Dotaz: Debian - z CRT na LCD

[teekey]

mam problem s nastavenim monitoru v Debianu. Mam rozchozenou 3D podporu, vsechno vyladene, jenomze muj LCD monitor nevzlada podle systemu nizsi rozliseni jak 1024x768 (coz je blbost). Pred par mesici jsem stejny problem resil u Mandrivy (nahrada CRT novym LCD/TFT), nicmene v MDV slo novy HW tzv. "naklikat", kde jsem z Generic-CRT 1024x768@60Hz zvolil Generic-TFT 1024x768@60Hz nebo tak nejak. Snazim se neceho podobneho dopidit i v Debianu, ale zatim marne. V Xorg.conf nicmoc neni - vygenerovany default nvidia + nastaveni klavesnice...za kazdou radu budu vdecny, dekuji

Odpovědi

[oroborus]

Ak som to spravne pochopil, chces aby sa pri rozlisenie 1024x768 pouzivala obnovovacia frekvencia 60Hz. V /etc/X11/xorg treba dat do sekcie "Screen" podsekcie "Display" do casti Modes dalsi udaj o rozliseni a obnovovacej frekvencii

priklad :

Section "Screen"
   Identifier  "Default Screen"
   Device      "nVidia Corporation NV43 [GeForce 6600]"
   Monitor     "Obecný monitor"
   DefaultDepth   24
.....  atd ....
    SubSection "Display"
      Depth    24
      Modes    "1024x768_60" "ostatne rozlisenia" 
   EndSubSection

EndSection

Slovenska wiki o Debiane :

debian.nfo.sk/Wiki/NastavenieXorg

[teekey]

muj problem je, ze kdyz nastavim rozliseni na 800x600 tak monitor zcerna a vypise NO VALID INPUT - mel sem ten problem jiz drive, ale v Mandrive sem to vyresil pres klikatka a nevim tedy jak na to v Xorg.conf Problem nastava tedy i v pripade spousteni aplikaci, ktere vyzaduji nizsi rozliseni (hry apod.). Dekuji za radu, ale problem mi nevyresila

[Smajchl]

tak to samý ale napiš to tam pro 800x600, konkrétně tenhle způsob neznám, znám to že do sekce monitor napíšeš vetical a horizontal sync aneb rozsah frekvencí co ten monitor zvládá a pak neni problém.

[Max]

Pošli sem tvůj xorg.conf a typ tvého LCD monitoru.
Zdar Max

[teekey]

zda se, ze jsem problem jiz castecne vyresil. Nicmene, v default konfiguraci xorg.conf (bez nvidia akcelerace) vse funguje (ale v confu taky skoro nic neni), po prepsani xorg.conf nvidia drivery (binary driver od nvidia pri instalaci ma volbu k prepsani xorg.conf) jde pouzit pouze rozliseni 1024x768 a 1280x1024 - ve vyberu jsou i nizsi, ale monitor vzdy zahlasi No Valid Input - nebo neco takoveho :-/ Ted sem si pohral s nvidia-settings a upravil xorg.conf a vypada to nejak takhle:

 

<pre># nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings:  version 1.0  (buildmeister@builder57)  Thu Jul 17 18:40:12 PDT 2008

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder57)  Thu Jul 17 18:39:19 PDT 2008

Section "ServerLayout"
    Identifier     "Layout0"
    Screen      0  "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
EndSection

Section "Files"
    RgbPath         "/usr/X11R6/lib/X11/rgb"
EndSection

Section "Module"
    Load           "dbe"
    Load           "extmod"
    Load           "type1"
    Load           "freetype"
    Load           "glx"
EndSection

Section "ServerFlags"
    Option         "Xinerama" "0"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
    Option         "XkbModel" "pc105"
    Option         "XkbLayout" "cz,us"
    Option         "XkbOptions" "grp:alt_shift_toggle,grp_led:scroll"
EndSection

Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "Acer V173"
    HorizSync       31.0 - 80.0
    VertRefresh     56.0 - 75.0
    Option         "DPMS"
EndSection

Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
EndSection

Section "Device"
    Identifier     "Videocard0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce FX 5200"
EndSection

Section "Screen"
    Identifier     "Screen0"
    Device         "Videocard0"
    Monitor        "Monitor0"
    DefaultDepth    16
    Option         "TwinView" "0"
    Option         "TwinViewXineramaInfoOrder" "CRT-0"
    Option         "metamodes" "1280x1024_60 +0+0; 1024x768_60 +0+0; 800x600_75 +0+0; 800x600d60 +0+0"
    SubSection     "Display"
        Depth       16
    EndSubSection
EndSection
</pre>

 

jeste to ma nejake mouchy, ale to vyresim pozdeji, hlavni je, ze uz de nastavovat rozliseni a funguji i "aplikace", ktere driv vypinaly monitor

[Max]

Takhle by ti to mělo fachčit (změň a restartni xserver), teda za předpokladu, že máš tuhle mršku Acer V173:

# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings:  version 1.0  (buildmeister@builder57)  Thu Jul 17 18:40:12 PDT 2008

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder57)  Thu Jul 17 18:39:19 PDT 2008

Section "ServerLayout"
    Identifier     "Layout0"
    Screen      0  "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
EndSection

Section "Files"
    RgbPath         "/usr/X11R6/lib/X11/rgb"
EndSection

Section "Module"
    Load           "dbe"
    Load           "extmod"
    Load           "type1"
    Load           "freetype"
    Load           "glx"
EndSection

Section "ServerFlags"
    Option         "Xinerama" "0"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
    Option         "XkbModel" "pc105"
    Option         "XkbLayout" "cz,us"
    Option         "XkbOptions" "grp:alt_shift_toggle,grp_led:scroll"
EndSection


Section "Monitor"
    Identifier     "Acer V173"
    HorizSync       30 - 80
    VertRefresh     55 - 75
    Option         "DPMS"
EndSection


Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    #Option "ConnectedMonitor" "CRT,DFP"
    #Option "RenderAccel" "true"
    #Option "AddARGBGLXVisuals" "true"
    #Option "TripleBuffer" "True"
    #Option "DisableGLXRootClipping" "true"
    #Option "XAANoOffscreenPixmaps" "true
EndSection


#Section "Extensions"
#  Option "Composite" "Enable"
#EndSection


Section "Device"
    Identifier     "Videocard0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce FX 5200"
EndSection


Section "Screen"
    Identifier  "Screen0"
    Device      "Videocard0"
    Monitor     "Acer V173"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1280x1024" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

Přidal jsem ti tam i pár zakomentovaných řádků k zamyšlení. Takže stačí jen odkomentovat a testovat :)
Zdar Max

[Max]

Eh, ty tam máš tu grafiku definovanou 2x a já přidal ty zakomentované věci k té nepoužívané verzi, takže tohle se může smazat :

Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    #Option "ConnectedMonitor" "CRT,DFP"
    #Option "RenderAccel" "true"
    #Option "AddARGBGLXVisuals" "true"
    #Option "TripleBuffer" "True"
    #Option "DisableGLXRootClipping" "true"
    #Option "XAANoOffscreenPixmaps" "true
EndSection

A ty komentáře si dopiš k této verzi :

Section "Device"
    Identifier     "Videocard0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce FX 5200"
 
    #Option "ConnectedMonitor" "CRT,DFP"
    #Option "RenderAccel" "true"
    #Option "AddARGBGLXVisuals" "true"
    #Option "TripleBuffer" "True"
    #Option "DisableGLXRootClipping" "true"
    #Option "XAANoOffscreenPixmaps" "true
EndSection

Zdar Max

[teekey]

diky, mrknu na to

[Dundee5]

Doporučuju zkusit jednoduché:

dpkg-reconfigure xserver-xorg

Řešil jsem tím přechod na jiný monitor s hlášením "Out of range".