Dotaz: USB2.0 modul

[ubka7617]

Dobry den, mam jednu USB tlaciaren s USB2.

Operacny system je Debian 6

Mam k nemu aj ovladac. po pripojeni zariadenia mi v syslogu vyhadzuje stale dookola, je jedno ci je spusteni modul ovladace alebo nie.

Jul 20 15:17:39 test kernel: [ 1729.637037] usb 2-2: reset high speed USB device using ehci_hcd and address 2 Jul 20 15:17:39 test kernel: [ 1729.772832] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0DD4 pid 0x0201 Jul 20 15:17:39 test kernel: [ 1729.773296] usblp1: removed Jul 20 15:17:39 test kernel: [ 1729.889037] usb 2-2: reset high speed USB device using ehci_hcd and address 2 Jul 20 15:17:39 test kernel: [ 1730.024927] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0DD4 pid 0x0201 Jul 20 15:17:39 test kernel: [ 1730.025604] usblp1: removed

po zruseni modulu ehci_hcd:

Jul 20 15:18:57 test kernel: [ 1808.208422] usb 5-2: reset full speed USB device using uhci_hcd and address 2 Jul 20 15:18:57 test kernel: [ 1808.359685] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0DD4 pid 0x0201 Jul 20 15:18:57 test kernel: [ 1808.359726] sd 5:0:0:0: [sdb] Unhandled error code Jul 20 15:18:57 test kernel: [ 1808.359733] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK Jul 20 15:18:57 test kernel: [ 1808.359743] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 Jul 20 15:18:57 test kernel: [ 1808.359767] end_request: I/O error, dev sdb, sector 0 Jul 20 15:18:57 test kernel: [ 1808.359778] Buffer I/O error on device sdb, logical block 0 Jul 20 15:18:57 test kernel: [ 1808.359789] Buffer I/O error on device sdb, logical block 1

Jul 20 15:19:00 test kernel: [ 1811.356409] usblp1: removedJul 20 15:19:04 test kernel: [ 1815.269026] usb 5-2: reset full speed USB device using uhci_hcd and address 2 Jul 20 15:19:05 test kernel: [ 1815.424617] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0DD4 pid 0x0201 Jul 20 15:19:08 test kernel: [ 1818.416363] usblp1: removed Jul 20 15:19:08 test kernel: [ 1818.528026] usb 5-2: reset full speed USB device using uhci_hcd and address 2 Jul 20 15:19:08 test kernel: [ 1818.680234] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0DD4 pid 0x0201 Jul 20 15:19:08 test kernel: [ 1818.683299] usblp1: removed

Vopred dakujem za kazdu radu

Odpovědi

[Pavel Stárek]

Co to je za tiskárnu? Soudě dle výrobce nějaký label/POS printer? Na svých stránkách mají jakési ovladače pro CUPS, ale když se neví ten typ, tak se těžko něco hledá. Možná bude potřeba novější kernel.

[Mti.]

Nemuze byt vadny kabl nebo nejaka takova smutna zalezitost? Jede ta tiskarna jinde? (co je to za tiskarnu?)

(ps: zkus to priste se znackou <pre> ....vypis logu... </pre>, bude se to lip cist)

[ubka7617]

Je to pos printer. nasiel som na intaku:

usb interface is set in "enabled" and not in "mass storage".

You can check and modify it from the setup

[ubka7617]

problem je v tom ze to chce natiahnut ako usb disk a nie ako printer a preto sa biju hci na usb

[ubka7617]

da sa neako vypnut mass storage pre konkretne zariadnei ked viem idVendor a idProduct ? dakujem

[ubka7617]

tak som na to prisiel zrusil som kontrolu masstorage v hal pre dany idVendor a idProduct