Jun 24 22:32:24 yetti kernel: r8169: eth1: link up
Jun 24 22:32:24 yetti kernel: NET: Registered protocol family 17
Jun 24 22:32:25 yetti ifup-dhcp: . 
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: leased 192.168.10.142 for 3600 seconds
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: adding IP address 192.168.10.142/21
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: adding default route via 192.168.10.1 metric 0
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: adding route to 169.254.0.0/16 metric 0
Jun 24 22:32:25 yetti modify_resolvconf: Service dhcpcd modified /etc/resolv.conf. See info block in this file
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: setting hostname to `yetti'
Jun 24 22:32:25 yetti dhcpcd[2250]: eth1: exiting
Jun 24 22:32:25 yetti syslog-ng[1678]: SIGHUP received, restarting syslog-ng
Jun 24 22:32:26 yetti ifdown:     eth1      device: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Jun 24 22:32:26 yetti syslog-ng[1678]: new configuration initialized
Jun 24 22:32:26 yetti ifup-dhcp: IP/Netmask: '192.168.10.142'
Jun 24 22:32:26 yetti ifup-dhcp:  / '255.255.248.0'
Jun 24 22:32:26 yetti ifup-dhcp:  ('yetti')
Jun 24 22:32:26 yetti ifup-dhcp:  
Jun 24 22:32:26 yetti ifup:     eth1      device: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Jun 24 22:32:27 yetti SuSEfirewall2: /var/lock/SuSEfirewall2.booting exists which means system boot in progress, exit.
Jun 24 22:32:27 yetti auditd[2851]: Started dispatcher: /sbin/audispd pid: 2853
Jun 24 22:32:27 yetti auditd[2851]: Init complete, auditd 1.6.8 listening for events (startup state disable)
Jun 24 22:32:28 yetti audispd: af_unix plugin initialized
Jun 24 22:32:28 yetti audispd: audispd initialized with q_depth=64 and 1 active plugins
Jun 24 22:32:28 yetti avahi-daemon[2870]: Found user 'avahi' (UID 102) and group 'avahi' (GID 104).
Jun 24 22:32:28 yetti avahi-daemon[2870]: Successfully dropped root privileges.
Jun 24 22:32:28 yetti avahi-daemon[2870]: avahi-daemon 0.6.22 starting up.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Loading service file /etc/avahi/services/sftp-ssh.service.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Loading service file /etc/avahi/services/ssh.service.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Joining mDNS multicast group on interface eth1.IPv4 with address 192.168.10.142.
Jun 24 22:32:28 yetti avahi-daemon[2870]: New relevant interface eth1.IPv4 for mDNS.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Network interface enumeration completed.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Registering new address record for fe80::211:9ff:feda:f016 on eth1.*.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Registering new address record for 192.168.10.142 on eth1.IPv4.
Jun 24 22:32:28 yetti avahi-daemon[2870]: Registering HINFO record with values 'X86_64'/'LINUX'.
Jun 24 22:32:29 yetti avahi-dnsconfd[2886]: Successfully connected to Avahi daemon.
Jun 24 22:32:29 yetti avahi-daemon[2870]: Server startup complete. Host name is yetti.local. Local service cookie is 1200464048.
Jun 24 22:32:30 yetti avahi-daemon[2870]: Service "yetti" (/etc/avahi/services/ssh.service) successfully established.
Jun 24 22:32:30 yetti avahi-daemon[2870]: Service "SFTP File Transfer on yetti" (/etc/avahi/services/sftp-ssh.service) successfully established.
Jun 24 22:32:32 yetti /usr/sbin/cron[2999]: (CRON) STARTUP (V5.0)
Jun 24 22:32:34 yetti powersaved[3028]: WARNING (CpufreqManagement:52) No capability cpufreq_control
Jun 24 22:32:34 yetti powersaved[3028]: WARNING (CpufreqManagement:52) No capability cpufreq_control
Jun 24 22:32:34 yetti smartd[3039]: smartd 5.39 2008-05-08 21:56 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-8 by Bruce Allen, http://smartmontools.sourceforge.net 
Jun 24 22:32:34 yetti smartd[3039]: Opened configuration file /etc/smartd.conf
Jun 24 22:32:34 yetti smartd[3039]: Drive: DEVICESCAN, implied '-a' Directive on line 29 of file /etc/smartd.conf
Jun 24 22:32:34 yetti smartd[3039]: Configuration file /etc/smartd.conf was parsed, found DEVICESCAN, scanning devices
Jun 24 22:32:34 yetti smartd[3039]: Problem creating device name scan list
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sda, opened
Jun 24 22:32:34 yetti smartd[3039]: Device /dev/sda: using '-d sat' for ATA disk behind SAT layer.
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sda, opened
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sda, found in smartd database.
Jun 24 22:32:34 yetti kernel: eth1: no IPv6 routers present
Jun 24 22:32:34 yetti kernel: klogd 1.4.1, ---------- state change ---------- 
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sda, is SMART capable. Adding to "monitor" list.
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sdb, opened
Jun 24 22:32:34 yetti smartd[3039]: Device /dev/sdb: using '-d sat' for ATA disk behind SAT layer.
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sdb, opened
Jun 24 22:32:34 yetti SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEfirewall2 ...
Jun 24 22:32:34 yetti smartd[3039]: Device: /dev/sdb, found in smartd database.
Jun 24 22:32:35 yetti smartd[3039]: Device: /dev/sdb, is SMART capable. Adding to "monitor" list.
Jun 24 22:32:35 yetti smartd[3039]: Monitoring 0 ATA and 2 SCSI devices
Jun 24 22:32:35 yetti SuSEfirewall2: using default zone 'ext' for interface eth0
Jun 24 22:32:35 yetti sshd[3100]: Server listening on :: port 22.
Jun 24 22:32:35 yetti sshd[3100]: Server listening on 0.0.0.0 port 22.
Jun 24 22:32:36 yetti smartd[3121]: smartd has fork()ed into background mode. New PID=3121.
Jun 24 22:32:36 yetti SuSEfirewall2: batch committing...
Jun 24 22:32:37 yetti SuSEfirewall2: Firewall rules successfully set
Jun 24 22:32:37 yetti kernel: bootsplash: status on console 0 changed to on

[menphis]

v tom vypisu z dmesg se ti porad obejvuje hlaska, ze nemuze nastavit skalovani frekvence procesoru, pritom A64 3000+ by tohlem mel podporvat.

Jun 24 22:32:20 yetti rchal: CPU frequency scaling is not supported by your processor.
Jun 24 22:32:20 yetti rchal: boot with 'CPUFREQ=no' in to avoid this warning.
Jun 24 22:32:20 yetti rchal: Cannot load cpufreq governors - No cpufreq driver available
Jun 24 22:32:34 yetti powersaved[3028]: WARNING (CpufreqManagement:52) No capability cpufreq_control
Jun 24 22:32:34 yetti powersaved[3028]: WARNING (CpufreqManagement:52) No capability cpufreq_control

jak to resit a zda to zpusobuje problem nevim, mozna doistalovat nejakej balicek na podporu toho sklaovani nebo si pohrat s ACPI (treba zkusit vypnout). nic dalsiho podezrelyho v tom logu nevidim.

[mates]

Tomuto bych taky doporucil venovat pozornost. Taktez mam A64 3000+ (socket 754 a chipset nvidia) a u mnoha distribuci (urcite Fedora 7,8,9 a i nektery dalsi) jsem se setkal s nahodnymi vytuhy celyho systemu. Bud uz behem startu nebo po par minutach po spusteni. Zajimavy bylo, ze to vetsinou vytuhlo na HALu nebo DBusu, s cimz by imho mohlo souviset i to mountovani.

Resenim bylo vypnuti volby Cool'n'quiet v biosu nebo spusteni systemu s parametry noapic a acpi=off. Samozrejme nefunguje skalovani frekvence procesoru :(

OpenSuse 10.3 jsem zkousel akorat virtualne, takze nevim, jestli by mi to tam se zaplym Cool'n'quiet delalo taky. Ale pokud ne, tak by to asi znamenalo, ze ma 10.3 v kernelu patch, kterej to resi a kterej v jedenactce neni nebo z nejakyho duvodu nefunguje.

Tak to je vsechno, treba to k necemu bude

[Petr Šobáň]

Na mé desce pomohl novější bios.

ASUS M2NPV-VM

Se starým biosem byla deska nestabilní a nefungovalo ACPI.

[Bluebear]

Hmmm. Teprve teď jsem si přečetl celý ten log...

Jun 24 22:32:24 yetti kernel: powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (1 cpu cores) (version 2.20.00)
Jun 24 22:32:24 yetti kernel: ACPI Exception (processor_perflib-0255): AE_NOT_FOUND, Evaluating _PSS [20070126]
Jun 24 22:32:24 yetti kernel: powernow-k8: BIOS error - no PSB or ACPI _PSS objects
Jun 24 22:32:24 yetti kernel: ACPI Exception (processor_perflib-0255): AE_NOT_FOUND, Evaluating _PSS [20070126]

Tohle IMHO není v pořádku. Těžko říct, jestli se to nějak podílí na tom problému, ale u mne jsem dostával velmi podobné hlášení u desky, která měla BIOS updatovaný na podporu Phenomu, ale ještě v ní ten Phenom nebyl nainstalovaný.

[menphis]

Po instalaci, ktera vytvorila systemovou a datovou partition jsem tu druhou jmenovanou odpojil a rucne pripojil cely druhy disk, kde jsem mel data. Muze to byt zdroj problemu?

To snad ne.

A proc by to jako melo vadit odmoutovani/primoutovani disku ???

[soptik]

Mel jsem identicky "zamrzovy" problem po najeti Xek na OpenSUSE 11. Nakonec jsem zjistil ze ho pravdepodobne zpusobuje indexace v Beaglu - beagle a vsechny jeho subkomponenty jsem odinstaloval a vse bezi OK.

[Bluebear]

Nakonec jsem zjistil ze ho pravdepodobne zpusobuje indexace v Beaglu

To je ale strašně divné, protože Beagle je normální userspacová aplikace, ta nemůže (přesněji řečeno nesmí) srazit celou mašinu. Pokud se mu to podaří, jde o bug v kernelu, nebo o hardwarovou chybu.

[Dent]

S OpenSuSE 11 jsem měl naprosto identický problém, jak jsem psal v diskuzi pod zprávičkou. Teď se tam dokonce ozval ještě jeden člověk se tímto problémem. Zajímavé - nemůže to být např. nějakým susím patchem v kernelu?

[Boogie]

Podobna zkusenost, ja ale pro jistotu nechal na disku i SuSE 10.3 a kdyz nabootuji starou tak je vsechno v poradku. Tipuji taky kernel nebo proprietarni ovladac grafiky.

[Mitch]

Presne toto same mi delal Suse 10.2. Vyresil jsem to instalaci OpenSource ovladacu grafiky. Tak bych skusil to a uvidis. Ale me to prijde jako nejpravdepodobnejsi pricina. Disk by asi nezpusobil celkove vytuhnuti systemu.

[Dent]

V mém případě se jedná o intel, takže grafikou to s největší pravděpodobností nebude.

[Elvis]

Tak co zkusit jiny kernel, treba si sam prelozit vlastni

[Dent]

Jeden z důvodů pro používání OpenSuSE (pro mě) je právě nepotřeba sestavení vlastního kernelu. To rovnou můžu dál používat Slacka :))

[xkesh]

Jeden z důvodů pro používání OpenSuSE (pro mě) je právě nepotřeba sestavení vlastního kernelu. To rovnou můžu dál používat Slacka :))

Jo, já něco podobného s OpenSUSE 10.2 vzdal a od té doby, co jsem se zase vrátil ke Gentoo, tak nepozoruju žádná záhadná vytuhnutí.

[Michal Vyskočil]

No v balíčku máš i vanilla verzi jádra, takže kompilovat netřeba.

[Milan]

V intelovskym driveru je chyba ktera zpusobuje zamrznuti pokud je pouzivana hardwerova akcelerace a ta aplikace bezi v okne. Nejcasteji to zatuhne kdyz jina aplikace prekresli okno te puvodni aplikace. Ve full screenu se to neprojevuje.

Pravdou ovsem je ze dojde (vetsinou) pouze k zatuhnuti Xek; ty ovsem nejdou schodit...

[jozka]

OS ovladace grafiky tam byly. Zkusil jsem tedy nvidia a pro jistotu nenajel X server. Ze pry /lib/modules...nvidia.ko neexistuje i kdyz existoval. Asi pockam na nejake dalsi Doinstaloval jsem cpufrequtils. Vcera komp drzel (asi dve hodiny), tak uvidim...

[jozka]

Hm, tak dneska dvakrat zapnu a dvakrat do vytuhne do dvou, tri minut po najeti KDE, ted jsem schvalne v IceWM a zatim to drzi... Ma KDE nekde nejaky log?

[Bluebear]

Za normálních okolností nemá KDE šanci srazit celý stroj. Pokud to opravdu padá jen v KDE a v IceWM ne, tak bych to viděl skoro určitě na bug v Xkách nebo v grafickém driveru, který se projeví při zapnutí kompozitoru nebo nějakých pokročilých vykreslovacích funkcí.

[jozka]

No, vzhledem k tomu, ze nejedou nvidia ovladace, tak pochybuju, ze by se Xka dostaly k nejakym "pokrocilym vykreslovacim funkcim". Ale je pravda, ze Xka jsou ted u mne hlavnim podezrelym.

[Bluebear]

Anebo prehrati graf. karty, to je taky oblibeny zpusob padu...

[jozka]

GeForce 6200 s pasivem. co se na ni muze tesne po startu prehrat? Nevim, proto se pidim... Muzu ji zkusit vytahnout a podivat se na ni... Ale co zatizi grafarnu nejvic, krome her, ktere stejne ale nehraju? Ono to totiz slitne sotva se nacte vsechno po startu KDE.

[Bluebear]

Hmmm... a coz prehrati southbridge nebo neceho jineho na zakl. desce? Pak by to tuhlo pri masivni komunikaci s diskem, mozna i se siti...

[jozka]

Zadna masivni komunikace se nekona. Proste to najede a pak vytuhne. I kdyz... dneska jsem prisel, nastartoval a jedu. Dokonce i Opera, ktera mi brala pul procaku je najednou hodna...

[Bluebear]

Chladnější počasí?

[laco]

kéž by...

[jozka]

Taky jsem si myslel, ale slo to dolu i po te bouri.

[Bluebear]

Ještě na něco jsem si vzpomněl. Měl jsem základní desku, která byla sice navržena jako "AM2+ ready", ale v době, kdy šla na trh, ještě nebyly CPU Phenom. Když jsem do ní později dal Phenom, chovala se divně: v zásadě všechno fungovalo, ale po nějaké době, většinou při větším zatížení, ale někdy taky jenom tak, počítač zkolaboval, obrazovka zčernala a pomohl jen tvrdý reset. Pomohl mi update BIOSu.

[jozka]

No jo, ale tohle je tri roky stary komp, bezely na tom ruzne verze zuzky od 10.0 a knoppix. Mimochodem tenhle post pisu napodruhy, protoze pri prvnim to zatuhlo. Podle gkrellm na prociku 5 procent...

[jozka]

Jenom jsem tohle odeslal, tak znova

[menphis]

nemuze fakt byt problem v hardwaru, zkus memtest, mne trebe minuly rok kdyz byly venku vedra vytuhaval sata radic... ?

[jozka]

Jasne, ale tady to tuhne rano pri 19 stupnich i odpoledne pri 30. Vytuhne to v KDE3, nevytuhne to v IceWM, ani ted v KDE4, ani v Knoppixu... A zacalo to po instalaci 11.0.

[faidron]

Skusal som aj ine distra, ale po vsetkych tych peripetiah sa mi 10.1 zdala najviac. O to viac som prekvapeny ako slape 11.0 To snad nepotrebuje ani RAM, ani CPU. Myslim, ze by sme to rozbehali aj na 486. Kto skusi nech povie. Dobre teda. Mam podobny problem. PC mi mrzne. Niekedy tesne po restarte a niekdy to ide krasne 4 hod a potom blika Caps look a jedine co sa s tym da je buttom. Mam notebook tak ten hardver isiel ok, ale je mozne ze sa daco pokazilo? Osobne by som idel problem niekde okolo acpi alebo skalovania CPU. Myslim, ze X to nebude ani grafika aniz zvuk. Mozno este ram, ale to tiez doteraz no problem a tiez nic nepise.pri najblizsom vytuhnuti tu dam messages.

[trefis]

To by spis chtelo otestovat HW a pak resit suse. Nech jeden den spusteny memtest nebo gold memory a druhy den pak spust orthos(+wine) nebo nejaky jiny nativni CPU test.Pokud vse probehne OK, vis ze to HW neni a resis pouze system.

Mne se zacal taky sekat suse, treba jednou za tyden....nevedel jsem cim to je a pak jsem nahodne rebootnul do windows,ktery padly do par minut. Takze jsem snizil o trosku frekvenci CPU, nechal to 24 projet orthosem a uz je PC stabilni.

[faidron]

07:15:49 to zamrzlo

Jul 18 07:14:40 compaq kernel: ISO 9660 Extensions: Microsoft Joliet Level 3
Jul 18 07:14:40 compaq kernel: ISO 9660 Extensions: RRIP_1991A
Jul 18 07:14:40 compaq hald: mounted /dev/sr0 on behalf of uid 1000
Jul 18 07:14:41 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc
her.d/autofs' exited with error status 1.
Jul 18 07:14:42 compaq SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEf
irewall2 ...
Jul 18 07:14:43 compaq SuSEfirewall2: batch committing...
Jul 18 07:14:43 compaq SuSEfirewall2: Firewall rules successfully set
Jul 18 07:14:43 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc
her.d/nfs' exited with error status 2.
Jul 18 07:14:43 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc
her.d/smbfs' exited with error status 1.
Jul 18 07:15:49 compaq gconfd (ondro-2903): starting (version 2.22.0), pid 2903
user 'ondro'
Jul 18 07:15:49 compaq gconfd (ondro-2903): Resolved address "xml:readonly:/etc/
gconf/gconf.xml.mandatory" to a read-only configuration source at position 0
Jul 18 07:15:49 compaq gconfd (ondro-2903): Resolved address "xml:readwrite:/hom
e/ondro/.gconf" to a writable configuration source at position 1
Jul 18 07:15:49 compaq gconfd (ondro-2903): Resolved address "xml:readonly:/etc/
gconf/gconf.xml.defaults" to a read-only configuration source at position 2
Jul 18 07:15:49 compaq gconfd (ondro-2903): Resolved address "xml:readonly:/etc/
gconf/gconf.xml.vendor" to a read-only configuration source at position 3
Jul 18 07:15:49 compaq gconfd (ondro-2903): Resolved address "xml:readonly:/etc/
gconf/gconf.xml.schemas" to a read-only configuration source at position 4


Jul 18 07:18:52 compaq syslog-ng[1556]: syslog-ng version 1.6.12 starting
Jul 18 07:18:53 compaq rchal: CPU frequency scaling is not supported by your pro
cessor.
Jul 18 07:18:53 compaq rchal: boot with 'CPUFREQ=no' in to avoid this warning.
Jul 18 07:18:53 compaq rchal: Cannot load cpufreq governors - No cpufreq driver
available
Jul 18 07:18:56 compaq SuSEfirewall2: batch committing...
Jul 18 07:18:56 compaq SuSEfirewall2: Firewall rules set to CLOSE.
Jul 18 07:18:57 compaq kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.007:2): operation="pro
file_load" name="/bin/ping" name2="default" pid=1272
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.087:3): operation="pro
file_load" name="/sbin/klogd" name2="default" pid=1302
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.215:4): operation="pro
file_load" name="/sbin/syslog-ng" name2="default" pid=1305
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.287:5): operation="pro
file_load" name="/sbin/syslogd" name2="default" pid=1310
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.359:6): operation="pro
file_load" name="/usr/sbin/avahi-daemon" name2="default" pid=1311
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.431:7): operation="pro
file_load" name="/usr/sbin/identd" name2="default" pid=1312
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.507:8): operation="pro
file_load" name="/usr/sbin/mdnsd" name2="default" pid=1313
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.643:9): operation="pro
file_load" name="/usr/sbin/named" name2="default" pid=1318
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.811:10): operation="pr
ofile_load" name="/usr/sbin/nscd" name2="default" pid=1335
Jul 18 07:18:57 compaq kernel: type=1505 audit(1216358329.983:11): operation="pr
ofile_load" name="/usr/sbin/ntpd" name2="default" pid=1347
Jul 18 07:18:57 compaq kernel: powernow: This module only works with AMD K7 CPUs
Jul 18 07:18:57 compaq kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jul 18 07:18:57 compaq kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jul 18 07:18:57 compaq kernel: nf_conntrack version 0.5.0 (15360 buckets, 61440
max)
Jul 18 07:18:58 compaq kernel: IA-32 Microcode Update Driver: v1.14a 
Jul 18 07:18:58 compaq firmware.sh[2041]: Cannot find  firmware file 'intel-ucod
e/0f-02-07'
Jul 18 07:18:59 compaq network: Starting the NetworkManager
Jul 18 07:19:00 compaq nm-system-settings: Loaded plugin ifcfg-suse: (C) 2008 No
vell, Inc.  To report bugs please use the NetworkManager mailing list.
Jul 18 07:19:00 compaq nm-system-settings: Loaded plugin keyfile: (c) 2007 - 200
8 Red Hat, Inc.  To report bugs please use the NetworkManager mailing list.
Jul 18 07:19:03 compaq kernel: [drm] Initialized drm 1.1.0 20060810
Jul 18 07:19:03 compaq kernel: ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10
Jul 18 07:19:03 compaq kernel: ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0
] -> GSI 10 (level, low) -> IRQ 10
Jul 18 07:19:03 compaq kernel: [drm] Initialized radeon 1.28.0 20060524 on minor
 0
Jul 18 07:19:03 compaq auditd[2219]: Started dispatcher: /sbin/audispd pid: 2222
Jul 18 07:19:03 compaq audispd: af_unix plugin initialized
Jul 18 07:19:03 compaq audispd: audispd initialized with q_depth=64 and 1 active
 plugins
Jul 18 07:19:03 compaq auditd[2219]: Init complete, auditd 1.6.8 listening for e
vents (startup state disable)
Jul 18 07:19:03 compaq kernel: eth0: DSPCFG accepted after 0 usec.
Jul 18 07:19:03 compaq kernel: eth0: link up.
Jul 18 07:19:03 compaq kernel: eth0: Setting full-duplex based on negotiated lin
k capability.
Jul 18 07:19:04 compaq dhclient: Internet Systems Consortium DHCP Client V3.0.6
Jul 18 07:19:04 compaq dhclient: Copyright 2004-2007 Internet Systems Consortium
.
Jul 18 07:19:04 compaq dhclient: All rights reserved.
Jul 18 07:19:04 compaq dhclient: For info, please visit http://www.isc.org/sw/dh
cp/
Jul 18 07:19:04 compaq dhclient:
Jul 18 07:19:04 compaq avahi-daemon[2235]: Found user 'avahi' (UID 102) and grou
p 'avahi' (GID 104).
Jul 18 07:19:04 compaq avahi-daemon[2235]: Successfully dropped root privileges.
Jul 18 07:19:04 compaq avahi-daemon[2235]: avahi-daemon 0.6.22 starting up.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Loading service file /etc/avahi/servi
ces/sftp-ssh.service.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Loading service file /etc/avahi/servi
ces/ssh.service.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Network interface enumeration complet
ed.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Registering HINFO record with values
'I686'/'LINUX'.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Server startup complete. Host name is
 compaq.local. Local service cookie is 1547963672.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Service "compaq" (/etc/avahi/services
/ssh.service) successfully established.
Jul 18 07:19:04 compaq avahi-daemon[2235]: Service "SFTP File Transfer on compaq
" (/etc/avahi/services/sftp-ssh.service) successfully established.
Jul 18 07:19:04 compaq kernel: NET: Registered protocol family 17
Jul 18 07:19:04 compaq dhclient: Listening on LPF/eth0/00:0b:cd:a7:f7:b6
Jul 18 07:19:04 compaq dhclient: Sending on   LPF/eth0/00:0b:cd:a7:f7:b6
Jul 18 07:19:04 compaq dhclient: Sending on   Socket/fallback
Jul 18 07:19:04 compaq kernel: agpgart: Found an AGP 2.0 compliant device at 000
0:00:00.0.
Jul 18 07:19:04 compaq kernel: agpgart: Putting AGP V2 device at 0000:00:00.0 in
to 4x mode
Jul 18 07:19:04 compaq kernel: agpgart: Putting AGP V2 device at 0000:01:05.0 in
to 4x mode
Jul 18 07:19:05 compaq kernel: [drm] Setting GART location based on old memory m
ap
Jul 18 07:19:05 compaq kernel: [drm] writeback test succeeded in 1 usecs
Jul 18 07:19:06 compaq powersaved[2284]: WARNING (CpufreqManagement:52) No capab
ility cpufreq_control
Jul 18 07:19:06 compaq powersaved[2284]: WARNING (CpufreqManagement:52) No capab
ility cpufreq_control
Jul 18 07:19:06 compaq sshd[2331]: Server listening on 0.0.0.0 port 22.
Jul 18 07:19:06 compaq SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEf
irewall2 ...
Jul 18 07:19:07 compaq SuSEfirewall2: batch committing...
Jul 18 07:19:07 compaq SuSEfirewall2: Firewall rules successfully set
Jul 18 07:19:08 compaq dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67
 interval 2
Jul 18 07:19:10 compaq dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67
 interval 4
Jul 18 07:19:10 compaq dhclient: DHCPOFFER from 158.197.196.1
Jul 18 07:19:13 compaq dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67
Jul 18 07:19:13 compaq dhclient: DHCPACK from 158.197.196.1
Jul 18 07:19:13 compaq avahi-daemon[2235]: Joining mDNS multicast group on inter
face eth0.IPv4 with address 158.197.196.127.
Jul 18 07:19:13 compaq avahi-daemon[2235]: New relevant interface eth0.IPv4 for
mDNS.
Jul 18 07:19:13 compaq avahi-daemon[2235]: Registering new address record for 15                              8.197.196.127 on eth0.IPv4.
Jul 18 07:19:13 compaq dhclient: bound to 158.197.196.127 -- renewal in 1575 sec                              onds.
Jul 18 07:19:13 compaq kernel: printk: 3 messages suppressed.
Jul 18 07:19:13 compaq kernel: martian source 158.197.196.127 from 193.41.230.73                              , on dev eth0
Jul 18 07:19:13 compaq kernel: ll header: 00:0b:cd:a7:f7:b6:00:17:a4:a4:e8:f9:08                              :00
Jul 18 07:19:15 compaq kernel: ISO 9660 Extensions: Microsoft Joliet Level 3
Jul 18 07:19:15 compaq kernel: ISO 9660 Extensions: RRIP_1991A
Jul 18 07:19:15 compaq hald: mounted /dev/sr0 on behalf of uid 1000
Jul 18 07:19:16 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc                              her.d/autofs' exited with error status 1.
Jul 18 07:19:17 compaq SuSEfirewall2: Setting up rules from /etc/sysconfig/SuSEf                              irewall2 ...
Jul 18 07:19:17 compaq SuSEfirewall2: batch committing...
Jul 18 07:19:17 compaq SuSEfirewall2: Firewall rules successfully set
Jul 18 07:19:18 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc                              her.d/nfs' exited with error status 2.
Jul 18 07:19:18 compaq nm-dispatcher.action: Script '/etc/NetworkManager/dispatc                              her.d/smbfs' exited with error status 1.
Jul 18 07:20:24 compaq su: (to root) ondro on /dev/pts/1
compaq:~ #

Nevylucujem ze by sa mohlo jednat o hw chybu, Co znamenaju tie hlasky ohladne CPU ktore vypisuje hned na zaciatku bootu, cpu je skalovatelne.

compaq:~ # cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 15
model           : 2
model name      : Mobile Intel(R) Celeron(R) CPU 2.00GHz
stepping        : 7
cpu MHz         : 1993.632
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe up pebs bts cid
bogomips        : 3991.93
clflush size    : 64

Co myslite? este moj web: www.sykora.sk

[linuxik]

Ahoj,

prvni co by to chtelo zjistit je, jestli zatuhne cely system nebo jen X-ka. Idealne jestli mas moznost zkusit se pripojit na stroj pres ssh z jineho PC. Taky by jsi se mohl podivat do logu X-windows ve /var/log/Xorg.0.log (po restartu Xorg.0.log.old) nebo v HOME adresari do .xsession-errors. Takhle jsou to jen dohady. A nakonec muzes zkusit pouzit misto nv nebo nvidia ovladac vesa, bude to sice pomaly, ale na zkousku to staci.

[faidron]

SuSE 11.0 Niekolko chyb, je tento system este dotiahnut, ale postupne patche by to mohli zmiernit. Co je najvacsim problemom je zamrzanie, ja mam viac ako 5 rokov stary notebook, a to mrzlo takmer vzdy ci uz pri starte KDE, alebo pocas behu. Hlavne prvy studeny start 100 % zamrznutie do 10 min. Takze je mozne ze sa mi to podarilo vyriesit, mozno ciastocne: Najprve som pozrel messages. Tk pisal z nevie najst vhodny modul tak som o dodal:

compaq:~ # cpufreq-info
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006
Report errors and bugs to http://bugs.opensuse.org, please.
analyzing CPU 0:
  driver: p4-clockmod
  CPUs which need to switch frequency at the same time: 0
  hardware limits: 250 MHz - 2.00 GHz
  available frequency steps: 250 MHz, 500 MHz, 750 MHz, 1000 MHz, 1.25 GHz, 1.50 GHz, 1.75 GHz, 2.00 GHz
  available cpufreq governors: conservative, userspace, powersave, ondemand, performance
  current policy: frequency should be within 250 MHz and 2.00 GHz.
                  The governor "ondemand" may decide which speed to use
                  within this range.
  current CPU frequency is 2.00 GHz (asserted by call to hardware).

ovl Potom som memstat86 otestoval pamate baliek v instalacii, potrebne rebootovat. Neskor skusil Vanilla kernel je v tiez distribucii. Chyba sa stale opakovala.

Odinstaloval som komplet beagle. Neviem na co konkretne to indexovanie sluzi, ale okrem peknej ikony som z toho nemal ziaden skor opacny ucinok. Je mozne ze neskor to este niekde zmrzne, ale uvidim casom.

Vela stastia.