Dotaz: wifi na asus A6M (ovladac bcm4318)

[opicze]

Zdravím. Vím, už to tu bylo xkrát, ale já se fakt snažím. Čtu česká i zahraniční fora, ale stale nic.

Snažím se rozchodit wifi na svém notebooku. ASUS A6M (A6000 series) Distro SUSE 10.2 (32bit)

Uz jsem toho zkusil moc, nekolikrát jsem instaloval a odinstalovaval ndiswrapper, zkousel ruzne ovladace. Zkousel extrahovat firmware, atd... ale nic, nedokazu ani posoudit jestli sem si system nejak nezas... pro vsechny ty experimenty.

Víc možná řekne několik výpisů s terminálu:

bananas:~ #

bananas:~ # iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

sit0      no wireless extensions.

bananas:~ # ndiswrapper -v
utils version: 1.9
driver version:        1.39
vermagic:       2.6.18.2-34-default SMP mod_unload 586 REGPARM gcc-4.1

bananas:~ # ndiswrapper -l
bcmwl5 : driver installed
bananas:~ #

bananas:~ # dmesg | grep ndiswrapper
bananas:~ #

bananas:/windows/E/download/linux/wifi4/bcmwl5 # dmesg
Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001bfc0000 (usable)
 BIOS-e820: 000000001bfc0000 - 000000001bfce000 (ACPI data)
 BIOS-e820: 000000001bfce000 - 000000001bff0000 (ACPI NVS)
 BIOS-e820: 000000001bff0000 - 000000001c000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 114624
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 110528 pages, LIFO batch:31
DMI present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 ACPIAM                                ) @ 0x000fbb90
ACPI: RSDT (v001 A M I  OEMRSDT  0x06000630 MSFT 0x00000097) @ 0x1bfc0000
ACPI: FADT (v002 A M I  OEMFACP  0x06000630 MSFT 0x00000097) @ 0x1bfc0200
ACPI: MADT (v001 A M I  OEMAPIC  0x06000630 MSFT 0x00000097) @ 0x1bfc0390
ACPI: MCFG (v001 A M I  OEMMCFG  0x06000630 MSFT 0x00000097) @ 0x1bfc0400
ACPI: OEMB (v001 A M I  AMI_OEM  0x06000630 MSFT 0x00000097) @ 0x1bfce040
ACPI: DSDT (v001  A0502 A0502000 0x00000000 INTL 0x02002026) @ 0x00000000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1c000000:e2c00000)
Detected 1607.363 MHz processor.
Built 1 zonelists.  Total pages: 114624
Kernel command line: root=/dev/hdc6 vga=0x317    resume=/dev/hdc8 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447400k/458496k available (1697k kernel code, 10464k reserved, 968k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3218.10 BogoMIPS (lpj=6436218)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
CPU: After vendor identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3150k freed
ACPI: Core revision 20060707
ACPI Error (psloop-0196): Found unknown opcode FD at AML address dc80d7a5 offset 5341, ignoring [20060707]
ACPI Error (psloop-0196): Found unknown opcode FD at AML address dc80d7a5 offset 5341, ignoring [20060707]
CPU0: AMD Mobile AMD Sempron(tm) Processor 3200+ stepping 02
Total of 1 processors activated (3218.10 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ... works.
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:05.0
PCI: Transparent bridge - 0000:00:10.0
PCI: Bus #05 (-#08) is hidden behind transparent bridge #04 (-#05) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
ACPI: Embedded Controller [EC0] (gpe 32) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *5
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *5
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:02.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: d000-dfff
  MEM window: df600000-df6fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:04:01.0
  IO window: 0000e000-0000e0ff
  IO window: 0000e400-0000e4ff
  PREFETCH window: 20000000-21ffffff
  MEM window: 22000000-23ffffff
PCI: Bridge: 0000:00:10.0
  IO window: e000-efff
  MEM window: df700000-dfffffff
  PREFETCH window: db000000-dcffffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
ACPI: PCI Interrupt 0000:04:01.0[A] -> Link [LNKB] -> GSI 19 (level, low) -> IRQ 177
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1176569786.840:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:03.0 to 64
pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
vesafb: framebuffer at 0xc0000000, mapped to 0xdc880000, using 6144k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d700
vesafb: pmi: set display start = c00cd736, set palette = c00cd7a0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 bytes,<6>...found (1024x768, 46202 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI: Thermal Zone [TZ00] (41 C)
NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP51: chipset revision 161
NFORCE-MCP51: not 100% native mode: will probe irqs later
NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input2
hda: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HTS541080G9AT00, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 512KiB
hdc: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hdc: cache flushes supported
 hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 hdc7 hdc8 hdc9 >
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 217, io mem 0xdf5de000
Linux agpgart interface v0.101 (c) Dave Jones
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x600
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x700
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 225, io mem 0xdf5dfc00
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 21 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:10.1 to 64
hda_codec: Unknown model for ALC861, trying auto-probe from BIOS...
ALSA sound/pci/hda/hda_codec.c:2117: autoconfig: line_outs=1 (0xb/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:2121:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:2123:    hp=0xe, dig_out=0x12, din_in=0x0
ALSA sound/pci/hda/hda_codec.c:2131:    inputs: mic=0xd, fmic=0x0, line=0xc, fline=0x0, cd=0x11, aux=0x0
nvidia: module license 'NVIDIA' taints kernel.
ieee1394: Initialized config rom entry `ip1394'
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNEA] -> GSI 18 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xdd042000, 00:18:f3:29:1c:bb, IRQ 50
ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 17
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNEC] -> GSI 17 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:05.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  1.0-9755  Mon Feb 26 23:21:15 PST 2007
sdhci: SDHCI controller found at 0000:04:01.2 [1180:0822] (rev 17)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 16
ACPI: PCI Interrupt 0000:04:01.2[C] -> Link [LNKD] -> GSI 16 (level, low) -> IRQ 66
mmc0: SDHCI at 0xdf7ff800 irq 66 DMA
Yenta: CardBus bridge found at 0000:04:01.0 [1043:1367]
Yenta: ISA IRQ mask 0x04b8, PCI irq 177
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#04) from #05 to #08
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
cs: IO port probe 0xe000-0xefff: clean.
pcmcia: parent PCI bridge Memory window: 0xdf700000 - 0xdfffffff
pcmcia: parent PCI bridge Memory window: 0xdb000000 - 0xdcffffff
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
ACPI: PCI Interrupt 0000:04:01.1[B] -> Link [LNKC] -> GSI 19 (level, low) -> IRQ 177
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[177]  MMIO=[df7ff000-df7ff7ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: excluding 0x828-0x82f 0x840-0x85f 0x870-0x877 0x880-0x887 0x8c0-0x8ff
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 722884k swap on /dev/hdc8.  Priority:-1 extents:1 across:722884k
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800036225a6]
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
loop: loaded (max 8 devices)
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1176569805.209:2): AppArmor initialized

