AbcLinuxu:/ Poradna / Linuxová poradna / Problem s 3 dny starym diskem:-(

Štítky: cache, data, disk, error, fdisk, For, nouveau, nVidia, problém, red, rozdělení disků, řadiče, SATA, SCSI, Seagate, tag, vga

Dotaz: Problem s 3 dny starym diskem:-(

15.10.2013 10:21 Tommy
Problem s 3 dny starym diskem:-(

Přečteno: 1075×

Odpovědět | Admin

Ahoj. Pred tydnem jsem tady resil, jaky mam koupit disk do RAID1. Nakonec jsem se rozhodl pro WD RED. Po třech dnech mi vypadl z RAIDu, nevidi ho ani fdisk a log mam plny techto hlasek:

[  891.721684]          res 40/00:1c:00:5b:38/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  891.726233] ata1.00: status: { DRDY }
[  891.728495] ata1.00: failed command: WRITE FPDMA QUEUED
[  891.730745] ata1.00: cmd 61/80:78:00:5a:38/00:00:00:00:00/40 tag 15 ncq 65536 out
[  891.730747]          res 40/00:1c:00:5b:38/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  891.735290] ata1.00: status: { DRDY }
[  891.737526] ata1: hard resetting link
[  892.336019] ata1: SATA link up unknown (SStatus 103 SControl 310)
[  892.336971] ata1.00: configured for UDMA/133
[  892.336991] ata1: EH complete
[  895.032839] ata1.00: exception Emask 0x10 SAct 0x1ff SErr 0x400000 action 0x6 frozen
[  895.033296] ata1.00: irq_stat 0x08000000, interface fatal error
[  895.035291] ata1: SError: { Handshk }
[  895.037539] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.039776] ata1.00: cmd 61/00:00:80:0b:39/01:00:00:00:00/40 tag 0 ncq 131072 out
[  895.039778]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.044340] ata1.00: status: { DRDY }
[  895.046562] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.048835] ata1.00: cmd 61/80:08:80:0c:39/00:00:00:00:00/40 tag 1 ncq 65536 out
[  895.048837]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.053363] ata1.00: status: { DRDY }
[  895.055598] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.057873] ata1.00: cmd 61/00:10:00:03:39/04:00:00:00:00/40 tag 2 ncq 524288 out
[  895.057874]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.062434] ata1.00: status: { DRDY }
[  895.064663] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.066912] ata1.00: cmd 61/00:18:00:07:39/03:00:00:00:00/40 tag 3 ncq 393216 out
[  895.066914]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.071451] ata1.00: status: { DRDY }
[  895.073697] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.075953] ata1.00: cmd 61/80:20:00:0a:39/00:00:00:00:00/40 tag 4 ncq 65536 out
[  895.075954]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.080508] ata1.00: status: { DRDY }
[  895.082751] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.085005] ata1.00: cmd 61/80:28:00:0e:39/00:00:00:00:00/40 tag 5 ncq 65536 out
[  895.085006]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.089548] ata1.00: status: { DRDY }
[  895.091772] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.094042] ata1.00: cmd 61/80:30:80:0a:39/00:00:00:00:00/40 tag 6 ncq 65536 out
[  895.094044]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.098589] ata1.00: status: { DRDY }
[  895.100828] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.103062] ata1.00: cmd 61/80:38:00:0b:39/00:00:00:00:00/40 tag 7 ncq 65536 out
[  895.103063]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.107626] ata1.00: status: { DRDY }
[  895.109864] ata1.00: failed command: WRITE FPDMA QUEUED
[  895.112123] ata1.00: cmd 61/00:40:00:0d:39/01:00:00:00:00/40 tag 8 ncq 131072 out
[  895.112125]          res 40/00:44:00:0d:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  895.116668] ata1.00: status: { DRDY }
[  895.118903] ata1: hard resetting link
[  895.600024] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  900.600021] ata1.00: qc timeout (cmd 0xec)
[  900.600027] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  900.600030] ata1.00: revalidation failed (errno=-5)
[  900.600476] ata1: hard resetting link
[  901.084017] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  911.084017] ata1.00: qc timeout (cmd 0xec)
[  911.084023] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  911.084026] ata1.00: revalidation failed (errno=-5)
[  911.084476] ata1: hard resetting link
[  911.568016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  911.568993] ata1.00: configured for UDMA/133
[  911.569008] ata1: EH complete
[  911.569045] ata1.00: exception Emask 0x10 SAct 0x3f SErr 0x1800000 action 0x6 frozen
[  911.569490] ata1.00: irq_stat 0x08000000, interface fatal error
[  911.571392] ata1: SError: { LinkSeq TrStaTrns }
[  911.573627] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.575839] ata1.00: cmd 61/00:00:00:0d:39/01:00:00:00:00/40 tag 0 ncq 131072 out
[  911.575840]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.580317] ata1.00: status: { DRDY }
[  911.582524] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.584756] ata1.00: cmd 61/80:08:00:0b:39/00:00:00:00:00/40 tag 1 ncq 65536 out
[  911.584757]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.589205] ata1.00: status: { DRDY }
[  911.591407] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.593628] ata1.00: cmd 61/80:10:80:0a:39/00:00:00:00:00/40 tag 2 ncq 65536 out
