AbcLinuxu:/ Poradna / Linuxová poradna / 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Štítky: cache, controller, dependency, driver, error, Ethernet, For, gigabit, hardware, Intel, kernel, management, micro, msi, ovladače, PCI, PCI-E, podpora, port, POWER, problém, root, rychlost, sběrnice, sítě

Dotaz: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

6.1.2014 19:23 hermelin | skóre: 21
10Gbit sitovka - PCI Express 2.5GT vs 5GT

Přečteno: 944×

Odpovědět | Admin

Pridal jsem do serveru kartu 2x 10Gbit Supermicro-AOC-STG-i2T

Ale ovladace intelu mi hlasi ze "Speed:2.5GT/s, Width: x8, Encoding Loss:20%", pritom lspci rika ze na slotu je mozna podpora 5GT/s. Proc se teda nedomluvi na vyssi frekvenci aby byla pozadovana rychlost pokryta ? Co presne zamenaji radky na vypisu lspci "LnkCap,LnkStat" a proc jsou tam i "LnkCap2" a "LnkStat2". Predpokladam LnkCap rika jaka jsou schopnosti PCI-e sbernice a LnkStat rika jaky je aktualni stav?

Vypis "lspci -v -v":

86:00.0 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01)
        Subsystem: Super Micro Computer Inc Device 1528
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- TAbort- MAbort- >SERR- PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 42
        Region 0: Memory at cee00000 (64-bit, prefetchable) [size=2M]
        Region 4: Memory at cedfc000 (64-bit, prefetchable) [size=16K]
        Expansion ROM at cff80000 [disabled] [size=512K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [70] MSI-X: Enable+ Count=64 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00002000
        Capabilities: [a0] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
                LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [100 v2] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [140 v1] Device Serial Number a0-36-9f-ff-ff-01-b4-d0
        Capabilities: [150 v1] Alternative Routing-ID Interpretation (ARI)
                ARICap: MFVC- ACS-, Next Function: 1
                ARICtl: MFVC- ACS-, Function Group: 0
        Capabilities: [160 v1] Single Root I/O Virtualization (SR-IOV)
                IOVCap: Migration-, Interrupt Message Number: 000
                IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
                IOVSta: Migration-
                Initial VFs: 64, Total VFs: 64, Number of VFs: 64, Function Dependency Link: 00
                VF offset: 384, stride: 2, Device ID: 1515
                Supported Page Size: 00000553, System Page Size: 00000001
                Region 0: Memory at 0000000000000000 (64-bit, non-prefetchable)
                Region 3: Memory at 0000000000000000 (64-bit, non-prefetchable)
                VF Migration: offset: 00000000, BIR: 0
        Capabilities: [1d0 v1] Access Control Services
                ACSCap: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
                ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
        Kernel driver in use: ixgbe

Vypis "dmesg"

ixgbe 0000:86:00.0: (PCI Express:2.5GT/s:Width x8) 00:25:90:ca:a2:74
ixgbe 0000:86:00.0: eth2: MAC: 3, PHY: 3, PBA No: G36748-001
ixgbe 0000:86:00.0: PCI Express bandwidth of 16GT/s available
ixgbe 0000:86:00.0: (Speed:2.5GT/s, Width: x8, Encoding Loss:20%)
ixgbe 0000:86:00.0: This is not sufficient for optimal performance of this card.
ixgbe 0000:86:00.0: For optimal performance, at least 20GT/s of bandwidth is required.
ixgbe 0000:86:00.0: A slot with more lanes and/or higher speed is suggested.
ixgbe 0000:86:00.0: eth2: Enabled Features: RxQ: 8 TxQ: 8 FdirHash RSC 
ixgbe 0000:86:00.0: eth2: Intel(R) 10 Gigabit Network Connection

Nenapada nekoho v cem je problem.

Dik

Řešení dotazu:

Komentář #11 (alkoholik, 1 hlasů)

Nástroje: Začni sledovat (0) ?

Odpovědi

6.1.2014 19:38 Ruža Becelin | skóre: 40 | blog: RuzaBecelinBlog
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Co tohle?

6.1.2014 21:05 hermelin | skóre: 21
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

To bohuzel neresi problem s detekci a natavenim rychlost PCI-E sbernice. Ale pro jistotu jsem to i vyzkousel.

6.1.2014 21:46 alkoholik | skóre: 40 | blog: Alkoholik
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

A co je to za zakladni desku/chipset?

6.1.2014 23:00 hermelin | skóre: 21
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Supermicro H8QMI-2

7.1.2014 00:00 NN
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Odkaz na kartu v popisu tvrdi:

 Low-Profile, RoHS Compliant 6/6, Intel 82598EB Chipset, PB-Free

Radic 82598EB, je dle specifikacepouze PCIe v2.0 (2.5GT/s). Ale datascheetna stejne strance pod obrazkem tvrdi ze obsahuje radic X540, ktery je skutecne PCI Express* 2.1 5.0 GT/s Lane x 8. Takze jestli to neni nejaka levarna.

7.1.2014 00:22 2X4B-523P | skóre: 38 | blog: Zelezo_vs_Debian
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

v tom manuálu je, že: One (1) PCI-Express x4 slot (x8 slot using x4 signal)

tak jestli ta karta není zrovna v něm, ten druhý je One (1) PCI-Express x8 slot

jestli jsou použity oba, tak pak jeden slot zřejmě běží jen na x4 linkách a zbytek je nezapojen, někdy je tak napůl zmrzačený i druhý/třetí/čtvrtý PCI-E z x16 na x8 linek...