ACPI: AC Adapter [AC0] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3200+ processors (version 2.00.00)
powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x11
powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x18
powernow-k8: ph2 null fid transition 0x8
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
audit(1176562639.769:3): audit_pid=3390 old=0 by auid=4294967295
bootsplash: status on console 0 changed to on
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
ip_tables: (C) 2000-2006 Netfilter Core Team
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready


bananas:~ # lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:05.0 VGA compatible controller: nVidia Corporation C51 PCI Express Bridge (rev a2)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
04:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
04:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08)
04:01.2 Generic system peripheral [Class 0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
04:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08)
04:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)

a par poznamek k tomu (vycházím z problému různých návodů)

- jadro mám 2.6.18.2-34 i686

- do souboru "etc/modprobe.d/blacklist" jsem přidal řádek: "blacklist bcm43xx"

- soubor "etc/modules" neexistuje, takže jsem nedopsal řádek "ndiswrapper"

- soubor "etc/sysconfig/hardware/hwcfg-bus-pci-0000:04:03.0", neexistuje takže jsem ani výraz "bcm43xx" nenahradil výrazem "ndiswrapper"

- zkousel jsem i nainstalovat balicek s bcm43-fwcutte pro linux, instalace probehla ok, ale nezjistil jsem jak ho spustit

acpi mi funguje skvele, ovladacu mam nezpocet, kazdy z jineho zdroje, btw jak poznam jestli jsou pro 64bib nebo 32bit?

Takže tak...vím že je to vyčerpavajicim, kdyby se však našla nějaká dobrád duše schoná mi poradit, byl bych moc vděčný.

Martin.

Odpovědi

[Jiri Uncovsky]

Ahoj,

mám taktéž notebook série A6M (konkrétně A6M-Q057). Podle výpisu lspci to vypadá na tutéž kartu. Mám ovšem 64bitový Debian a používám modul bcm43xx a karta funguje.

Pro rozchození jsem pomocí bcm43-fwcutter stáhl a nainstaloval firmware. Nešifrovaný režim je ok, ale šifrovaný režim (WEP) je občas magie. Pokud chci síť nahodit, tak:

ifconfig eth1 down

iwconfig eth1 essid XXXX key restricted XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX channel X

a pokud chytím signál tak (někdy tyto první dva kroky opakuji):

ifconfig eth1 up

dhclient eth1

Kartu jsem nebyl schopen donutit používat více než 11Mbit/s. Síla signálu je divná, ale dnes jsem zkoušel debianní jádro 2.6.20 a aspoň v tomto se to zlepšilo (už to neměří 100%).

[opicze]

ten já jsem si zkoušel nainstalovat, ale v nabidce kde nikde neni a v terminalu prikazy "bcm43-fwcutter", "fwcutter" taky nejdou a kdyz ho necham vyhledat taky nic, takze jsem asi uplne blbej nebo uplne v haji :)

[vencour]

zkoušel jste ty příkazy pod rootem?

[Jiri Uncovsky]

Podívej se na http://bcm43xx.berlios.de

[Ilfirin]

Ndiswrapper fw-cutter nepotřebuje, ten je potřeba na bcm43xx

[Ilfirin]

Sakra, jsem se překouk, výše napsaný zápis ingorovat :)

[Ilfirin]

Dobrý den. Řešil jsem to samé na trochu jiném stroji (A6KM) a pod 64bitem, nicméně mé poznatky

Přes všechny snahy bcm43xx mi nikdy nefungoval. Síť jsem s tím nahodil, ale dosah hrozný a spojení vypadávalo. Tudíž jsem došel k názoru že jediná volba je ndiswrapper (připojení stabilní, a dosah až na zahradu :) ). V *buntu systémech mi stačil nainstalovat ndiswrapper z repozitáře. Na jiných systémech jsem byl nucen kompilovat, ale naštěstí požadavky ndiswrapperu jsou velice malé (stačí gcc, linux headers a ještě něco tuším) takže žádná věda.

1) Je nutné sehnat si funkční ovladač ve své bitové architektuře pro Windows. To nechám na vás, google na "4318 driver" toho vyhodí dost.
2) Poté co máte sehnaný ovladač a "nějak" nainstalovaný ndiswrapper se ujistěte že modul ndiswrapper ani bcm43xx není zaveden (příkazem lsmod pro výpis a poté (samozřejmě vše s právy roota) modprobe -r modul ("modul" nahraďte názvem modulu))
3) Odstraňte předchozí ovladače z ndiswrapperu (ndiswrapper -l pro výpis a ndiswrapper -r ovladač ("ovladač" nahraďte ovladačem který se ukázal při výpisu)
4) ndiswrapper -i inffile ("inffile" nahraďte názvem souboru inf. (bcmwl5.inf a bcmwl564.sys se nejpravděpodobněji budou jmenovat soubory které potřebujete))
5) ndiswrapper -l musí ukázat nainstalovaný ovladač společně s hláškou driver installed, device present, takhle je to u mě:

ilfirin@linbook:~$ ndiswrapper -l
bcmwl5 : driver installed
        device (14E4:4318) present (alternate driver: bcm43xx)

Jakmile jedno z toho není, nepokračujte dále a zkuste jiný ovladač. Obě podmínky (installed, present) musí být splněny.
6) Pokud se povedlo, jste za vodou. Nádech... modprobe ndiswrapper .... výdech, nádech... ifconfig, iwconfig (a doufat :) )
7) třešnička na závěr, ndiswrapper -m (zapsání do configuráku modprobe)
8) úklid, zapsat bcm43xx na konec souboru /etc/modprobe.d/blacklist (zakázat nahrávání tohoto ovladače)

Snad byl návod užitečný.

[Vojtěch Trefný]

root@ubuntu:# ndiswrapper -i bcmwl5 Installing bcmwl5 couldn't copy bcmwl5 at /usr/sbin/ndiswrapper line 135.

Tohle mi to vyhodí, nevíte náhodou, co s tím?

[Ilfirin]

ndiswrapper -i bcmwl5.inf

musí být provedeno s právy roota (takže sudo ndiswrapper -i bcmwl5.inf) Co máte za distribuci?

[Vojtěch Trefný]

Jako root jsem to dělal, mám Ubuntu (6.06.1). S tím .inf to šlo, ale ndiswrapper -l mi vyhodí jen Installed ndis drivers: bcmwl5 driver present

[Ilfirin]

6.06.1 tak tam mám pocit jsem taky nějak bojoval. Zkuste ten ndiswrapper zkompilovat ale spíše bych vám doporučil update na aktuální 7.04 (zrovna na tom notebooku běží), zde je instalace bez problémů. Případně zkuste stáhnout ještě ovladač z jiného zdroje. Ta podmínka device present musí být splněna.