[  911.593629]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.598087] ata1.00: status: { DRDY }
[  911.600301] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.602504] ata1.00: cmd 61/80:18:00:0e:39/00:00:00:00:00/40 tag 3 ncq 65536 out
[  911.602505]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.606969] ata1.00: status: { DRDY }
[  911.609157] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.611365] ata1.00: cmd 61/80:20:00:0a:39/00:00:00:00:00/40 tag 4 ncq 65536 out
[  911.611366]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.615820] ata1.00: status: { DRDY }
[  911.618022] ata1.00: failed command: WRITE FPDMA QUEUED
[  911.620212] ata1.00: cmd 61/00:28:00:07:39/03:00:00:00:00/40 tag 5 ncq 393216 out
[  911.620214]          res 40/00:0c:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  911.624627] ata1.00: status: { DRDY }
[  911.626818] ata1: hard resetting link
[  912.108019] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  917.108019] ata1.00: qc timeout (cmd 0xec)
[  917.108025] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  917.108028] ata1.00: revalidation failed (errno=-5)
[  917.108471] ata1: hard resetting link
[  917.592019] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  917.593025] ata1.00: configured for UDMA/133
[  917.593042] ata1: EH complete
[  917.593127] ata1.00: exception Emask 0x10 SAct 0x1ff SErr 0x1c00000 action 0x6 frozen
[  917.593568] ata1.00: irq_stat 0x08000000, interface fatal error
[  917.595445] ata1: SError: { Handshk LinkSeq TrStaTrns }
[  917.597655] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.599852] ata1.00: cmd 61/00:00:00:07:39/03:00:00:00:00/40 tag 0 ncq 393216 out
[  917.599853]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.604265] ata1.00: status: { DRDY }
[  917.606454] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.608665] ata1.00: cmd 61/80:08:00:0a:39/00:00:00:00:00/40 tag 1 ncq 65536 out
[  917.608667]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.613086] ata1.00: status: { DRDY }
[  917.615274] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.617489] ata1.00: cmd 61/80:10:00:0e:39/00:00:00:00:00/40 tag 2 ncq 65536 out
[  917.617490]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.621895] ata1.00: status: { DRDY }
[  917.624105] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.626290] ata1.00: cmd 61/80:18:80:0a:39/00:00:00:00:00/40 tag 3 ncq 65536 out
[  917.626292]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.630722] ata1.00: status: { DRDY }
[  917.632948] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.635118] ata1.00: cmd 61/80:20:00:0b:39/00:00:00:00:00/40 tag 4 ncq 65536 out
[  917.635120]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.639537] ata1.00: status: { DRDY }
[  917.641716] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.643913] ata1.00: cmd 61/00:28:00:0d:39/01:00:00:00:00/40 tag 5 ncq 131072 out
[  917.643915]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.648336] ata1.00: status: { DRDY }
[  917.650517] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.652735] ata1.00: cmd 61/00:30:00:03:39/04:00:00:00:00/40 tag 6 ncq 524288 out
[  917.652737]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.657140] ata1.00: status: { DRDY }
[  917.659315] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.661532] ata1.00: cmd 61/80:38:80:0c:39/00:00:00:00:00/40 tag 7 ncq 65536 out
[  917.661533]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.665959] ata1.00: status: { DRDY }
[  917.668179] ata1.00: failed command: WRITE FPDMA QUEUED
[  917.670392] ata1.00: cmd 61/00:40:80:0b:39/01:00:00:00:00/40 tag 8 ncq 131072 out
[  917.670394]          res 40/00:24:00:0b:39/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[  917.674850] ata1.00: status: { DRDY }
[  917.677075] ata1: hard resetting link
[  918.160018] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  918.160532] ata1.00: failed to set xfermode (err_mask=0x100)
[  923.160018] ata1: hard resetting link
[  923.644018] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  928.644017] ata1.00: qc timeout (cmd 0xec)
[  928.644023] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  928.644026] ata1.00: revalidation failed (errno=-5)
[  928.644464] ata1: hard resetting link
[  929.128014] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  939.128017] ata1.00: qc timeout (cmd 0xec)
[  939.128023] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  939.128026] ata1.00: revalidation failed (errno=-5)
[  939.128457] ata1.00: disabled
[  939.128478] ata1: hard resetting link
[  939.612016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  939.612032] ata1: EH complete
[  939.612053] sd 0:0:0:0: [sda] Unhandled error code
[  939.612055] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.612058] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0b 80 00 01 00 00
[  939.612066] end_request: I/O error, dev sda, sector 3738496
[  939.612472] raid1: Disk failure on sda2, disabling device.
[  939.612474] raid1: Operation continuing on 1 devices.
[  939.616545] sd 0:0:0:0: [sda] Unhandled error code
[  939.616547] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.616550] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0c 80 00 00 80 00
[  939.616557] end_request: I/O error, dev sda, sector 3738752
[  939.618691] sd 0:0:0:0: [sda] Unhandled error code
[  939.618693] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.618696] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 03 00 00 04 00 00
[  939.618703] end_request: I/O error, dev sda, sector 3736320
[  939.620892] sd 0:0:0:0: [sda] Unhandled error code
[  939.620894] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.620897] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0d 00 00 01 00 00
[  939.620904] end_request: I/O error, dev sda, sector 3738880
[  939.622856] sd 0:0:0:0: [sda] Unhandled error code
[  939.622859] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.622862] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0b 00 00 00 80 00
[  939.622868] end_request: I/O error, dev sda, sector 3738368
[  939.624949] sd 0:0:0:0: [sda] Unhandled error code
[  939.624951] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.624954] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0a 80 00 00 80 00
[  939.624961] end_request: I/O error, dev sda, sector 3738240
[  939.626995] sd 0:0:0:0: [sda] Unhandled error code
[  939.626997] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.627000] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0e 00 00 00 80 00
[  939.627007] end_request: I/O error, dev sda, sector 3739136
[  939.629048] sd 0:0:0:0: [sda] Unhandled error code
[  939.629050] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.629053] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0a 00 00 00 80 00
[  939.629059] end_request: I/O error, dev sda, sector 3738112
[  939.631057] sd 0:0:0:0: [sda] Unhandled error code
[  939.631059] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.631062] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 07 00 00 03 00 00
[  939.631068] end_request: I/O error, dev sda, sector 3737344
[  939.633079] sd 0:0:0:0: [sda] Unhandled error code
[  939.633081] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.633084] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 39 0e 80 00 04 00 00
[  939.633091] end_request: I/O error, dev sda, sector 3739264
[  939.635040] sd 0:0:0:0: [sda] Unhandled error code
[  939.635042] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.635045] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 e8 da 7d 00 00 00 08 00
[  939.635052] end_request: I/O error, dev sda, sector 3906632960
[  939.636914] end_request: I/O error, dev sda, sector 3906632960
[  939.638793] md: super_written gets error=-5, uptodate=0
[  939.639088] md: md1: recovery done.
[  939.639523] sd 0:0:0:0: [sda] READ CAPACITY(16) failed
[  939.639526] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.639529] sd 0:0:0:0: [sda] Sense not available.
[  939.639551] sd 0:0:0:0: [sda] READ CAPACITY failed
[  939.639553] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  939.639556] sd 0:0:0:0: [sda] Sense not available.
[  939.639587] sd 0:0:0:0: [sda] Asking for cache data failed
[  939.640681] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  939.642601] sda: detected capacity change from 2000398934016 to 0
[  939.870509] RAID1 conf printout:
[  939.870513]  --- wd:1 rd:2
[  939.870517]  disk 0, wo:1, o:0, dev:sda2
[  939.870520]  disk 1, wo:0, o:1, dev:sdb2
[  939.870522] RAID1 conf printout:
[  939.870523]  --- wd:1 rd:2
[  939.870525]  disk 1, wo:0, o:1, dev:sdb2
[ 1178.273762] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1178.285951] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1178.285992] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1178.286005] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1238.132096] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1238.132122] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1238.132138] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1238.132150] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1298.354097] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1298.354122] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1298.354137] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1298.354148] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1598.277466] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1598.277491] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1598.277506] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1598.277517] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1829.752018] [drm] nouveau 0000:00:12.0: Setting dpms mode 1 on vga encoder (output 0)
[ 1897.954560] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1897.954585] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1897.954600] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 1897.954612] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 2198.089138] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 2198.089163] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 2198.089178] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO
[ 2198.089190] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO

Je problem opravdu s diskem nebo to muze byt deskou (radicem)? Ale na te same mam puvodni Seagate a ten jede /zatim/ v pohode. Mam ho reklamovat?

Diky moc.

Nástroje: Začni sledovat (2) ?

Odpovědi

15.10.2013 10:28 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

smartctl -d sat -a /dev/sda

vypise co? Je mozne, ze pro provedeni toho prikazu muze byt potreba nejprve masinu restartovat, aby se disk opet chytil.

15.10.2013 10:33 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Tak restartuju a pak poslu vypis. Snad se tam ten disk zase ukaze.

15.10.2013 10:39 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD20EFRX-68EUZN0
Serial Number:    WD-WCC4M0120830
Firmware Version: 80.00A80
User Capacity:    2 000 398 934 016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   9
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Tue Oct 15 10:38:24 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (27720) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 255) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x703d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   100   253   021    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       2
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       113
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       2
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0022   110   103   000    Old_age   Always       -       37
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       2
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

15.10.2013 10:45 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

viz komentar dole, je to kabel:

199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       2

15.10.2013 10:39 Luboš Doležel (Doli) | skóre: 98 | blog: Doliho blog | Kladensko
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Je kabel zapojený dobře?

15.10.2013 10:49 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Doufám, že ano. Teď nemám k serveru přístup, podívám se večer. Ale zapojoval jsem ho v sobotu ráno a do dnešního rána vše jelo ok a se serverem nikdo nemanipuloval.

15.10.2013 10:53 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

vadny kabel (pokud tedy neni uplne preseknuty) se projevuje prave takto, ze dochazi k vypadkum v datech. Naprostou vetsinu dokaze odchytit CRC a tak neni problem zaznamenan, az kdyz uz to CRC nezvladne. Doporucuju ten kabel vymenit za novy.

15.10.2013 11:38 Petr Šobáň | skóre: 80 | blog: soban | Olomouc
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Přesně vypadá to na kabel takže dát nový a skontrolovat konektory na MB a HDD.

15.10.2013 11:43 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

To jste mě potěšili, tak snad to bude ono :-)

Ale jak říkám, zajímavé je, že ty 3 dny to jelo bez sebemenších problémů. Synchronizace RAIDu atd.. Ale stát se může cokoliv. Díky, dám vědět, jak jsem dopadl.

15.10.2013 11:45 Josef Kufner | skóre: 70
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Disky a ventilátory vytvářejí vibrace, které mohly uvolnit mizerný spoj a prostě jim to chvíli trvalo.

Hello world ! Segmentation fault (core dumped)

15.10.2013 12:14 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Taky mě to pak docvaklo, že by to mohlo být vibracema :-)

15.10.2013 11:48 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Ještě se zeptám k tomu kabelu. Mám jich doma spousty použitých, ale nemám koupit radši nějaký nový. Existuje nějaký lepší, nebo je to úplně fuk?

15.10.2013 11:54 Josef Kufner | skóre: 70
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Neber ten nejlevnější. Použitý nebo nový, na tom nezáleží. Hlavně aby byl v pořádku a nebyl to ošizený šmejd.

Hello world ! Segmentation fault (core dumped)

15.10.2013 12:13 R
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Daj tam lubovolny pouzity a sleduj, co bude robit. Ja som sa stretol s vadnym kablom prave novym.

15.10.2013 12:15 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Tak jo, nějaký tam dám a snad se trefím a bude to fachčit :-)

15.10.2013 13:22 Petr Šobáň | skóre: 80 | blog: soban | Olomouc
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

V kabelu bývá většinou zrada u konektoru, ty pružinky už nepruží a povrchová koroze taky dělá svoje....

Prostě si poznač že ten kabel blbl a dej druhej když to bude OK tak byla zrada v kabelu a ten vadný vyhoď.

15.10.2013 13:59 R
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Odkedy zlato koroduje?

15.10.2013 15:03 Josef Kufner | skóre: 70
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Ty máš pozlacené všechny SATA konektory? A určitě není v místě kontaktu kousek zlata sedřený? Nebo tam není chycený kousek prachu? Hm? ;-)

Hello world ! Segmentation fault (core dumped)

15.10.2013 18:31 Petr Šobáň | skóre: 80 | blog: soban | Olomouc
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Od té doby co nejsou kontakty ze zlata :-)

né všechny konektory a pružinky jsou pozlacené!

A i pozlacený kontakt může blbnout - nemusí mít dobrý přítlak - únava pružiny.

A taky se láme kabel u průchodky z konektoru :-)

16.10.2013 22:01 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Tak jsem vymenil kabel, nakonec i desku a je to porad stejne :-(

17.10.2013 00:46 Josef Kufner | skóre: 70
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Disk důkladně přemaž náhodnými daty (nebo kladivem) a reklamuj (nebo si z něj udělej nástěné hodiny).

Hello world ! Segmentation fault (core dumped)

17.10.2013 05:57 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Presne, je to k vzteku. Disk, ktery ma vydrzet vic nez klasicky, vydrzel jen par dni:-/ Jde do reklamace, doufam, ze mi to uznaji.

17.10.2013 14:13 Petr Šobáň | skóre: 80 | blog: soban | Olomouc
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

No co s tím to nasere.....

17.10.2013 14:37 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

aktualni vystup

smartctl -d sat -a /dev/sda

po tech vymenach by byl k dispozici?

17.10.2013 14:48 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Jeste poznamka, spise nez desku je potreba vyzkouset jiny (vykonnejsi) napajeci zdroj. Viz treba diagnostika vysvetlena zde.

17.10.2013 21:47 Tommy
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Tady:

smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD20EFRX-68EUZN0
Serial Number:    WD-WCC4M0120830
Firmware Version: 80.00A80
User Capacity:    2 000 398 934 016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   9
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Oct 17 21:46:53 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 (27720) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 255) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x703d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   174   174   021    Pre-fail  Always       -       4266
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       10
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       168
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       10
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       6
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       3
194 Temperature_Celsius     0x0022   116   103   000    Old_age   Always       -       31
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       2
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       118         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute dela

17.10.2013 22:03 Milan Roubal | skóre: 25
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Ty hodnoty ukazuji na zdravy disk (ale stale je to pouze smart, chyba muze byt i v disku). Hodnota UDMA_CRC_Error_Count se nezvetsila, coz je dobre znameni. Ted bych se zameril spise na zdroj.

Pro porovnani vypis hodnot z meho WD RED disku.

> smartctl -d sat -a /dev/sda
smartctl 5.42 2011-10-20 r3458 [armv5tel-linux-2.6.32.12] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD30EFRX-68AX9N0
Serial Number:    WD-XXXXXXXXXXX
LU WWN Device Id: 5 0014ee 058c81985
Firmware Version: 80.00A80
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  ACS-2 (revision not indicated)
Local Time is:    Thu Oct 17 21:53:53 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (40980) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 255) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x70bd) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   179   175   021    Pre-fail  Always       -       6041
  4 Start_Stop_Count        0x0032   098   098   000    Old_age   Always       -       2295
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   093   093   000    Old_age   Always       -       5202
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1214
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       19
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       2275
194 Temperature_Celsius     0x0022   108   103   000    Old_age   Always       -       42
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      5197         -
# 2  Short offline       Completed without error       00%      5187         -
# 3  Short offline       Completed without error       00%      5180         -
# 4  Extended offline    Completed without error       00%      5173         -
# 5  Short offline       Completed without error       00%      5151         -
# 6  Short offline       Completed without error       00%      5137         -
# 7  Short offline       Completed without error       00%      5127         -
# 8  Short offline       Completed without error       00%      5118         -
# 9  Short offline       Completed without error       00%      5112         -
#10  Short offline       Completed without error       00%      5107         -
#11  Extended offline    Completed without error       00%      5103         -
#12  Short offline       Completed without error       00%      5088         -
#13  Short offline       Completed without error       00%      5082         -
#14  Short offline       Completed without error       00%      5072         -
#15  Short offline       Completed without error       00%      5044         -
#16  Short offline       Completed without error       00%      5022         -
#17  Short offline       Completed without error       00%      4995         -
#18  Extended offline    Completed without error       00%      4977         -
#19  Short offline       Completed without error       00%      4947         -
#20  Short offline       Completed without error       00%      4928         -
#21  Short offline       Completed without error       00%      4921         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

17.10.2013 21:58 2013
Rozbalit Rozbalit vše Re: Problem s 3 dny starym diskem:-(

Na jadre 2.6.32 ti to nebude davat ziadne chyby. Podobna skusenost.

Založit nové vlákno • Nahoru

Tiskni Sdílej: