hdparm -Tt - aké sú Vaše hodnoty? UPDATE

25.1.2008 19:35 | 6 | poslední úprava: 26.1.2008 12:51

Tak ma zaujíma, pre porovnanie, aké hodnoty vám hdparm -Tt /dev/(hard_disk) vyhadzuje (kľudne hádžte aj hodnoty raidov).

2,5" 80G SATA HDD (WDC WD800BEVS-22RST0), AHCI mód, Debian Etch 2.6.18

/dev/sda:
Timing cached reads: 1378 MB in 2.00 seconds = 688.98 MB/sec
Timing buffered disk reads: 86 MB in 3.03 seconds = 28.37 MB/sec

UPDATE

2,5" 80G SATA HDD (WDC WD800BEVS-22RST0), AHCI mód, Debian Etch 2.6.24-custom

/dev/sda:
 Timing cached reads:   1772 MB in  2.00 seconds = 886.32 MB/sec
 Timing buffered disk reads:  106 MB in  3.02 seconds =  35.07 MB/sec

       

Komentáře

[atan]

HW RAID10

hdparm -tT /dev/sda3

/dev/sda3:

Timing cached reads: 2372 MB in 2.00 seconds = 1185.69 MB/sec

Timing buffered disk reads: 432 MB in 3.01 seconds = 143.53 MB/sec

[Jan Trávníček]

/dev/sda: Timing cached reads: 1860 MB in 2.00 seconds = 931.01 MB/sec Timing buffered disk reads: 114 MB in 3.04 seconds = 37.56 MB/sec

2,5" 100GB SATA (hitachi tavelstar 5K100) Archlinux

AHCI nemam je to na škodu?

[Michal Fecko]

AHCI je dobré využívať namiesto IDE/compatible módu napr. kôli NCQ alebo hot-plugingu.

[Jan Trávníček]

Diky diky povolim si.

[andree]

WDC WD2500BEVE-00WZT0 (ATA-133, alebo 100? :o))) Timing cached reads: 782 MB in 2.39 seconds = 326.77 MB/sec Timing buffered disk reads: 178 MB in 3.01 seconds = 59.23 MB/sec

ale ked uz chces porovnavat, neviem ci je toto najlepsi sposob...

[David Jaša]

# hdparm -iTt /dev/sda

/dev/sda:

 Model=ST96812A                                , FwRev=3.04    , SerialNo=            5PJ04HS7
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1,2,3,4,5,6

 * signifies the current active mode

 Timing cached reads:   808 MB in  2.00 seconds = 403.65 MB/sec
 Timing buffered disk reads:  112 MB in  3.01 seconds =  37.24 MB/sec

[honzulak1]

2,5" 120GB PATA Seagate Momentus ST9120822A

hdparm -tT /dev/sda

/dev/sda:
 Timing cached reads:   972 MB in  2.00 seconds = 485.92 MB/sec
 Timing buffered disk reads:  122 MB in  3.03 seconds =  40.26 MB/sec

[Integral]

Jestli te to zajima, tak tady jsou moje hodnoty disk : WD Scorpio WD1600BEVS, SATA, 160GB, 5400 rpm - jedna se o maly notebookovy disk
system: arch
/dev/sda6: Timing cached reads: 1598 MB in 2.00 seconds = 799.50 MB/sec Timing buffered disk reads: 106 MB in 3.04 seconds = 34.87 MB/sec
/dev/sda8: Timing cached reads: 1592 MB in 2.00 seconds = 796.57 MB/sec Timing buffered disk reads: 98 MB in 3.01 seconds = 32.52 MB/sec
/dev/sda1: Timing cached reads: 1608 MB in 2.00 seconds = 804.35 MB/sec Timing buffered disk reads: 136 MB in 3.03 seconds = 44.96 MB/sec
(Jeste by me zajimalo, co presne tento programek otestuje - jak vidno, vysledky zrejme nezavisi na filesystemu [nejlepsi vysledek dal disk, ktery je primarni a je ntfs a pri testovani se vytizeni procesu mount-3g (nebo tak nejak) vubec nezvysilo ])

[frdrx]

Model=WDC WD2500KS-00MJB /dev/sda1:

Timing cached reads: 1526 MB in 2.00 seconds = 763.37 MB/sec

Timing buffered disk reads: 100 MB in 2.80 seconds = 35.75 MB/sec

[JoVY]

SEAGATE Momentus 160GB, 7200ot., S-ATA-II, 8MB, 2.5", NCQ, G-Force (ST9160823ASG), AHCI mód /dev/sda:
Timing cached reads: 5060 MB in 2.00 seconds = 2533.40 MB/sec
Timing buffered disk reads: 146 MB in 3.02 seconds = 48.42 MB/sec

[David Watzke]

Seagate Barracudy...

# hdparm -itT /dev/sd[abc]

/dev/sda:

 Model=ST3320620AS                             , FwRev=3.AAC   , SerialNo=            5QF00SY8
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1012 MB in  2.00 seconds = 505.59 MB/sec
 Timing buffered disk reads:  224 MB in  3.01 seconds =  74.54 MB/sec

/dev/sdb:

 Model=ST3160021A                              , FwRev=8.01    , SerialNo=3LJ36A7L
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1,2,3,4,5,6

 * signifies the current active mode

 Timing cached reads:   1008 MB in  2.00 seconds = 503.85 MB/sec
 Timing buffered disk reads:  166 MB in  3.02 seconds =  54.96 MB/sec

/dev/sdc:

 Model=ST380011A                               , FwRev=3.06    , SerialNo=3JV5T649
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1,2,3,4,5,6

 * signifies the current active mode

 Timing cached reads:   1062 MB in  2.00 seconds = 530.29 MB/sec
 Timing buffered disk reads:  164 MB in  3.02 seconds =  54.38 MB/sec

[Cohen]

SAL:~ # hdparm -itT /dev/hda

/dev/hda:

 Model=ST340014A, FwRev=8.54, SerialNo=5JVLH8WV
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

 * signifies the current active mode

 Timing cached reads:   1288 MB in  2.00 seconds = 642.62 MB/sec
 Timing buffered disk reads:   92 MB in  3.02 seconds =  30.48 MB/sec

SAL:~ # hdparm -itT /dev/sda

/dev/sda:

 Model=SAMSUNG SP1614C                         , FwRev=SW100-30, SerialNo=S01XJ10X821398
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
 BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: (null):  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

 * signifies the current active mode

 Timing cached reads:   1248 MB in  2.00 seconds = 623.82 MB/sec
 Timing buffered disk reads:  154 MB in  3.03 seconds =  50.79 MB/sec
SAL:~ #

S tím, že na hda je běžící systém i data a zrovna se na něj zapisuje DVB-T stream. Jinak byly disky při měření v klidu (kromě systémových věcí běžících na pozadí).

[Honza "tux" Friesse]

2x WD (normální desktop disky)

root@daemon:/home/honza# hdparm -tT /dev/sda

/dev/sda:
 Timing cached reads:   2868 MB in  2.00 seconds = 1434.13 MB/sec
 Timing buffered disk reads:  174 MB in  3.03 seconds =  57.36 MB/sec
root@daemon:/home/honza# hdparm -tT /dev/hda

/dev/hda:
 Timing cached reads:   2596 MB in  2.00 seconds = 1298.78 MB/sec
 Timing buffered disk reads:  200 MB in  3.00 seconds =  66.65 MB/sec

[Kvakor]

/dev/hda:

 Model=ST3120023A, FwRev=3.33, SerialNo=3KA1B1RF
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

 * signifies the current active mode

 Timing cached reads:   1674 MB in  2.00 seconds = 836.47 MB/sec
 Timing buffered disk reads:  100 MB in  3.01 seconds =  33.24 MB/sec


/dev/sda:

 Model=HDT722525DLA380                         , FwRev=V44OA91A, SerialNo= VDK41BT4D554YK
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
 BuffType=DualPortCache, BuffSize=7674kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1:  ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

 * signifies the current active mode

 Timing cached reads:   1672 MB in  2.00 seconds = 836.39 MB/sec
 Timing buffered disk reads:  202 MB in  3.02 seconds =  66.87 MB/sec

Oba disky jsou pripojene k radici v southbridgy VIA VT8237, prvni je PATA, druhy SATA.

[2008]

SW RAID0

/dev/md6:
Timing cached reads:   8844 MB in  2.00 seconds = 4425.86 MB/sec
Timing buffered disk reads:  466 MB in  3.00 seconds = 155.12 MB/sec

[thingie]

No jaké asi. Vyšší. Kurva vyšší. Halík!

[Mrkva]

/dev/sda: Timing cached reads: 1536 MB in 2.00 seconds = 767.75 MB/sec Timing buffered disk reads: 120 MB in 3.02 seconds = 39.71 MB/sec Device Model: FUJITSU MHW2120BH (AHCI)

[Honza]

# /sbin/hdparm -iTt /dev/sda2

/dev/sda2:

 Model=SAMSUNG HD501LJ                         , FwRev=CR100-12, SerialNo=S0MUJ1NQ112975      
 Config={ Fixed }
 RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
 BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=?0?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: unknown:  ATA/ATAPI-3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   9328 MB in  2.00 seconds = 4672.05 MB/sec
 Timing buffered disk reads:  260 MB in  3.00 seconds =  86.53 MB/sec

[Ondřej Kuda]

hdparm -iTt /dev/hda
Password:

/dev/hda:

 Model=ST3320620A, FwRev=3.AAE, SerialNo=9QF5JXTQ
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=off
 CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

 * signifies the current active mode

 Timing cached reads:   2044 MB in  2.00 seconds = 1021.03 MB/sec
 Timing buffered disk reads:  190 MB in  3.01 seconds =  63.19 MB/sec

[herne the hunter]

/dev/hda:
Timing cached reads: 324 MB in 2.00 seconds = 161.97 MB/sec
Timing buffered disk reads: 168 MB in 3.03 seconds = 55.37 MB/sec

hergot, proč mi -T dává tak málo? nemám tady někde nějakej čudlík, kterej by to moh' spravit? a jestli ne, tak proč ne?!

[David Watzke]

Single-channel (64-bit) DDR?

[herne the hunter]

chacha, kde by se to tam vzalo, tam jsou ještě SDRAMky nebo jak se jim říkávalo ;)

[David Watzke]

Tak není divu. Ale ber to z tý lepší stránky, máš swap skoro stejně rychlej jako RAM

[Michal Fecko]

[Prcek]

Taky mam podobnou "sunku"
Duron 900, VIA KT133, Samsung 80 GB (buffer 8 MB)

/dev/hda:
 Timing cached reads:   260 MB in  2.01 seconds = 129.07 MB/sec
 Timing buffered disk reads:  150 MB in  3.07 seconds =  48.89 MB/sec

[Kyosuke]

SDRAMy všichni používáme dodnes. Tedy kromě těch nešťastníků, co ještě mají RDRAMí desky pro P4.

[Kvakor]

A co cache? A dava Bogomips cislo, ktere by melo? U vetsiny dnesnich proceosru je to cca. 2*frekvence.

[herne the hunter]

nj, už jsem si to přečet v manuálu, to je propustnost celýho systému. není divu, že se ta moje šunka na víc nezmůže…

[Zdeněk Burda]

Hitachi HDT725050VLA360 Timing cached reads: 7602 MB in 2.00 seconds = 3806.86 MB/sec
Timing buffered disk reads: 222 MB in 3.02 seconds = 73.50 MB/sec

[frEon]

notebookova dva a pulka,
hdparm -itT /dev/sda /dev/sda: Model=Hitachi HTS541616J9SA00 , FwRev=SB4OC7BP, SerialNo= SB2404SJKMVJYE Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4 BuffType=DualPortCache, BuffSize=7516kB, MaxMultSect=16, MultSect=?0? CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1: ATA/ATAPI-2,3,4,5,6,7 * signifies the current active mode Timing cached reads: 5618 MB in 2.00 seconds = 2815.31 MB/sec Timing buffered disk reads: 138 MB in 3.02 seconds = 45.65 MB/sec

[frEon]

sorry, sem dement

hdparm -itT /dev/sda

/dev/sda:

 Model=Hitachi HTS541616J9SA00                 , FwRev=SB4OC7BP, SerialNo=      SB2404SJKMVJYE
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=DualPortCache, BuffSize=7516kB, MaxMultSect=16, MultSect=?0?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1:  ATA/ATAPI-2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   5618 MB in  2.00 seconds = 2815.31 MB/sec
 Timing buffered disk reads:  138 MB in  3.02 seconds =  45.65 MB/sec

[Michal Fecko]

hmmm, 5400rpms - to ja mam tiez, a tebe ide 45 MB/s mne 28 MB/s Neide mi o to mat rychlejsi vysledok ako ty, ale to je rozdiel 15 MB/s co mi pride dost. Asi by sa to zlepsilo 7200kovou 2,5kou, ale zase ta by viac hriala... O cached reads ani nevravim

[David Jaša]

Někde máš něco špatně. Výš je můj výsledek - něco přes 37 MB/s a to je Seagate Momentus 5400.2 na ATA (ICH4).

[Michal Fecko]

Mozno koli WD, osobne preferujem SG, ale moj notebook uz prisiel s WD tak som ho teda nemenil,,, ake prepinace skusit na "tuning" pomocou hdparmu? a co sdparm? SATA disk cez AHCI sa povazuje alebo nepovazuje za SCSI?

[David Jaša]

Spíš něco v konfiguraci řadiče nebo taky mohl nějaký proces zapisovat zrovna když jsi měřil. Tuning nemám žádný, toto je výchozí Ubuntu 7.10. A od té doby, co se v kernelu stará libata i o ATA disky, tak už žádné ne-scsi disky nemáme.

[Michal Fecko]

Mam Debian Etch s 2.6.18 kernelom, skúsim skompilovať 2.6.24ku ako sa to bude spravať

[frEon]

jo, ten disk je pekne rychlej, ale vsiml jsem ze mi na nem zacinaj pomalu degradovat data a po blizsim zkoumani jsem objevil vadny sektory... no o kvalite disku to snad nic nevypovida, muze to byt treba tim jak mi spadl zapnuty notebook z postele (lezim, je noc, programuju, najednou rana jak z dela, koukam, venku svetlo a notebook na zemi ).

[frEon]

jeste par disku:

hdparm -itT /dev/hdd

/dev/hdd:

 Model=ST3300831A, FwRev=3.03, SerialNo=3NF1AXY7
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=off
 CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1374 MB in  2.00 seconds = 686.72 MB/sec
 Timing buffered disk reads:   90 MB in  3.06 seconds =  29.44 MB/sec

 hdparm -itT /dev/hda

/dev/hda:

 Model=WDC WD1600JB-00GVA0, FwRev=08.02D08, SerialNo=WD-WCALL1177129
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
 BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=off
 CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6

 * signifies the current active mode

 Timing cached reads:   1372 MB in  2.00 seconds = 685.83 MB/sec
 Timing buffered disk reads:  160 MB in  3.02 seconds =  53.05 MB/sec

tenhle disk odmita vypsat co je zac... takze to povim za nej . Western Digital WD5000AAKS

 hdparm -itT /dev/sda

/dev/sda:
 HDIO_GET_IDENTITY failed: Inappropriate ioctl for device
 Timing cached reads:   1376 MB in  2.00 seconds = 687.84 MB/sec
 Timing buffered disk reads:  218 MB in  3.02 seconds =  72.27 MB/sec

[Milan Lajtoš]

[root@babraq]# hdparm -tT /dev/sda

/dev/sda: Timing cached reads: 6678 MB in 2.00 seconds = 3347.32 MB/sec Timing buffered disk reads: 132 MB in 3.04 seconds = 43.37 MB/sec

A povie mi niekto co to vlastne znamena..? Prosim..

[Václav Kramář]

$ sudo hdparm -iTt /dev/sda

/dev/sda:

 Model=ST3120022A                              , FwRev=3.06    , SerialNo=3JS1DPLR            
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=?16?
 CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=234441648
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:  ATA/ATAPI-1,2,3,4,5,6

 * signifies the current active mode

 Timing cached reads:   206 MB in  2.00 seconds = 102.98 MB/sec
 Timing buffered disk reads:  152 MB in  3.00 seconds =  50.60 MB/sec

[Václav Kramář]

Po upgradu:

sudo hdparm -Tti /dev/sda

/dev/sda:

 Model=Hitachi HCS721616PLA380                 , FwRev=P22OABEA, SerialNo=      PVE331Z9TN4UTU
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
 BuffType=DualPortCache, BuffSize=7657kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1:  ATA/ATAPI-2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   2002 MB in  2.00 seconds = 1001.41 MB/sec
 Timing buffered disk reads:  222 MB in  3.00 seconds =  73.93 MB/sec

[3of5]

root@Lenka:/# hdparm -iTt /dev/hda

/dev/hda:

 Model=WDC WD600VE-00KWT0, FwRev=01.03K01, SerialNo=WD-WXE706142049
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=56
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   440 MB in  2.00 seconds = 219.63 MB/sec
 Timing buffered disk reads:   98 MB in  3.00 seconds =  32.66 MB/sec

K cemu ti to bude?

[Michal Fecko]

K cemu ti to bude?

Len tak pre porovnanie, snáď aj pre priemerné/max. hodnoty namerané užívateľmi abcčka.

[_radek]

Seagate ST3320620AS
 Timing cached reads:   2628 MB in  2.00 seconds = 1314.53 MB/sec
 Timing buffered disk reads:  230 MB in  3.00 seconds =  76.56 MB/sec

Samsung HD501LJ
 Timing cached reads:   2522 MB in  2.00 seconds = 1261.01 MB/sec
 Timing buffered disk reads:  250 MB in  3.01 seconds =  83.05 MB/sec

[JZD]

notebook, dvaapůlka

hdparm -iTt /dev/sda

/dev/sda:

 Model=SAMSUNG HM100JC                         , FwRev=YN100-11, SerialNo=S0CFJ10YB94095
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
 BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=195371568
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 0:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1650 MB in  2.00 seconds = 824.93 MB/sec
 Timing buffered disk reads:   94 MB in  3.03 seconds =  30.98 MB/sec

[tom112233]

Seagate Barracuda 7200.10 SATA:

 Timing cached reads:   2358 MB in  2.00 seconds = 1179.63 MB/sec
 Timing buffered disk reads:  238 MB in  3.02 seconds =  78.79 MB/sec

Western Digital Caviar ATA:

 Timing cached reads:   2398 MB in  2.00 seconds = 1199.86 MB/sec
 Timing buffered disk reads:  170 MB in  3.03 seconds =  56.02 MB/sec

[Andrej]

LVM2 striping přes 2 SCSI disky, 10000 otáček za minutu:

Timing cached reads:   484 MB in  2.01 seconds = 241.30 MB/sec
Timing buffered disk reads:  318 MB in  3.02 seconds = 105.45 MB/sec

Disk pro notebook, IDE, 7200 otáček za minutu:

Timing cached reads:   738 MB in  2.00 seconds = 368.35 MB/sec
Timing buffered disk reads:  136 MB in  3.03 seconds =  44.87 MB/sec

[koulinek]

hdparm -itT /dev/sda

/dev/sda:

 Model=WDC WD360ADFD-00NLR1                    , FwRev=20.07P20, SerialNo=     WD-WMANT1104983
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=48
 BuffType=DualPortCache, BuffSize=16384kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=72303840
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 published, ANSI INCITS 397-2005:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   8850 MB in  2.00 seconds = 4431.14 MB/sec
 Timing buffered disk reads:  250 MB in  3.02 seconds =  82.72 MB/sec

[Jimmy]

Notebook, P3 800, 2,5" Hitachi 100 GB 7200 ot

hdparm -iTt /dev/hda

/dev/hda:

Model=HTS721010G9AT00, FwRev=MCZOA51A, SerialNo=MPC0B2Y0GMG2BE Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4 BuffType=DualPortCache, BuffSize=7539kB, MaxMultSect=16, MultSect=off CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=195371568 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a: ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

* signifies the current active mode

Timing cached reads: 660 MB in 2.00 seconds = 329.32 MB/sec
Timing buffered disk reads: 152 MB in 3.04 seconds = 50.06 MB/sec

[Jimmy]

VIA C7-D 1,5 GHz

Model=HTS541040G9AT00 - Hitachi Travelstar 2,5" 40 GB 5400 ot

Timing cached reads: 500 MB in 2.01 seconds = 249.31 MB/sec
Timing buffered disk reads: 110 MB in 3.05 seconds = 36.11 MB/sec

Model=ST3750640AS - SEAGATE Barracuda 750GB 16MB SATA

Timing cached reads: 498 MB in 2.00 seconds = 248.66 MB/sec
Timing buffered disk reads: 230 MB in 3.01 seconds = 76.34 MB/sec

Model=WDC WD5000KS-00MNB0 - WD Caviar SE16 500GB

Timing cached reads: 500 MB in 2.00 seconds = 249.63 MB/sec
Timing buffered disk reads: 208 MB in 3.01 seconds = 69.06 MB/sec

[Jimmy]

VIA C3 1GHz (deska M10000) - strojek na hraní

Model=WDC WD600AB-22CBA0 - Western Digital 60 GB 3,5" 5400ot

Timing cached reads: 218 MB in 2.01 seconds = 108.64 MB/sec
Timing buffered disk reads: 108 MB in 3.01 seconds = 35.93 MB/sec

[Jimmy]

P2 400 MHz - router

Model=WDC AC28400R - Western Digital 8 GB 3,5"

UDMA modes: udma0 udma1 *udma2 udma3 udma4

Timing buffer-cache reads: 480 MB in 2.01 seconds = 239.32 MB/sec
Timing buffered disk reads: 38 MB in 3.02 seconds = 12.60 MB/sec

Je trochu smutné, že práce s RAM je u nové VIA C7 s DDR2 jen nepatrně rychlejší

[Jimmy]

Sempron 2200+
Model=WDC WD307AA-00BAA0 - Westert Digital 30 GB 3,5" 5400ot

Timing buffer-cache reads: 1080 MB in 2.00 seconds = 539.27 MB/sec
Timing buffered disk reads: 72 MB in 3.02 seconds = 23.88 MB/sec

[cheyene12]

 Model=Hitachi HTS541616J9AT00                 , FwRev=SB4OA70H, SerialNo=      SB0442SJE6EZ1H
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=DualPortCache, BuffSize=7512kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1:  ATA/ATAPI-2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1232 MB in  2.00 seconds = 615.82 MB/sec
 Timing buffered disk reads:  140 MB in  3.03 seconds =  46.25 MB/sec

[Radovan Garabík]

Fujitsu-Siemens P1510:

/dev/hda:
 Timing cached reads:   2592 MB in  2.00 seconds = 1296.99 MB/sec
 Timing buffered disk reads:   64 MB in  3.08 seconds =  20.77 MB/sec

[Tomáš Srnka]

/dev/hda:

Model=TOSHIBA MK2006GAL, FwRev=BY301A, SerialNo=16SQ2510T Config={ Fixed } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=off CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39063024 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 AdvancedPM=yes: unknown setting WriteCache=enabled Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6

* signifies the current active mode

Timing cached reads: 114 MB in 2.01 seconds = 56.69 MB/sec Timing buffered disk reads: 32 MB in 3.00 seconds = 10.65 MB/sec

Inac to je toshiba 20GB 1.8"

[Michal Fecko]

super 1,8 hdparm som tu ešte nevidel...

[hajoucha]

# hdparm -itT /dev/hda

/dev/hda:

 Model=HITACHI_DK14FA-20B, FwRev=00MBA0B3, SerialNo=1R4638
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/15/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
 CurCHS=16383/15/63, CurSects=15481935, LBA=yes, LBAsects=32059073
 IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
 Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3:  ATA/ATAPI-2,3,4,5

 * signifies the current active mode

 Timing cached reads:   684 MB in  2.00 seconds = 341.19 MB/sec
 Timing buffered disk reads:   54 MB in  3.04 seconds =  17.76 MB/sec

tohle je taky 20GB 1.8".

[manasek]

hdparm -iTt /dev/sda

/dev/sda:

 Model=FUJITSU MHV2080BH, FwRev=00840028, SerialNo=NW05T6827JJK
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
 Drive conforms to: unknown:  ATA/ATAPI-3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1930 MB in  2.00 seconds = 966.46 MB/sec
 Timing buffered disk reads:  102 MB in  3.00 seconds =  33.99 MB/sec

[urys]

hdparm -iTt /dev/sda

/dev/sda:

 Model=WDC WD2500BEVS-60UST0 (2.5", 5400RPM)   , FwRev=01.01A01, SerialNo=     WD-WXEY07M77717
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=yes: unknown setting WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   2314 MB in  2.00 seconds = 1158.03 MB/sec
 Timing buffered disk reads:  166 MB in  3.00 seconds =  55.26 MB/sec

[cthulhu]

uz je to trosku starsi tema, ale at mame porovnani s novymi "rychliky":) (je to WD 640GB - 2 plotny, acoustic management off)

root@umi:~# hdparm -iTt /dev/sda

/dev/sda:

 Model=WDC WD6400AAKS-65A7B0                   , FwRev=01.03B01, SerialNo=     WD-WMASY1000288
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
 BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=?1?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=1250263728
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode

 Timing cached reads:   1394 MB in  2.00 seconds = 696.84 MB/sec
 Timing buffered disk reads:  268 MB in  3.01 seconds =  89.08 MB/sec

[2008]

md3 : active raid10 sdd6[3] sdc6[2] sdb6[1] sda6[0]
      62926336 blocks 128K chunks 2 far-copies [4/4] [UUUU]

/dev/md3:
 Timing cached reads:   10110 MB in  2.00 seconds = 5058.98 MB/sec
 Timing buffered disk reads:  724 MB in  3.00 seconds = 240.97 MB/sec

[Thu Sep 18 20:25:01 2008]

md8 : active raid10 sdd7[3] sdc7[2] sdb7[1] sda7[0]
      62914560 blocks 4096K chunks 2 far-copies [4/4] [UUUU]

/dev/md8:
 Timing cached reads:   10488 MB in  2.00 seconds = 5248.88 MB/sec
 Timing buffered disk reads:  972 MB in  3.00 seconds = 323.99 MB/sec