7.1.2014 09:01 hermelin | skóre: 21
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Tak on ovladac rika ze jede 2.5GT/s x8 takze tam asi problem neni. Podle me by ale propustnost nemela byt 2.5GT/s ale 5GT/s. Podle toho co pise lspci a jestli to dobre chapu tak PCI-e slot to umi ale z neznamyho duvodu to nepouzije. Ale jak pises muze tam bejt pri plnym osazeni dost veci zmrzacenych. Tak ted nevim jestli je chyba v desce nebo v karte pripadne jak ho donutit tech 5GT na sbernici :-)

Jinak ten popis toho cipu je asi na tech strankach blbe - urcite tam je cip X540.

7.1.2014 12:38 alkoholik | skóre: 40 | blog: Alkoholik
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Tak tohle byl orisek.
Supermicro H8QMI-2 je postavena na chipsetu nVidia MCP55 Pro, ktery odpovida nForce 590 vydane 23.5.2006.
PCI-E 2.0 specifikace byla uvedena 15.1.2007.
Uz tusis, kde je zadrhel?

7.1.2014 12:44 NN
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Ja bych relk, ze tohle je zrovna v pohode:

Capabilities: [a0] Express (v2) Endpoint, MSI 00

7.1.2014 14:48 Strejda
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Ja bych relk, ze tohle je zrovna v pohode:
Capabilities: [a0] Express (v2) Endpoint, MSI 00

Jenomže to je od karty. MCP55 Pro podle mého 5GT/s neumí. Viz:

0000:00:0d.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=2b, subordinate=2d, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fa000000-fa0fffff
    Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000
    Capabilities: [48] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+
        Address: 00000000fee00000 Data: 4071
    Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
        Mapping Address Base: 00000000fee00000
    Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
        DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
            ExtTag- RBE+ FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
            MaxPayload 128 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
        LnkCap:    Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <4us
            ClockPM- Surprise- LLActRep+ BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
        SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
            Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
        SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
            Control: AttnInd Off, PwrInd On, Power- Interlock-
        SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
            Changed: MRL- PresDet+ LinkState+
        RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
        RootCap: CRSVisible-
        RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed- WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=WRR32
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
    Capabilities: [160 v1] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UESvrt:    DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt+ RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
        CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
        CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
        AERCap:    First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    Kernel driver in use: pcieport

7.1.2014 13:19 hermelin | skóre: 21
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Taky jsem si myslel ze to treba neumi deska (PCI-E v2) - ale zase lspci to pise ze to umi tak ja nevim cemu verit. Navic jsem se pak zacal ztracet v tom podrobnem vypisu lspci takze sem nevedel co patri ke karte a co ke sbernici na desce :-(

Řešení 1× (hermelin (tazatel))

7.1.2014 14:07 alkoholik | skóre: 40 | blog: Alkoholik
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Zkus se v lspci podivat po necem jako Express PCI Express Root Port.
Ja mam u Intel G31 jasne napsane v1 a to je z Q2/2007.

7.1.2014 15:24 hermelin | skóre: 21
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Prikladam lspci celeho serveru:

00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3)
00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1)
00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2)
00:04.0 IDE interface: NVIDIA Corporation MCP55 IDE (rev a1)
00:06.0 PCI bridge: NVIDIA Corporation MCP55 PCI bridge (rev a2)
00:0a.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
00:0d.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
00:0f.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
00:19.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:19.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:19.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:19.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:19.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI ES1000 (rev 02)
03:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 07)
03:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 07)
04:03.0 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03)
04:03.1 Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03)
80:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2)
80:01.0 RAM memory: NVIDIA Corporation MCP55 LPC Bridge (rev a3)
80:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3)
80:0a.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
80:0b.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
80:0c.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
80:0d.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
80:0e.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
80:0f.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3)
81:00.0 Ethernet controller: Intel Corporation 82575EB Gigabit Network Connection (rev 02)
81:00.1 Ethernet controller: Intel Corporation 82575EB Gigabit Network Connection (rev 02)
84:00.0 RAID bus controller: Areca Technology Corp. ARC-1680 8 port PCIe/PCI-X to SAS/SATA II RAID Controller
86:00.0 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01)
86:00.1 Ethernet controller: Intel Corporation Ethernet Controller 10-Gigabit X540-AT2 (rev 01)

a ted podrobneji pro Express Bridge

80:0e.0 PCI bridge: NVIDIA Corporation MCP55 PCI Express bridge (rev a3) (prog-if 00 [Normal decode])
        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- TAbort- MAbort- >SERR- PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=80, secondary=85, subordinate=85, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- TAbort- MAbort- SERR- PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+
                Address: 00000000fee00000  Data: 4079
        Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x0, ASPM L0s L1, Latency L0 <512ns, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
                        Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=WRR32
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [160 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Kernel driver in use: pcieport

A tim je asi jasny ze proste ta deska tech 5GT/s neumi.

Dik vsem za pomoc !

Kazdopadne ta sitovka by tam ject mela ne ? Ale pojede max 16Gbit a ne 20Gbit soucasne na obou portech - hlaska toho driveru vylozene nerika ze je to spatny ale akorat ze budu mit o 20% mensi rychlost.

7.1.2014 16:05 alkoholik | skóre: 40 | blog: Alkoholik
Rozbalit Rozbalit vše Re: 10Gbit sitovka - PCI Express 2.5GT vs 5GT

Jo, pojede.

Založit nové vlákno • Nahoru

Tiskni Sdílej: