Dotaz: GPRS a wvdial

[vladaf]

Zdravim, chtel bych se pomoci sve Nokia 3110c pripojit na net. Ve win to jde pomoci Nokiackeho softu dobre. V Opensuse 11.2 to zkousim pomoci wvdial. Telefon se nekam pripoji, ale ja se nikam nedostanu. Dostavam toto

spiranthes:~ # wvdial DATA      
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.                    
--> Sending: ATZ                           
ATZ                                        
OK                                         
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0             
OK                                            
--> Sending: AT+CGDCONT=1,"IP","internet"     
AT+CGDCONT=1,"IP","internet"                  
OK                                            
--> Modem initialized.                        
--> Idle Seconds = 3600, disabling automatic reconnect.
--> Sending: ATDT*99***1#                              
--> Waiting for carrier.
ATDT*99***1#
CONNECT
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> Carrier detected.  Starting PPP immediately.
--> Starting pppd at Wed Oct  6 09:25:28 2010
--> Pid of pppd: 10756
--> Using interface ppp0
--> local  IP address 85.161.138.176
--> remote IP address 10.6.6.6
--> primary   DNS address 160.218.10.200
--> secondary DNS address 160.218.43.200
--> Script /etc/ppp/ip-up run successful
--> Default route Ok.
--> warning, can't find address for `www.suse.de`
--> warning, address lookup does not work
--> Nameserver (DNS) failure, the connection may not work.
--> Connected... Press Ctrl-C to disconnect

muj /etc/wvdial.conf

[Modem0]                           
Modem = /dev/rfcomm0               
Baud = 230400                      
SetVolume = 0                      
DialCommand = ATDT                 
FlowControl = Hardware(CRTSCTS)    

[Modem1]
Modem = /dev/ttyACM0
Baud = 230400       
SetVolume = 0       
DialCommand = ATDT  
FlowControl = Hardware(CRTSCTS)

[Dialer GPRS]
Username = 1 
Password = 1 
Phone = *99***1#
Mode = 1        
Inherits = Modem0

[Dialer DATA]
Username = <>
Password = <>
Phone = *99***1#
Mode = 1        
Inherits = Modem1

[Dialer Defaults]
Modem = /dev/rfcomm0
Baud = 230400
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,"IP","internet"
ISDN = 0
Modem Type = Analog Modem
Area Code =
Phone = *99***1#
Username = <>
Password = <>
Ask Password = 0
Dial Command = ATDT
Stupid Mode = 1
Compuserve = 0
Force Address =
Idle Seconds = 3600
DialMessage1 =
DialMessage2 =
ISDN = 0
Auto DNS = 1

ifconfig

ppp0      Link encap:Point-to-Point Protocol
          inet addr:85.161.138.176  P-t-P:10.6.6.6  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:64 (64.0 b)  TX bytes:585 (585.0 b)

dmesg

[  798.696884] PPP generic driver version 2.4.2
[  801.501689] PPP BSD Compression module registered
[  801.539570] PPP Deflate Compression module registered
[  880.704062] CE: hpet increasing min_delta_ns to 15000 nsec

spiranthes:~ # route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
10.6.6.6        0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         0.0.0.0         0.0.0.0         U     0      0        0 ppp0

Za kazdou radu budu vdecny.

Odpovědi

[NN]

--> warning, can't find address for `www.suse.de`
--> warning, address lookup does not work
--> Nameserver (DNS) failure, the connection may not work

Problem s resolvovanim ?

NN

[vladaf]

Ano, ale nevim, jak to napravit. Docasne pomohlo to rucne narvat do resolv.conf, ale systemove reseni to neni.

[lertimir]

spíše než problém s DNS je to problém s nastavením IP adres. U ifconfig je na ppp0 adaptéru nějaká adresa, která není v route. Může to být, že špatně chodí dhcp klient. v suse dhcpcd. běží ted daemon mezi procesy? Podle toho co je v ifconfig tak ppp protokol--spojová vrstva -- běží. funguje ping na IP adresy? má systém ve windows přibližně stejnou IP? 85.161.138.176? Jaké jsou v windows DNS servery? jakoé jsou v linuxu? ty by to měl také dostat s DHCP. adresa 10.6.6.6 patří tuším jen tomu linkovému spojení.